The project looks good but I think you could make a couple improvements to it that would make it really durable. I would start by enclosing the turbine and wiring give them a dry place to operate. Also the bearings that you welded to the frame could become an issue if you ever have to replace the bearings. I don't think you could replace the bearings without cutting them out of the frame. The project is still an excellent demonstration of what is possible!
Honestly, the "free energy" in the hashtags threw me off, because there's no free energy in the world. But apart from that, I see nothing wrong with your videos, despite the (somehow) many red flags on your channel. Thanks for not spreading misinformation! You're one of the few truly DIY channels out there, keep it up!
@@kusukacolaylowlee1611 then you are living heave bro... Sun has limited energy, but it can run more than a 100 million times average human life, so you say that it is free. But in physics, there is no free energy
I love these videos so much, you will save lives if the zombie apocalypse ever happens. Thank you seriously though, this is amazing and you taken the time to educate us all is amazing! Thank you so much and mad love, I subscribe and like each of these kinds of videos I see! Mad love 🤘🏻
@@mr.construction9846 screws have been used to draw water up from Wells and rivers in times past even to irrigate the hanging gardens of babylon the crank system was wooden based simple cog system turned by men or beast. Water falling on to the screw generators power like a giant Water wheel that Turned the stone which ground the wheat,in the bread Mills. Screws are used on all ship in the ocean to draw themselves though the water just 3 separate blades in a "spiraling array"
Hello, great work another like, you are blessed with that amount of water, but the watt meter measures 40 Volts, it increased twice the voltage with respect to the single Archimedes turbine, but it gives 0 Watts (0 Amps) the single Archimedes turbine gave 0.3 Amps. Am I missing something here? Did you connect the load? 9:37 How many watts does this configuration produce? Thanks in advance for your answer.
@@mr.construction9846 entonces que utilidad tiene el circuito que utilizas, ese me gustaria conocer sus componentes para un proyecto que me toca realizar, gracias
The construction company I work for is actually building a large scale one of those in a levee at out local regional airport. There's 3 screws and each are rated for 10,000 gallons a minute, yes you read that right 10,000 gallon per minute for just 1 screw and there's 3 of the screws
Cool! But I had an idea that the screws would be better made of metal. Being heavier, they will act as flywheels, which will give a smoother rotation when the water flow in the canal changes. And it will give more inertia to the whole system. Or you can fill the auger axles with inert material, sand or gravel. That will also increase inertia.
I have no better words to say this: In a worm drive, when torque is applied to the worm, which is essentially a screw, the worm wheel rotates, but the torque applied to the worm wheel does not rotate the worm. Ironically, the Archimedean screw can rotate in both directions due to the flow of water. Interesting...
You should Get A Vertical Vertex Delta 3D Printer + Recycle plastics to Filament Arger Extruder (Plastic Bottles to Filament) Advantage of a 3D Printer is you can make Wider & very long Tube Arger multi Screw interlocking Segments that just Lock together (Nylon Bolt and Nylon NUT Together) to make even longer Screw Turbines More K Watts From very Low Water Heads
The small circle is 60mm in diameter, the big circle is about 200mm, I have a detailed video tutorial on how to make Archimedes screws, you can watch and apply with the desired size
I have some questions. First, what is the distance between each part of the archimedes screw. Second, what is the material that is used in making the turbine. Third, what was the velocity of the water to make the turbine rotate like that. Fourth, what is the number of rotations on that scale of one screw
There is a video where I have a tutorial on how to make a screw, the rest of the questions I don't measure directly, so I can't answer you. For this motor, the rpm is about 400 and the power is already out as shown in the video
it shows 38 volts, but how many amps is this capable of? I am going to assume very little, maybe 200 mA so this would be about 7.5 watts -- and that's being generous. Still cool but would have like to see the actual numbers. Volts only tell half the story.
add a bigger gear on the turbine smaller gear on the generator, use rubber pully, have each turbine run its own generator so you're not losing power driving the other turbine if the turbines arnt flowing the same amount of water. No?
