@@NedimTabakovic Heat rises upward and the design of this case has the PSU exhausting inside the case top corner where the ventilation holes don't exactly line up to the right edge at 2:19. The GPU on the bottom is taking air from the bottom and exhausting upwards heating the inside of the case and because the radiator is at the top, the heat rising from the GPU will be slower to escape on top + the PSU is also blocking the right side. The parts look nice but too much heat shortens the lifespan of both the expensive GPU and CPU depending on if the user will overclock or not. Instead of that solid transparent panel it would be better if case just had holes/ mesh there too. People usually mount GPUs that are that large at the top in smaller ITX cases or vertically against the large side panel.
@@mystermont2019 the only problem about this PC is the dust inside it because there's zero intake (it should be on bottom). Otherwise cooling capabilities should be enough for gaming. PSU is not a problem because it's a platinum PSU, it won't heat that much (though titanium would be better). GPU heat will raise CPU temps because of exhausting through radiator - shouldn't be a problem in games as well.
@@stam1ska You can't say cooling capabilities are enough for gaming if you don't know which games will be played. Also the PSU would heat up just not enough to be a problem but hot enough to lower the lifespan of the components again because the heat from the GPU rising and eventually making contact with the PSU. I've tried various configurations with the PSU taking air from inside the case when gaming and it always exhausts hotter air than when you are taking air from outside the case which has never exhausted hot air. You don't need titanium or even platinum PSU if you setup the PSU to intake air outside the case. The heat from the GPU raising up is a problem because the radiator slows the speed at which the hot air will escape. The radiator is not the same as an air cooled heat sink. The fins actually have channels inside where the coolant liquid is passing through and it is hot. Air cooled heat sink fins are thinner and can exhaust the air faster but not only is the air being slowed down by the radiator but also the fans which draw air only from a small distance below it. The reason the case has holes on the left wall of the GPU is to mount your exhaust fans. This PC will feel like a heater in the room because of how much slower the GPU heat will take to leave the case.
@@mystermont2019 I'm taking into consideration games which are able to stress CPU hard while being graphically advanced at the same time, which is Cyberpunk 2077 at the moment (TLOU part I was harder on CPU, but it got patched). About PSU - it intakes from the outside here. About radiator - you're overthinking things, let the fans do the job. If radiator was as restrictive as you think then CPU would overheat because radiator wouldn't cool enough.
the 12vhpwr connector of the gpu is not properly plugged ,as you can see in the video ,the little "latch" is a little open ,so the connector is loose ,that could cause the known burning connector issues...
that is an amazing video well done .. but how to get this case ??? it is not available on the official website. also what kind is the power adapter that you used ? thank you
Пока не покажут температурные тесты видеокарты и процессора в этом корпусе, он является красивым куском дерьма. Все будет очень сильно греться, вентиляторы будут гудеть на полную мощность. Я не рекомендую его к покупке без тестов.
amazing compact build with FULL size GPU
每一步都非常清楚，还列出了配置，赞 🌺🌺
creation of an mini-oven. great!
A bit worried of the thermals 🤔
Just keep on worrying while he games 🫣🤭🫢
@@NedimTabakovic Heat rises upward and the design of this case has the PSU exhausting inside the case top corner where the ventilation holes don't exactly line up to the right edge at 2:19. The GPU on the bottom is taking air from the bottom and exhausting upwards heating the inside of the case and because the radiator is at the top, the heat rising from the GPU will be slower to escape on top + the PSU is also blocking the right side. The parts look nice but too much heat shortens the lifespan of both the expensive GPU and CPU depending on if the user will overclock or not. Instead of that solid transparent panel it would be better if case just had holes/ mesh there too. People usually mount GPUs that are that large at the top in smaller ITX cases or vertically against the large side panel.
@@mystermont2019 the only problem about this PC is the dust inside it because there's zero intake (it should be on bottom). Otherwise cooling capabilities should be enough for gaming. PSU is not a problem because it's a platinum PSU, it won't heat that much (though titanium would be better). GPU heat will raise CPU temps because of exhausting through radiator - shouldn't be a problem in games as well.
