Thank you, Craig; this was very helpful. I was able to clean the impeller. There was a lot of hair built inside. As a preventative measure, I would recommend doing it once a year. It took me 15 minutes.
I've found that if you place the unit on your knee, so that the tracks are on either side of your thigh, the motor will slide in easily because the track gear rotates freely as the motor cog is inserted.
Craig I have an issue that when I turn the power supply on, it only flashes. This is with the cleaner hooked up. With the cleaner unhooked, the power supply acts correctly. Nautilus CC
I assume they quit making these expensive power supplies with replaceable fuses so they can sell more rather than consumer being able to fix in minutes. Designing something that works only in and around water and is not waterproof is foolish, just want to make more and more money....just my opinion of course.
I might be wrong as I am in Australia and ours might be different, but the 1, 2, 3 settings is how many days consecutively the unit runs, not how many days apart. This is so the the cleaner draws back the operator to check the filter with the idea being to prevent it continuously running with a full cleaner basket.
Any answer to this, it is my exact issue ?When I turn the power supply on, it only flashes. This is with the cleaner hooked up. With the cleaner unhooked, the power supply acts correctly. Nautilus CC Pro
Great informative video. When I start the system the robot starts to work but stops in less than a minute. I checked the impeller on the robot and found it to be clean. The controller box feels warm and when I checked it with the voltmeter I got a negative 1 on DC20. If I bump it up to DC200 I get negative 29.6. Any thoughts? I leaning on the power control box.
You get a negative reading because your leads are reversed if checking with a digital multimeter. If not checking with a DMM then you have other wiring issues. Yes and when checking with a voltmeter you have to set you limit, HIGHER, than the voltage your wanting to check. In other words if one was wanting to check voltage of say 240 volts, then you need to set your dial to greater than 240. I hope that helps. The thing I found with my daughters unit, after taking the motor unit clear apart that it had a lot of moisture inside the motor/control box. This is supposedly a "sealed" unit since it had a rubber gasket to help seal it to make it water proof. However, the motor that spins the impeller is NOT sealed thus allowing the unit to take in moisture. This is definitely a design flaw because there are several electrical components inside that will eventually short out and thus make one have to buy the motor unit this video is talking about to the tune of over $400. The motor that spins the impeller has two capacitors inside its casing and they were WET not just damp thus they had shorted out. The two long bolts that hold this motor together were severely rusted. Again, this is a design flaw, of course, this is just MY opinion. This is why the control/motor unit is NOT under warranty. If THEY, the company, had to pay to replace these units because of this flaw, they would design them where they were totally waterproof. Otherwise, I will say the unit does a SUPERB job of cleaning!!! Again, just like everything else made today, they only want it to last so long, then they want you to buy another one. It is the ole "PLANNED OBSOLESCENCE" scheme.
Hey Craig, I appreciate the video but after I confirmed the power supply and cable were working and I installed a new motor block my active 20 does not move. I have left two messages on your website but have not heard from you in return. I need to know what else could be my problem .
The blue power light on mine comes on for half a second then immediately turns off, but only when the device plugged into the power supply. When it's not plugged in, the power supply will turn and stay on like normal. Impeller is not jammed up.
I have an inoperative Dolphin Deluxe 4. I opened the motor. There is 29DCV across the b&w pins. There is no continuity from the red pin to the power supply end of the cable. I didn't notice any obvious failures on the PCB. Leslie's used their plug diagnostic tool and checked the cable as "good." Is the red wire used? I need to know before I purchase a new motor unit.
Thanks for the video Craig, would you happen to have a failed motor module you'd be willing to part with? Our Dolphin 20 climbs the wall and I'd like to look at the controller board to see if there's a way to disable vertical wall climbing and better to look at something I might break is disassembly than a working unit.
Mine runs for a minute and then the LED on the PCB inside the motor block flashes rapidly. The connector for the water motor has gotten hot enough to discolor the plastic. I'm going to solder and heat shrink that pigtail and see what happens. Do you have any info on that flashing LED? Motor driver, poor connection, high output current???? Thanks
At 08:00 into your Maytronics Active 20 video (th-cam.com/video/5Ocz-PH0DWQ/w-d-xo.html) you mention that home automation instructions would be provided later in the video, and a pdf can be downloaded from your website. I didn't see those instructions in the video, and cannot find the related pdf on your website, please comment.