@@brentmyran1410 1: Any good engineer would love feed back. and doesn't let ego get in the way 2: I don't have a need, nor a tiny water way to perform experiments. 3: If you feel there are better suggestions than mine make everyone else smarter and provide them.
@@pnuema1.618 I just want to see your turbine . Your mister better then everybody And there is adding some suggestions and then there's you . You don't think he knows all your ideas already he built the thing . I don't see anything by you yet or you just the guy that adds on to everyone else's idea nothing original yourself I'm sure you will correct my Grammer next.
Now dig a trench from the Pacific ocean to Death Valley and line it with turbine power, pfft, climate solved, turning Death Valley back into a lake would lower sea levels and create rain and drinking water...
Given a size of generator used i would be suprised if it can do more than 5amps 12v under load. Which is not much but for 1 h3 lightbulb that is 55W at 12v it should do the job and it's lot of light. So if you think boiling water or curling wood it's no no but some simple. Ligting especially with led's. Should be perfect.
@@mr.construction9846 here in my country (brazil), 30 percent of the population is rural. Living on farms is something that is part of the childhood of many Brazilians. So, it is common to have biodigesters to generate gas, create hydroelectric wheels, and reuse all the waste. But in cities it is completely the opposite!! It only takes a little bit to buy my farm. the best place for an engineer!!
The project looks good but I think you could make a couple improvements to it that would make it really durable. I would start by enclosing the turbine and wiring give them a dry place to operate. Also the bearings that you welded to the frame could become an issue if you ever have to replace the bearings. I don't think you could replace the bearings without cutting them out of the frame. The project is still an excellent demonstration of what is possible!
i think cones instead of the flat pipe bunges would help on the flow rate a touch as well
You do not understand ! This project was designed for video views, not turbine life!
Thanks, it's just an idea I wanted to convey, it still needs a lot of improvement
@@АлександрКузнецов-е5о7г well said
Honestly, the "free energy" in the hashtags threw me off, because there's no free energy in the world.
But apart from that, I see nothing wrong with your videos, despite the (somehow) many red flags on your channel.
Thanks for not spreading misinformation! You're one of the few truly DIY channels out there, keep it up!
th-cam.com/video/uBg5FAw3b48/w-d-xo.html
Sun is free energy!
@@kusukacolaylowlee1611 then you are living heave bro... Sun has limited energy, but it can run more than a 100 million times average human life, so you say that it is free. But in physics, there is no free energy
@@behumanist sun can focus with lense to cook! Free energy!
Potential energy from water is free energy, is'nt it...
Yet another awsom productive project well done my friend 👍👍👍👍👏👏👏👏👏👏👏👏👏👏👏
Thank you
th-cam.com/video/uBg5FAw3b48/w-d-xo.html
Wow I am amazed.... I could not make out the numbers how much power was coming off that beauty nice work bud
Thanks 🌹🌹🌹🌹🌹🌹
congratulations good friend 👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻🇧🇷
Thank you
I love these videos so much, you will save lives if the zombie apocalypse ever happens. Thank you seriously though, this is amazing and you taken the time to educate us all is amazing! Thank you so much and mad love, I subscribe and like each of these kinds of videos I see! Mad love 🤘🏻
Thank you very much 🌹🌹🌹
hàn như đúng rồi ý bác hihi
😂😂😂
Absolutely Awesome 👏👏👏🕊❣🔥🙏
Thanks
Nice one , great job
Thank you
I like that he powers a fan with this turbine, so that he now can make wind to power his wind turbine.
Haha, great idea 😂😂😂
Very creative
Beautifully done!
Thank you
Beautiful workpiece 👍
Thank you
th-cam.com/video/uBg5FAw3b48/w-d-xo.html
Absolutely awesome idea for creation
Wow thats awesome! such good use of the concrete sides to make a height difference.