@@stam1ska You can't say cooling capabilities are enough for gaming if you don't know which games will be played. Also the PSU would heat up just not enough to be a problem but hot enough to lower the lifespan of the components again because the heat from the GPU rising and eventually making contact with the PSU. I've tried various configurations with the PSU taking air from inside the case when gaming and it always exhausts hotter air than when you are taking air from outside the case which has never exhausted hot air. You don't need titanium or even platinum PSU if you setup the PSU to intake air outside the case. The heat from the GPU raising up is a problem because the radiator slows the speed at which the hot air will escape. The radiator is not the same as an air cooled heat sink. The fins actually have channels inside where the coolant liquid is passing through and it is hot. Air cooled heat sink fins are thinner and can exhaust the air faster but not only is the air being slowed down by the radiator but also the fans which draw air only from a small distance below it. The reason the case has holes on the left wall of the GPU is to mount your exhaust fans. This PC will feel like a heater in the room because of how much slower the GPU heat will take to leave the case.
@@mystermont2019 I'm taking into consideration games which are able to stress CPU hard while being graphically advanced at the same time, which is Cyberpunk 2077 at the moment (TLOU part I was harder on CPU, but it got patched).
About PSU - it intakes from the outside here. About radiator - you're overthinking things, let the fans do the job. If radiator was as restrictive as you think then CPU would overheat because radiator wouldn't cool enough.
the 12vhpwr connector of the gpu is not properly plugged ,as you can see in the video ,the little "latch" is a little open ,so the connector is loose ,that could cause the known burning connector issues...
yeah both plug seems not all the way in, could be just the angle of the camera
Apparently the melting connector happens even when its properly seated so i dont know
That shit is hotter than a neutron star
fodase krl, bglh ta lindo
Reapresentou mané. Inclusive quero saber que case é esse. É menor que o Sama im01?
@@pedro.alcatra o case é o COOJ Z18, mas ele é uma nota 2k sem imposto no aliexpress kkkk
@@pedro.alcatra olha, não sei se é menor mas ele tem as medidas parecidas.
@@crow3098 Imposto é meu pau. Moro em portugal
that is an amazing video well done .. but how to get this case ??? it is not available on the official website. also what kind is the power adapter that you used ? thank you
u can search it 90 degree angle atx 3.0 gpu adapter
I a PC builder
I like this mini set up and it looks clean and also portal for tiny space.
junk! that pc in that case will give half fps you can gat in normal case
@@besogociridze bullshit
@@crassusmaximus5879 ok you think people are idiots putting there parts in big case?! yes? ))))))))))
@@besogociridze you dont know what you are talking about
@@besogociridzebruh lmao
Wow that's the most expensive MATX case I've ever seen.
What's it called?
Edit; Oh nvm, COOJ Z18.
rmb
@@Zalionn CaseEnd
Small form factor tax.
Зато дизайн стекла как из 00годов
Son derece minimal bir kasa 🎉 ama bir o kadar da güçlü ve güzel ❤❤❤
Also the thermal dissipation is looking a little warm
Case price is insane
it's a nice case until I saw that the PSU served as the intake in the front 💀wonder how the thermals are in this case
it literally is a bbq stove ngl
You should see the price of this thing...
It's surely gonna be hot, no way. Poor air circulation 😂
Looks come with drawbacks
Ага сгорит все нафиг
问题在于，这些装机看起来漂亮，温控怎么样呢？
Do you think that it is possible to make the exact same build but with a MSI GeForce RTX 4090 SUPRIM LIQUID X 24G ?
What a compact What a compact power! 😍
RTX 4090 Be like :😷🥵
Core i9 :😐⚠️
super aesthetic and very hot configuration!
0:16那邊cpu卡榫換成什麼阿? 一直看到但不知道哪裡買，用那個會比較好嗎?
利民cpu扣具, 換了後能降低主機板因為原廠扣具而壓彎的機會
CPU溫度降低1-3度
但可能會失去保養
I like that build, great colour combo.
amazing compact build but how the heck do you cool off that massive gpu in such a small space?
should work out perfectly fine. the gpu is so big because it has such a big cooler. gets fresh air from under it
im sure that 4090 temps wont go so high
the 4090 looks so big mostly because of its fans... the pcb itself is only about 10% bigger than the 4070.
@@dueterdot855 my 1080 has a smililar case and i go to like 80c with my side panel on and with it off its 46c
下面可以加2个slim fan 4090应该会很热吧。
CPU：“终究是我一个人扛下了所有。” “你清高，你了不起，我就只配用废气降温。”🤣
I don't understand how this case can be so expensive. It's at least double the price of what it should be, unless I'm missing something.