My active solo track keeps coming off. Installed new tracks same issue is there a belt Tightener or some way to fix this issue? Can't find a fix on web or company's web site.
My unit starts running for about 90 seconds and then stops. The impeller is clean and so are the track wheels. I have found sometimes hair get caught there, but not this time. Any thoughts?
Same problem here. Impeller runs, traction motor runs. Shuts off. I'm going to take some readings while it's running and after it shuts off. The little LED on the control board inside the dolphin is flashing rapidly. The pigtail from the impeller motor to the control board has another pigtail where the manufacturer added a slug. The wire to wire connector got hot enough to melt a bit. I'm going to cut the plugs, solder, and heat shrink. We'll see. If it works I'll put a video on my channel.
Can you please tell me I have the unit with the remote control from your phone app but they won’t recognize to work can you tell me why it say you can’t find the unit even you stay next to it
Im hoping someone might be able to help. My controller got water in it. Now when you hit power button, it lights up for 10 seconds and goes off. Ive dried it out and same. Does anyone know what this is?
My Bluetooth don’t work on the unit can you tell me why is that and how can I make it recognize I’m working again I don’t know how to check it thank you
Thank you for the perfect and detailed presentation!
Thank you, Craig; this was very helpful. I was able to clean the impeller. There was a lot of hair built inside. As a preventative measure, I would recommend doing it once a year. It took me 15 minutes.
Thank you for posting this Video !! Used this to replace a chewed cord. Dogs got a little hungry!
I've found that if you place the unit on your knee, so that the tracks are on either side of your thigh, the motor will slide in easily because the track gear rotates freely as the motor cog is inserted.
best dolphin video ive seen so far! great job!
Craig I have an issue that when I turn the power supply on, it only flashes. This is with the cleaner hooked up. With the cleaner unhooked, the power supply acts correctly. Nautilus CC
Mine don't even flash no light at all
I assume they quit making these expensive power supplies with replaceable fuses so they can sell more rather than consumer being able to fix in minutes. Designing something that works only in and around water and is not waterproof is foolish, just want to make more and more money....just my opinion of course.
Excellent advice. Thank you 😊
I might be wrong as I am in Australia and ours might be different, but the 1, 2, 3 settings is how many days consecutively the unit runs, not how many days apart. This is so the the cleaner draws back the operator to check the filter with the idea being to prevent it continuously running with a full cleaner basket.
Any answer to this, it is my exact issue ?When I turn the power supply on, it only flashes. This is with the cleaner hooked up. With the cleaner unhooked, the power supply acts correctly. Nautilus CC Pro
Yea thank you. Fixed our sweeper
So what happens if it gets rained on
whta is the part number for the motor block? Thank you
Great informative video. When I start the system the robot starts to work but stops in less than a minute. I checked the impeller on the robot and found it to be clean. The controller box feels warm and when I checked it with the voltmeter I got a negative 1 on DC20. If I bump it up to DC200 I get negative 29.6. Any thoughts? I leaning on the power control box.
Did you ever find out what the issue is? I'm having the problem.
Curious to know what the issue was with your unit and how you resolved it.
You get a negative reading because your leads are reversed if checking with a digital multimeter. If not checking with a DMM then you have other wiring issues.
Yes and when checking with a voltmeter you have to set you limit, HIGHER, than the voltage your wanting to check. In other words if one was wanting to check voltage of say 240 volts, then you need to set your dial to greater than 240. I hope that helps.
The thing I found with my daughters unit, after taking the motor unit clear apart that it had a lot of moisture inside the motor/control box. This is supposedly a "sealed" unit since it had a rubber gasket to help seal it to make it water proof. However, the motor that spins the impeller is NOT sealed thus allowing the unit to take in moisture. This is definitely a design flaw because there are several electrical components inside that will eventually short out and thus make one have to buy the motor unit this video is talking about to the tune of over $400. The motor that spins the impeller has two capacitors inside its casing and they were WET not just damp thus they had shorted out. The two long bolts that hold this motor together were severely rusted. Again, this is a design flaw, of course, this is just MY opinion. This is why the control/motor unit is NOT under warranty. If THEY, the company, had to pay to replace these units because of this flaw, they would design them where they were totally waterproof.
