a good idea, but overly engineered. one. there was no need to round off the nut that tightens onto the steel rod. two, the bearing didn't need to be welded as it spins anyway. three, the loop made for the turning bar had 4 welds. why not bend a strip off steel in a loop and need only 2 welds. better yet just weld a short length of larger dia pipe that the bar could slide into.
One of the many videos about making a bar bender. Why should one want to make a tool that can only bent bars of a specific diameter and at a specific radius makes sense only if one needs hundreds of them. If not, it is a time wasting exercise of practical low level mechanics. Is the author going to sell the bent bars? Is he going to use them in some kind of foundation? Is he living in a third world country where bent bars are in great demand? Well, if it makes people happy, I suppose it was worth it.
Repent to Jesus Christ! Are you a sinner? Luke 5:32 King James Version 32 I came not to call the righteous, but sinners to repentance. Luke 13:3 King James Version 3 I tell you, Nay: but, except ye repent, ye shall all likewise perish.
I like it 👍
Repurposing material is intelligent. Good instruction.
Bom demais!!
Very good Chanel bro 💯 idea I subscribed your channel
Sehr nett von dir , die einzelnen Arbeitsschritte im Zeitraffer zu zeigen und nicht gähnend langweilig in die Länge zu ziehen,
Gibt ein like!
Bagus 👍🤝🇮🇩
Very very nice Chanel bro good 👍 ideas great video I subscribed your channel
thanks. good idea
How much does a bending tool cost?
15$ bro.
It's a great idea ♪
Thank you 😊
Your Chanel very nice 💯 idea great video I subscribed your channel
That's a lot of fabrication for a (not so) simple rod bender.
This is about the 50th video of this particular type of welded idea.
How do you do this without a welder some of us don't own one
Nice job 👍
Thanks
@@CreativeToolMistry ppplp0o
Very good your Chanel 💯 idea great video 👍I subscribed your channel
Excellent 👏
Thank you 😊
HOMEMADE ROD BENDER - WHOOPEE DO !!
OMG! The world will never be the same.
a good idea, but overly engineered. one. there was no need to round off the nut that tightens onto the steel rod. two, the bearing didn't need to be welded as it spins anyway. three, the loop made for the turning bar had 4 welds. why not bend a strip off steel in a loop and need only 2 welds. better yet just weld a short length of larger dia pipe that the bar could slide into.
Good work bro
Thank you 😊
Good idea but if anyone has the time or money to that why not just buy one.
Getting flashes from the welding going on . Need to put shield on !
Good luck welding on a case iron pulley.
Yes, I too thought that the Pulley Wheel was cast iron. An awful job.
One of the many videos about making a bar bender. Why should one want to make a tool that can only bent bars of a specific diameter and at a specific radius makes sense only if one needs hundreds of them. If not, it is a time wasting exercise of practical low level mechanics. Is the author going to sell the bent bars? Is he going to use them in some kind of foundation? Is he living in a third world country where bent bars are in great demand? Well, if it makes people happy, I suppose it was worth it.
Good job Sir ❤️
Thanks
Good
reading the comments, its obvious that we do know about this type of tool. and its not really new, or even different from any other bender.
Bender from Futurama would be jealous
That was 6 minutes and 21 seconds of wasted time.
o think thar is a kind of pipe Bemder.
Budhusaranayi .....!
Your video has down but why hii I am TH-cam ber Avinash ka laboratory
Привет, я считаю напрасный труд.
Точно
Наверно больше заняться нечем😂😂
Mantul
Repent to Jesus Christ!
Are you a sinner?
Luke 5:32
King James Version
32 I came not to call the righteous, but sinners to repentance.
Luke 13:3
King James Version
3 I tell you, Nay: but, except ye repent, ye shall all likewise perish.
8
sfw?
No need to know this...
Зачем придумывать колесо.....?!!
Good