Sure, It's very simple. You Just need a round stock threaded with the same thread as the head, M14 and you're good to go. It works for any head that have a central sparkplug hole
@@exormos a round stock that you put on the lathe and cut the thread on It so you can grab the head on the chuck. It works for all the head with central sparkplug. For the head with lateral spark plug hole you'll need a special setup
Hi, that's for transpose all the ports higher, increasing the timings. Then raising the cylinder with an alu shim to compensate and obtain a proper squish height. Then from there i tweak manually all the ports sections and timings 👍🏻
Yes it's a hss lathe tool bit that i've grinded with the radius i need, actually i have made 4 tools with different radiuses for this job. co10 stands for 10%cobalt in the alloy
L'ho ricavato io da una barretta trapezoidale hss-co10, ne ho preparati 4 con diversa raggiatura che utilizzo in base alla cilindrata e al profilo/volume che punto a ottenere👍🏻
I have researched this as well and all I can find is in relation to fuel in "fluid" form, not gaseous. Since the pressurized gas mixed with air is ignited prior to TDC and don't come into contact with with the surface of the head, I am not sure it would condense. This is of course, a theory and not proven as of yet. I can say that of all the years I have modified engines and polished heads, power valve parts, and exh ports, (basically anything that sees combustion), all it really has done was make for an easier time in servicing the cyl and removing carbon build up and offers no performance gain or performance decrease.
Ya that's not true and testing has shown that any rough surface in the combustion area is a spot that may cause pre-ignition. Combustion chamber temperatures will also prevent "condensation" of fuel. This heat is also a factor that requires richening of the fuel charge due to heat evaporation losses in the intake tract. This effect is rarely directly adjusted for but done in the overall jetting of that engine.
hi can you tell me please how you attached the head to the lethe?
Sure, It's very simple. You Just need a round stock threaded with the same thread as the head, M14 and you're good to go. It works for any head that have a central sparkplug hole
@@machiningandtuning when you mean round stock threaded you mean something like a bolt with the same threads?
@@exormos a round stock that you put on the lathe and cut the thread on It so you can grab the head on the chuck. It works for all the head with central sparkplug. For the head with lateral spark plug hole you'll need a special setup
@@machiningandtuning Thank you for your explanation my uncle has a lathe and i did it today on my AM6 50mm piston engine
Hi there. Why did you leave a step on the transition between squish band and head sealing face?
Hi, that's for transpose all the ports higher, increasing the timings. Then raising the cylinder with an alu shim to compensate and obtain a proper squish height. Then from there i tweak manually all the ports sections and timings 👍🏻
Hi thank for the video I look for the tool
"HSS co10 radius " but I found nothing.
It is DIY?
Yes it's a hss lathe tool bit that i've grinded with the radius i need, actually i have made 4 tools with different radiuses for this job. co10 stands for 10%cobalt in the alloy
Sir i have two stroke cylinder i want to increase its rpm power please help me how i can increase the speed from its ports. Please help me tell me sir
l'utensile per ri fare la camera, lo hai comprato o lo hai fatto tu?
L'ho ricavato io da una barretta trapezoidale hss-co10, ne ho preparati 4 con diversa raggiatura che utilizzo in base alla cilindrata e al profilo/volume che punto a ottenere👍🏻
👍👍
You shouldn't polish the cylinder head to a mirror, because then the gasoline condenses
Never heard something like that before, can you explain what you mean? Probably have something to do with the boundary layer theory?
I have researched this as well and all I can find is in relation to fuel in "fluid" form, not gaseous.
Since the pressurized gas mixed with air is ignited prior to TDC and don't come into contact with with the surface of the head, I am not sure it would condense. This is of course, a theory and not proven as of yet.
I can say that of all the years I have modified engines and polished heads, power valve parts, and exh ports, (basically anything that sees combustion), all it really has done was make for an easier time in servicing the cyl and removing carbon build up and offers no performance gain or performance decrease.
Ya that's not true and testing has shown that any rough surface in the combustion area is a spot that may cause pre-ignition. Combustion chamber temperatures will also prevent "condensation" of fuel. This heat is also a factor that requires richening of the fuel charge due to heat evaporation losses in the intake tract. This effect is rarely directly adjusted for but done in the overall jetting of that engine.