#4.d - Configuring DCC-EX Wi-Fi @DriverDTrains
ฝัง
- เผยแพร่เมื่อ 9 มิ.ย. 2024
- @DriverD Trains #4.d - Configuring DCC-EX Wi-Fi
Welcome to Driver D trains. Thanks for stopping by! I’m your host Driver D.
Our conductor and brakeman Scratchy-C is… currently involved in a work stoppage.
[Meow]
In my last video, I showed you how to add a Wi-Fi shield to your DCC-EX command station, and use the WiThrottle app on your phone or tablet to run some trains. If you haven’t already seen that video, be sure to check it out!
** Adding Wi-Fi to DCC-EX - • #4.c - Adding Wi-Fi to...
In this companion video, I’ll show you how to configure DCC-EX to connect the Wi-Fi shield to your home Wi-Fi network, as well as how add an automation in DCC-EX to turn on your track power when the command station boots.
Both of these videos are part of a series on how to assemble and configure a DCC-EX Command Station to control your trains.
Videos in this series:
Part 1: #4.a - Assembling a DCC-EX Command Station - th-cam.com/users/videoHatlU7A...
Part 2: #4.b - Installing & Configuring DCC-EX - th-cam.com/users/videojv_xfwL...
Part 3: #4.c - Adding Wi-Fi to DCC-EX - th-cam.com/users/videoB08Qo0a...
Part 4: #4.d - Configuring DCC-EX Wi-Fi for Station Mode [**This video!**]
Part 5: #4.e - Adding and LCD Display to DCC-EX • #4.e - Adding an LCD D...
Part 6: #4.f - Correcting the Wi-Fi Firmware for DCC-EX [**Coming soon!**]
Chapters:
00:00 Welcome to Driver D trains!
02:41 Configuring DCC-EX Wi-Fi
03:48 Step 1: Connect DCC-EX to Home Wi-Fi
10:01 Step 2: Connect WiThrottle to DCC-EX
13:36 Step 3: Using AP Mode After Station Mode
15:16 Step 4: Restoring Access Point Mode
19:47 Step 5: Which Should You Choose - AP or Station Mode?
24:13 Step 6: Our First Automation
30:17 Additional WiThrottle Features
31:24 What's Next
32:18 End Credits
Products included in this video:
DCC-EX: www.dcc-ex.com
WiThrottle App (available on the iOS App Store): www.withrottle.com/
EX-WebThrottle App (Chrome browser only): dcc-ex.com/WebThrottle-EX/
Other DCC-EX Pages:
Wi-Fi Configuration: dcc-ex.com/ex-commandstation/...
EX-Rail (Automations): dcc-ex.com/ex-rail/index.html
What’s next?
In the next video, I’ll show you how to add a digital LCD display to your DCC-EX command station.
All aboard!
[Meow!]
DriverDTrains ©2023
![[TH] VCT Masters Shanghai Playoffs - Grand Finals // GEN vs TH](http://i.ytimg.com/vi/HL-hhLrtctw/mqdefault.jpg)
Hi. Enjoying your videos. Any chance of you using Engine Driver? It can do most of what WiThrottle full can do, but at no cost. Thank you
Just love these videos, especially the bits with ScratchyC in! Joking aside these are really useful videos and thank you so much for all the time you have taken putting them together.Well done indeed, and thanks again!
Thank you very much for the kind comments. I'm so glad you're enjoying the videos, and Scratchy-C always appreciates the love! I'm working on the video for the LCD display next.
Thanks again!
DD
Simply the BEST tutorial relative to DCC-EX Wi-Fi
Thank you very much for your kind comments. I really appreciate it. I'm glad you enjoyed the video. I'm working on one for the LCD display next.
Thanks again!
DD
Are you planning to produce tutorials relative to Automations ???
Again your videos are just the BEST.
Another Excellent Video, I learned quite a bit about setting up the Dcc-Ex to use the lan network. I have used it in it's simplest form, now I want to try doing it through my router. Thank you very much
Thank you again for the kind comments. Good luck getting your command station hooked up to your router! Just change the SSID and Password in the config file as I described, set the server configuration in your throttle app, and you should be good to go!
Thanks again!
DD
I was not aware of the +RESTORE command to restore the Wifi shield. Thank you. Another great video. More treats for Scratchy!