👍👍👍👍👍
The Greek master would be proud 👍the power stored then used to power the screw the in reverse to draw the water upwards to a higher plain.👌
That is not possible
@@mr.construction9846 screws have been used to draw water up from Wells and rivers in times past even to irrigate the hanging gardens of babylon the crank system was wooden based simple cog system turned by men or beast. Water falling on to the screw generators power like a giant Water wheel that Turned the stone which ground the wheat,in the bread Mills. Screws are used on all ship in the ocean to draw themselves though the water just 3 separate blades in a "spiraling array"
Amazing skills and later free energy 💪👌
Thank you 🌹🌹🌹
Woouuww,,, absolutely awesome, you got new subscribed 👍👍👍
Thank you bro 👍👍
Xịn quá a ơi
th-cam.com/video/uBg5FAw3b48/w-d-xo.html
Cảm ơn bạn
You are amazing dude
Thanks
Pretty damm good..great job..thanks for sharing
Thanks
wow man, this is so cool
Thanks
Number 1👍😉
Thank you 🌹🌹🌹
Wow! That has lots of power!
👍👍👍👍👍
Premiu nobel 👏
th-cam.com/video/uBg5FAw3b48/w-d-xo.html 🥰
정말 멋진 작품입니다.
회로 방수, 녹 발생을 최소화 한다면 장기간 사용 할 수 있는 제품이 나올것 같아요.
실제 적용을 위해서는 많은 개선이 필요합니다
Good work. Amazing. I would like to know if this project could Increase dosolved oxigen in water. What do you know about that? Thank you.
Thanks, Of course it is possible
أحسنت صنعاً
Thanks
I think you should try it with fully enclosed screws will make more use of the waters weight all the way around the screw
I haven't tried it but I haven't seen a real life model that makes a sealed tube
I thought the samething but checked to see if anyone commented.
Or a little wall perpendicular to the screw's thread-edge, so the outward velocity water redirects some of the energy back, like a Pelton wheel
Pretty cool inefficient water pump!
😢😢😢😂😂😂
Nice
Thanks
@@mr.construction9846 welcome
Brilliant
Thanks
Top top dos tops, tem gente que o talento e sem fim
Parabéns
Thank you
More grace to your elbow bro, nice work there, big shout-out to you.
Please which motor did you used.?
It is the motor of the air conditioner
Super
Thanks
Hello, great work another like, you are blessed with that amount of water, but the watt meter measures 40 Volts, it increased twice the voltage with respect to the single Archimedes turbine, but it gives 0 Watts (0 Amps) the single Archimedes turbine gave 0.3 Amps. Am I missing something here? Did you connect the load? 9:37 How many watts does this configuration produce? Thanks in advance for your answer.
I measured it with no load, when loaded it also reached the same apm number as a single turbine
Muy buen invento
Thanks
Hi support
welding bearing and work in water ?
👍👍👍
Could you tell me the installation of the circuit and the components? greetings thank you. Excellent video
It is the motor of the air conditioner . It outputs dc current without you needing to do anything
You can refer to here : bit.ly/3lfjnW7
@@mr.construction9846 entonces que utilidad tiene el circuito que utilizas, ese me gustaria conocer sus componentes para un proyecto que me toca realizar, gracias
The construction company I work for is actually building a large scale one of those in a levee at out local regional airport. There's 3 screws and each are rated for 10,000 gallons a minute, yes you read that right 10,000 gallon per minute for just 1 screw and there's 3 of the screws
The energy generated will be huge
@@mr.construction9846 these that we are building are actually water pumps to remove water run off from the air field
Cool! But I had an idea that the screws would be better made of metal. Being heavier, they will act as flywheels, which will give a smoother rotation when the water flow in the canal changes. And it will give more inertia to the whole system. Or you can fill the auger axles with inert material, sand or gravel. That will also increase inertia.
