Looks like a great place to start your fast trip to A&E to me! For less than three grand(VAT included), you can buy a brand new four post ramp with a four ton lift!
There are absolutely no parts in this thing to maintain. the one that you are talkign about has lots of seals and the seals go bad easily within few months. if you buy the cheap 3000 one.
each our product is tested with load 5000kg, that is more than 11 000 pounds. We developed the scissor lifts 20 years ago and we use only quality materials. China quality is poor and really dangerous . Very important is quality of material in gearboxes. Our product comes with our jackstands and uneven rails
@@1337penguinman To be honest you would have to be an idiot to get under there without any safety precautions I would highly recommend using axle stands in place when using this product.
@@DryUrEyesMate indeed always use telescopic car jacks that extend to the height of the vehicle while in the air or as you said it’s an accident waiting to happen
Can we add lumber under the lift to make contact with the car's frame instead of the rocker panels? I have an antique car with tires rocker panels or is the lift adjustable inwards towards the center of the car?
looks like a good concept but am not sure about the safety. so if you working below the front of the car and you don't want it to tilt down, does it have a locking mechanism?
@@Autolift-fm1qb Can your product work with an impact wrench, to turn the screw and make it elevate to lift the vehicle? Or will it only work with a rotary drill?
No way am I paying $1500 US for this. More like $500. I can buy a several hundred pound twin post car lift that lifts 9000 lbs and has a motor and pump for around $1800. There is just no way this 100 pound item has $1500 worth of material or engineering in it
It’s not how much watt you use but the nm power ratio the guy has said you need at least 35nm of torque required power to lift the stand so your usual impact gun should be just fine
You wouldn't get me under that thing on its own holding a car up. I'd see its best use to get a car up on 4 axle stands without too much faffing about moving a jack to each corner.
each our product is tested with load 5000kg, that is more than 11 000 pounds. We developed the scissor lifts 20 years ago and we use only quality materials. China quality is poor and really dangerous . Very important is quality of material in gearboxes. Our product comes with our jackstands and uneven rails
If the car is a ‘Front Engined’ but ‘Rear Wheel Drive’ (e.g. a BMW 3 series), do the gearboxes on the 3000 still go towards the front of the car? I’m assuming it’s the engine weight that matters, hence it’s only something like a rear engined 911 where the wheels have to point to the rear?
Hi, can you use 2 rise bars eithr side if you want to make sure your clear of a certain part or parts and if so how much and is the drill included in the kit and how much are they since 2016? Thanks.
Salut: moi depuis que j'ai découvert leur mini colonne de levage: @ je n'utilise plus que ça avec un jeu de chandelles qui montent haut pour la sécu et intervenir sur le train roulant bonne continuation
If you have a rear wheel drive vehicle then the position of the ramp would need turning around as the gearbox mechanism where the guy has placed it is in the front so in essence you need the gearbox mechanism at the back for this ramp hope that helps
j'en ai commandé un jamais reçu j'ai pensé que les commandes étaient bloquées a cause du covid. huit mois plus tard j'ai retrouvé une annonce sur pinterest donc j'en ai recommandé un et bien sur je me suis fais encore arnaqué cette fois j'abandonne.
Hi! Do you have contact information for this website? I paid for it for more than a month and haven't delivered the goods to me, and I didn't reply to any information sent to them. How did you contact them? thanks
Hi! Do you have contact information for this website? I paid for it for more than a month and haven't delivered the goods to me, and I didn't reply to any information sent to them. How did you contact them? thanks
For $450, every car guy will have one in the garage for $1500 most will spend the extra $400 to get a full size lift , I want one.
I couldn’t find this, so I bought the MaxJax Tilt which functions identically. I did a review in my channel, love this lift.
How much did the MaxJax cost?
Looks like a great place to start your fast trip to A&E to me!
For less than three grand(VAT included), you can buy a brand new four post ramp with a four ton lift!
If you have space
There are absolutely no parts in this thing to maintain. the one that you are talkign about has lots of seals and the seals go bad easily within few months. if you buy the cheap 3000 one.