Thanks again for the kind comments and Scratchy treats. Glad I was able to share the +RESTORE command. Hopefully we don't need to use it too often. : )
Thanks again!
DD
@@DriverDTrains A video on a back and forth automatic script might be interesting. Scratchy the Engineer could take a break and just watch.
I really look forward to your content Driver D.
Thank you very much for your kind comments. I'm so glad you're enjoying the videos. The LCD display will be up next. When I'm done with the basic DCC-EX videos, I plan to do an introduction to JMRI.
Thanks again!
DD
Good afternoon. I don’t normally comment on TH-cam videos, but I wanted to take a moment and thank you for the series of videos. It is by far the best that I have seen as far as explaining the basics of DCC EX. Thank you very much! I do hope you still plan on doing a video about how to incorporate JMRI into the mix. I am new to this and trying to learn as much as I can. I have experience using raspberry pi boards on other projects, my understanding, is that you can incorporate a raspberry pi running JMRI with the Arduino running DCC EX for more functionality. I just recently purchased a raspberry pi Zero 2 W that I thought I would use in the model train, layout I am preparing to build. I don’t have a firm understanding of how all of this works. Anyhow, you had mentioned doing a video in the future about incorporating JMRI in a future video, but haven’t mentioned it in the last couple of videos. I am hoping you plan on still doing that. Thanks again this is a very informative series of videos.
Thank you very much for your kind comments. I'm glad that you're enjoying the videos. Yes I absolutely will be making a video about how to use JMRI with DCC-EX. Actually there will be a series of several videos on the topic, as there have been with DCC-EX. For starters they will mostly be about JMRI DecoderPro and setting up JMRI Throttles, as I don't have much call to use PanelPro yet, but I may come back to that later. And yes, you can run JMRI on a Raspberry pi, although I normally run it on my Mac.
I still have a couple of videos to finish on DCC-EX, including one about adding an LCD display which should be out soon, and one about how to flash the Wi-Fi firmware with he correct version for DCC-EX. Then I will start the series on JMRI.
Thanks again for your kind comments!
DD
Please return and post your next video. I enjoyed those videos released and wish for a new one.
Thank you so much for your kind comments. I'm glad you're enjoying the videos. I was quite busy over the holiday season but just posted my latest video, and hope to have more coming soon. Enjoy!
Thanks again!
DD
Good evening
I am following your DCC++EX video and I would like to know how to connect the DollaTek ESP-12E ESP8266 UART WiFi Wireless Shield for Arduino UNO R3 only in Wifi, I believe that in one of your videos there is the same but I don't see how to connect the two wires like in the picture. Thank you for your reply.
Hi, thank you for your comments. A couple of notes for you along with your answer. First, according to the DCC-EX website, DCC-EX does not support Wi-Fi on the Arduino Uno as it does not have enough memory. My understanding is that the compiler that loads the code onto the Arduino doesn't even try to load the code for the W-Fi onto an Uno. That's why I recommended the Arduino Mega in Video #4a.
dcc-ex.com/reference/hardware/microcontrollers/arduino-uno.html
"If you already have an Uno, or will use JMRI to control your trains, then by all means use an Uno. Just remember that you can’t have WiFi, Ethernet or a few other options due to memory limitations. But as a Command Station connected to JMRI with a USB cable it works great."
Now, if you have some other plans for the Dolla Tek Wi-Fi shield, the two pins you are looking for are the transmit (TX) and receive (RX) pins. These are in the bank of 5 pins that are bent flat at a 90 degree angle by the debug port on the top left corner of the board (this 5-pin arrangement is standard for UART devices). Remember, you need to connect the TX pin on the Wi-Fi shield to the RX pin on the Arduino, and the RX pin on the Wi-Fi shield to the TX pin on the Arduino.
Hope this helps and good luck!
Thanks again!
DD
Hello. Thanks for your video. I assembled a station like yours for the Märklin locomotive. There is a problem: after a couple of minutes of using Wi-Fi, the system freezes. This happens both through the home network and in station mode. Computer control works fine. The entire station freezes. The power does not turn off. There is no response from WiThrottle. Can you tell me what could be the problem?
Thank you for your kind comments. It sounds like the firmware on your WiFi chip may not be the version that DCC-EX works properly with. I am working now to finish the video on how to upgrade or downgrade the firmware to the DCC-EX compatible version. The version you want is 1.7.4. See "Step 1" in my community post at this link (be sure to click "read more" for the entire post) for instructions on how to check the version using the EX-Webthrottle app in Google Chrome.