Very good and useful idea. thank you 👍👍👍
Just add a flywheel!
What motor did you use?
Nice work!
It is the motor of the air conditioner
Good job!! What kind of motor do you use??
It is the motor of the air conditioner
Welding rubber sealed deep grove ball bearings directly to something is a new one.
👍👍👍👍
Parabéns muito top amei 👏👏👏👏👏👏👏👏👏👏
Thanks
super 😍🔟➕👑💪😁🍷😋
Thanks
good works sir...next time try to charge your phone on your project👍👍
Ok bro
Eu não entendi!
Vc teve essa baita trabalheira pra ligar um ventilador?
É muito quente aí... é por isso?
Apenas para testar a potência de saída
Hello here!
Could I please know, where can we get those PVC flat sheets?
Cut the PVC pipe and use fire to flatten it
Fire curing glue?
Epoxy glue
what motor you used? so nice to copy this.
It is the motor of the air conditioner
@@mr.construction9846 DC motor of aircon???
Süper.
👍👍👍
Fajnie pokazane za to szacunek ale można dużo poprawić np.zamkniete rury zwiększą sprawność
👍👍👍 Zamknięte rury, gdy pojawia się problem, są dość trudne do naprawienia, chociaż wydajność będzie wyższa
is it really save? i mean if the water suddenly overflowing...
If it's the flow of a river or any other natural flow then it doesn't matter anymore
where you able to measure the output for the screws?
🙄🙄🙄😂😂😂
ASSALAMUALAIKUM
Is there any video about vertical cross flow turbine?
There's a model I've been working on for quite a while, so I'll make another one soon
what kind of motor did you use?
It is the motor of the air conditioner You can refer to here : bit.ly/3lfjnW7
I have no better words to say this: In a worm drive, when torque is applied to the worm, which is essentially a screw, the worm wheel rotates, but the torque applied to the worm wheel does not rotate the worm. Ironically, the Archimedean screw can rotate in both directions due to the flow of water. Interesting...
*Hows that work out in the desert 🤔*
Let's use solar energy
Where did you get motor from???
It is the motor of the air conditioner
Be interesting to see what power its creating in volts ah and Watts
I measured it, unfortunately it didn't get into the camera
@@mr.construction9846 what was the reading?
You should Get A Vertical Vertex Delta 3D Printer + Recycle plastics to Filament Arger Extruder (Plastic Bottles to Filament)
Advantage of a 3D Printer is you can make Wider & very long Tube Arger multi Screw interlocking Segments that just Lock together (Nylon Bolt and Nylon NUT Together) to make even longer Screw Turbines More K Watts From very Low Water Heads
I will study your opinion
What kind of materials did you use to make an archimides?
It is a PVC pipe, you should flatten it with heat, shape it and glue it with epoxy glue
How much power does it make
About 20w
How many watt can produce?
maybe 15w
can i know what spocket size you using?
Not much power generation. How much? I can't see the meter in the video. I do hear the drag on the turbines for a desktop fan.
yeah. It is about 40v 20w
Why not two Propellers.? If the archimedian screw was that efficient it would be powering tankers
In my opinion, the torque generated from the screw will be much larger than that of the propeller
To make turbin, can you tell me how diameter of the circle.. Small circle and big circle
The small circle is 60mm in diameter, the big circle is about 200mm, I have a detailed video tutorial on how to make Archimedes screws, you can watch and apply with the desired size
I have some questions. First, what is the distance between each part of the archimedes screw. Second, what is the material that is used in making the turbine. Third, what was the velocity of the water to make the turbine rotate like that. Fourth, what is the number of rotations on that scale of one screw
There is a video where I have a tutorial on how to make a screw, the rest of the questions I don't measure directly, so I can't answer you. For this motor, the rpm is about 400 and the power is already out as shown in the video
What are the materials
It's the air conditioner motor
Where can I get this turbine bro
The Archimedes screw actually lifts water, this is a screw powdered generator, but thats all.
th-cam.com/video/XjEgFlngZ04/w-d-xo.html
That's it
I see @ 8:45 it slow down when the load is applied 😌
Exactly
What Glue did you use?