Otherwise, I will say the unit does a SUPERB job of cleaning!!! Again, just like everything else made today, they only want it to last so long, then they want you to buy another one. It is the ole "PLANNED OBSOLESCENCE" scheme.
It would be nice to provide the part numbers as promised like the owner's manual.
Hey Craig, I appreciate the video but after I confirmed the power supply and cable were working and I installed a new motor block my active 20 does not move. I have left two messages on your website but have not heard from you in return. I need to know what else could be my problem .
Awesome video, What is the motor block part number
The blue power light on mine comes on for half a second then immediately turns off, but only when the device plugged into the power supply. When it's not plugged in, the power supply will turn and stay on like normal. Impeller is not jammed up.
Nice video, thanks for the good info.
Hope you work on a bench, don't kill your back. Best regards.
Great video. Thank you.
The power shows on on the control box but no power light on the prowler .
Me gustó claro, breve y conciso
So when the unit lights up and doesn't let you select a schedule, the power supply is done for an must be replaced?
I have an inoperative Dolphin Deluxe 4. I opened the motor. There is 29DCV across the b&w pins. There is no continuity from the red pin to the power supply end of the cable. I didn't notice any obvious failures on the PCB.
Leslie's used their plug diagnostic tool and checked the cable as "good." Is the red wire used? I need to know before I purchase a new motor unit.
Thanks for the video Craig, would you happen to have a failed motor module you'd be willing to part with? Our Dolphin 20 climbs the wall and I'd like to look at the controller board to see if there's a way to disable vertical wall climbing and better to look at something I might break is disassembly than a working unit.
Mine runs for a minute and then the LED on the PCB inside the motor block flashes rapidly. The connector for the water motor has gotten hot enough to discolor the plastic. I'm going to solder and heat shrink that pigtail and see what happens. Do you have any info on that flashing LED? Motor driver, poor connection, high output current????
Thanks
Awesome thank you for making this LITTLE VIDEO! Great information!
Glad you enjoyed it!
At 08:00 into your Maytronics Active 20 video (th-cam.com/video/5Ocz-PH0DWQ/w-d-xo.html) you mention that home automation instructions would be provided later in the video, and a pdf can be downloaded from your website. I didn't see those instructions in the video, and cannot find the related pdf on your website, please comment.
I'm testing 35 volts coming out power supply and 28 volts at the other end of the cable. My robot vacuum is not turning on at all.
You have another problem
My active solo track keeps coming off. Installed new tracks same issue is there a belt Tightener or some way to fix this issue? Can't find a fix on web or company's web site.
how do you set the power supply?
My unit starts running for about 90 seconds and then stops. The impeller is clean and so are the track wheels. I have found sometimes hair get caught there, but not this time. Any thoughts?
That currently is my problem, I cleaned the impeller, but still shuts off, I am thinking the cable, I have a 3 volt loss fro PS to end of cable
Same problem here. Impeller runs, traction motor runs. Shuts off. I'm going to take some readings while it's running and after it shuts off. The little LED on the control board inside the dolphin is flashing rapidly. The pigtail from the impeller motor to the control board has another pigtail where the manufacturer added a slug. The wire to wire connector got hot enough to melt a bit. I'm going to cut the plugs, solder, and heat shrink. We'll see. If it works I'll put a video on my channel.
Can you please tell me I have the unit with the remote control from your phone app but they won’t recognize to work can you tell me why it say you can’t find the unit even you stay next to it
Hi my dolphin s200 is saying power supply doesn’t recognize robot dolphin sent me out a new controller. Is there any fix for this? Thanks
Do you have the part number and a place where we can order the new motor block?
Love it.
How do you unplug the power supply
Im hoping someone might be able to help. My controller got water in it. Now when you hit power button, it lights up for 10 seconds and goes off. Ive dried it out and same. Does anyone know what this is?
My Bluetooth don’t work on the unit can you tell me why is that and how can I make it recognize I’m working again I don’t know how to check it thank you
Where can I find the motor
I've got power and controller lights up when turn on nothing happens?
clean your impeller 6 screws look on you tube
This is just replacing everything this isnt trouble shooting any problems.
Only power light is on