Link: th-cam.com/users/postUgkxx7G_2R-TST_o0kEw6GOYHQry924iCGut
Good luck and watch for the firmware video soon. Thanks again!
DD
@@DriverDTrainsOk. Thank you!
Bonjour
Merci pour votre réponse, mais je ne suis que sur Arduino Mega et j’aimerais savoir comment connecter la carte wifi avec les 4 interrupteurs rouges. MERCI
Bonjour. Merci pour votre commentaire. Je n'ai pas essayé d'utiliser moi-même la carte Wi-Fi Dollatek, je ne connais donc pas tous les détails. J'ai trouvé cette page Web qui contient de nombreuses informations sur certains des problèmes liés à cette carte. Apparemment, il existe différentes versions de la carte qui fonctionnent un peu différemment les unes des autres. Vous pouvez découvrir quelle version vous possédez en regardant quels mots sont mal orthographiés sur la carte. Assurez-vous de lire les commentaires en bas de page. Il existe des liens vers d'autres vidéos montrant comment connecter la carte à l'Arduino. Regardez comment ils connectent les fils jaune et vert. Bonne chance!
www.instructables.com/ESP8266-ESP-12E-UART-Wireless-WIFI-Shield-TTL-Conv/
(Thank you for your comment. I have not tried to use the Dollatek Wi-Fi card myself, so I do not know all of the details. I did find this web page that has quite a bit of information about some of the issues with that card. Apparently there are some different versions of the card that work a bit differently from each other. You can find out which version you have by looking to see which words are spelled incorrectly on the card. Be sure to read the comments at the bottom of the page. There are some links to other videos that show how to connect the card to the Arduino. Look at how they connect the yellow and green wires. Good luck! )
DD
I'm an Android and windows guy so please tell me that you will go thru the Engine Driver Throttle program?
Thank you for your kind comments. I just released a video on using WiThrottle and Engine Driver with JMRI and DCC-EX and highlighted some of the basic info on how to connect Engine Driver DCC-EX as well. Check out Part 3 in the video for that. I may make a more in-depth video on how to use Engine Driver with DCC-EX (for example, to program decoder settings, etc.) in the future, but personally I much prefer to use JMRI DecoderPro for that, so it may be a while before I make that video.
Thanks again and happy railroading!
DD
Could you please show us how to Downgrade the software on those makerfab WiFi shields
Thank you very much for checking out the videos, and your question. I will be posting a video about how to downgrade the firmware soon. I am just finishing the video for the LCD Display, and the video for the firmware will be next after that one. You don't need an LCD to do the firmware, but it helps. In the meantime here is some information that might help you get ready.
Don't panic if it doesn't make sense. Order the part and I'll walk you through it all in the video.
* You need to order something called a USB to TTL Serial Adapter. It is $9 on Amazon. Here is the link: www.amazon.com/dp/B07D6LLX19
* Download the correct firmware:
dcc-ex.com/_static/files/esp8266/ESP8266_NonOS_AT_Bin_V1.7.4.zip
* Download the tool (Windows only; Mac doesn't use it):
dcc-ex.com/_static/files/esp8266/flash_download_tool_v3.8.5.zip
* Mac users will use the Terminal utility to install Python and run a python script.
This tells you how to install Python:
github.com/RavenSystem/esp-homekit-devices/wiki/Install-ESPTool-on-macOS
This has some information about the script:
github.com/DCC-EX/dcc-ex.github.io/pull/330/commits/83780f2782c0f4ae8a68b51ff9dbf149456f372a
* Read this how-to page to get an idea what we'll be doing (again the tool is Windows only, but everyone does steps 2 & 3, and some of step 4):
gist.github.com/nathankellenicki/7008540322c617869cec17226cff579d
It's very technical but not actually hard. I should have the video out in a few weeks.
Thanks again, and I hope you find the videos helpful.
DD
@DriverDTrains a friend downgraded the software, it worked for him. BUT when I power up and tell my android phone and android tablet the name of the WIfI Engine Deiver says it can't connect.
So I am finished. Done with trains as DC is not interesting to me. Deleted the facebook groups and the TH-cam videos. Deleted the discord software Engine driver EVERY THING!. GOOD RIDDANCE TO IT ALL.
'Promo sm'