It's epoxy glue
Hmmm producing maybe 12 V ?
~40v, you can see it in video
What is the spec of the motor you used?
It is the motor of the air conditioner
How can i buy your project?
What is the price of this turbine motor ?
Never have I ever seen a bearing being welded.. until now.
Hahaa 😂😂😂🌹🌹🌹
Can i know the parameters and specifications of the project of each component pls😊😊
Bang barang nya di jual ga? Kalo di shope ada aku pesen ni
Maaf tidak, saya hanya membuatnya untuk dilihat semua orang
please list the used materials
PVC pipe and motor of the old air conditioner, about how to make the screw, please refer to the internet, I'm really not good at expressing
Berapa panjang turbinnya?
Panjangnya bisa 90cm
it shows 38 volts, but how many amps is this capable of? I am going to assume very little, maybe 200 mA so this would be about 7.5 watts -- and that's being generous. Still cool but would have like to see the actual numbers. Volts only tell half the story.
Sorry I forgot
7.5watts。。。
why does the speed of the turbine decrease when the table fan was connected? 🤔 fishy!
I'm not really good at physics either
add a bigger gear on the turbine smaller gear on the generator, use rubber pully, have each turbine run its own generator so you're not losing power driving the other turbine if the turbines arnt flowing the same amount of water. No?
You gonna do a video with all your awesome ideas .
Sounds like you must have a way better rig
@@brentmyran1410
1: Any good engineer would love feed back. and doesn't let ego get in the way
2: I don't have a need, nor a tiny water way to perform experiments.
3: If you feel there are better suggestions than mine make everyone else smarter and provide them.
@@pnuema1.618 your the one with all the big ideas
@@brentmyran1410 You're the one who seems to have an issue with it.
@@pnuema1.618 I just want to see your turbine .
Your mister better then everybody
And there is adding some suggestions and then there's you .
You don't think he knows all your ideas already he built the thing . I don't see anything by you yet or you just the guy that adds on to everyone else's idea nothing original yourself
I'm sure you will correct my Grammer next.
Dinamo bekas apa itu ?,
Dimensi turbin brpapa cm termasuk lingkaran n lingkaran tengahx,
Lumrah ini didesa2! Buat nyalain lampu malem2
Ini adalah motor di AC
Check out ness power inverness.
fucking awesome 👍👍👍but please tell me what You used as the motor
It is the motor of the air conditioner
@@mr.construction9846 thx Bro 🙂
This is the start of a comment thread.
👍👍👍🌹🌹🌹
У тебя такой крутой сварочный аппарат. А маска хрень.
😂😂😂
Now dig a trench from the Pacific ocean to Death Valley and line it with turbine power, pfft, climate solved, turning Death Valley back into a lake would lower sea levels and create rain and drinking water...
Hahaa. Great idea 👍👍👍
why to do so much.. just connect the
fan with the gear belts it will rotate with the water
🙄🙄🙄😢😢😢
This is a video for electroboom to verify.
Gg
Хероборина
Fake
Why?
Why?
how many watts does it produce?
Given a size of generator used i would be suprised if it can do more than 5amps 12v under load. Which is not much but for 1 h3 lightbulb that is 55W at 12v it should do the job and it's lot of light. So if you think boiling water or curling wood it's no no but some simple. Ligting especially with led's. Should be perfect.
Its amperage is approximately 0.4A, the system range is greater than 10w
@@mr.construction9846 here in my country (brazil), 30 percent of the population is rural. Living on farms is something that is part of the childhood of many Brazilians. So, it is common to have biodigesters to generate gas, create hydroelectric wheels, and reuse all the waste. But in cities it is completely the opposite!! It only takes a little bit to buy my farm. the best place for an engineer!!