I think it’s cause the housing is one piece machined aluminum and it’s a small production case
Because the things are higher quality, the motherboard, ram and gpu and cooler are hefty
How much is the total cost in dollars of the whole thing? Im curious
3000-3500$
looks like you can fit a couple of 120mm low profile fans at the bottom.
they won't help
why don't we have these cases in mainstream brands 😭😭
散熱OK嗎
沒超頻應該可以
Will COOJ Z-13 14.6L fit this built?
Nice case for mATX, but the prices of $500us (Case+Shipping+tax) just for the case..... SIGHT!!!!!
But what about screen 3:40 ? Model pls... or this is ipad lcd+ DP to eDP board ?
How does the monitor receive the picture?
What electric screwdriver is used?
Xiaomi electric screwdriver
Bravo!
Gpu would literally chocking for sure
Выглядит круто, но на практике будет дико перегреваться.
There seemed to be plenty of room for some slims at the bottom
I would like to know, how are the temps in game?
would be very high considering literally no airflow
could two fans fit on the bottom, below the gpu?
2 120 15mm slim fans
Hello, I want to buy the safe in the video, but I could not find it.
thermal tests?
то что надо ) где бы его купить, дорогой зараза
Would this fit a Noctua NDH15 cooler on top of the CPU?
It won't fit in. SS135 is the best air cooler you can fit inside.
@@fuuneaki8729 Thanks!
K U B板😂😂，要極限不用ITX？還有一槽，極限條毛😂
实在看不出哪里极限，上面还有小粉红在酸
What is the case name?
這麼小 這規格會不會散熱不佳呢
散热肯定不行
这是要把显卡闷死么
Hi, which electric screwdriver do you use?
Where i can buy this case ?
I'd be interested to see thermals at during gaming...
temps ???
Can this motherboard handle full power of 13700k?
Yep
this is beautiful but in the case will be the hell degrees
Это самое лучшее что я видел в своей жизни
а где подача воздуха на вдув?
beautiful build and clean
4090算的剛好，看了真舒服
Your builds are awesome! subbed!
هذا صاروخ متحرك
بس فين الاقي الهيكل بيسي
Знатная печь. 😮
case model?
buen video
I love it man. I wish the video was longer
Очень стильно)
老哥我想問下你的12+4P訂製多長的
a very nice PC case but it cost a fortune.
$400-$800 as what I can see online.
What is the name of the case?
I never knew a pc building video could be so sexy
Cute heater.
what screw driver you're using ?
Bro skipped showing cable management after the 4 pcie gpu connectors where added 💀
Great ❤️👍
413 euro for a case ????? My louqe ghost s1 was 200 euro now is 150 … not worth it at all
at first i thought it was an mitx case 😞
Hello, my friend! Did you make undervolting for gpu and cpu for this little case?
OMG !!! Great PC
woow, very clean build, congrats
Should have a graphics card holder for peace of mind.
fantastic !
man I would love to make my build like this
我對螺絲起子很有興趣 , 是甚麼品牌型號啊
ok now, marinated chicken , and beacon is ready !!! ....let it Heat up?
Absolutely gorgeous
400 dollar SFF case is crazyyy
case is so expensive..😢😢😢
Что? 36 тысяч рублей за курпус?
这么大的箱子装个4090还算极限🤣，一般就差不多够了。
Beautiful mini system. Loved it!
这个线确实要理一下，其他的都挺完美。
that case is expensive as hell
Пока не покажут температурные тесты видеокарты и процессора в этом корпусе, он является красивым куском дерьма. Все будет очень сильно греться, вентиляторы будут гудеть на полную мощность. Я не рекомендую его к покупке без тестов.
“Скажи мне что ты абсолютно не разбираешься в сборке маленьких пк, не говоря этого” 😆
@@humanity_3 А ты самокритичный 😆
very nice
PSU is gets all the heat
what software u used and it that is an iPad?
34 in IDDLE and 98 in games.
Damn. I love it
一个是1000w的插头见你只是轻轻插入
一个是硅脂就涂抹的太业余了。毕竟满载近300w的U
显卡的风扇转速、噪音和温度表现怎么样？
CAN SOMEONE TELL ME WHY THIS CASE WHICH IS NOT A KNOWN BRAND COSTS ALMOST 400 DOLLARS?
naaa, bad idea😅
k系列+b系列🤔🤔
china 1 one!!! wa cao ni ma