Interestingly the best car tools and lifts are made in U.K.
Parfait, pour les bons bricoleurs exigent ! Ultra pratique et fonctionnel à souhait ... C'est merveilleux et pas cher ! Merci l'inventeur .
C`est de la camelote , oui . Même pas bon pour les bricoleurs .Trop cher et trop dangereux aussi .
Consider me an old safety bore but I will never crawl underneath a car resting on a lift like this.
Yeah, all it would take is one stubborn bolt and the front of that car is coming down on your head. I'll stick to good old fashioned jackstands,
each our product is tested with load 5000kg, that is more than 11 000 pounds. We developed the scissor lifts 20 years ago and we use only quality materials.
China quality is poor and really dangerous . Very important is quality of material in gearboxes.
Our product comes with our jackstands
and uneven rails
@@1337penguinman To be honest you would have to be an idiot to get under there without any safety precautions I would highly recommend using axle stands in place when using this product.
@@Autolift-fm1qb I would like to see this test that you claim with five tons do you have a video of this?
@@DryUrEyesMate indeed always use telescopic car jacks that extend to the height of the vehicle while in the air or as you said it’s an accident waiting to happen
Thank you for this video, nice information.
Can we add lumber under the lift to make contact with the car's frame instead of the rocker panels? I have an antique car with tires rocker panels or is the lift adjustable inwards towards the center of the car?
Thanks
I'd like to see him try that with a 40 year-old Morris Marina with crunchy sills!
Is it okay to lift a car like this, not using the designated lift points on a car? Won’t this damage the sills?
HOow is it a good height? You can not stand completely straight to do the work and you can not sit down as well to do the work.
Can this be adjusted as in the width of this lift.
I'm from Iraq, so please help me get this snake for the car and thank you for your treatment.
Why not make it so it lifts the car straight up. I dont see why it needs to tilt
looks like a good concept but am not sure about the safety. so if you working below the front of the car and you don't want it to tilt down, does it have a locking mechanism?
yeh nah. that looks wild and dangerous
Need me one of these!
Where did you buy the riser bars from
That's dangerous, you should support the front part of the car, any work underneath will force the front down due to the weight
I use a telescopic jack stand for safety
What keeps the riser bars from slipping on the main lift platforms?
rubbers on the platforms
@@Autolift-fm1qb Can your product work with an impact wrench, to turn the screw and make it elevate to lift the vehicle? Or will it only work with a rotary drill?
@@manofsan only rotary drill, ratchet or mechanical handle. The impact drill damages the gearboxes.
even at low and controlled speed?@@Autolift-fm1qb
Their website looks scetchy as hell. And people seem not to get theirs in months after purchasing if ever.
No way am I paying $1500 US for this. More like $500. I can buy a several hundred pound twin post car lift that lifts 9000 lbs and has a motor and pump for around $1800. There is just no way this 100 pound item has $1500 worth of material or engineering in it
That’s ok if you have the room. And height for a two post ??
Érdekelne az emelö.
Congratulations awesome presentation!
Thank you
@@Autolift3000UK where can I buy one in the UK?
they did not said nothing about 1,400 just 49.99 on market place.
Wish it was available in Canada 😕
Eu preciso comprar um desses onde consigo achar e qual o valor em média?
Donde se consigue
Hi i ordered one in early March but I have not received any response from your email as it says message box doesn't exist
Will this work on a bmw with them silly lifting points
Only good for small cars!
I have ordered 4 of these never got one
A lot of money for some tubular steel & not much else.
Which drill are you using in the video and where can I get one?
Weet iemand het telefoon nr hier van
hi, I would like to know which drill you use, because my 500 Watt electric drill cannot raise the car. how many Watts do you need ??? Thank you
It’s not how much watt you use but the nm power ratio the guy has said you need at least 35nm of torque required power to lift the stand so your usual impact gun should be just fine
You wouldn't get me under that thing on its own holding a car up. I'd see its best use to get a car up on 4 axle stands without too much faffing about moving a jack to each corner.
Where we can buy?
How much did you pay for it.
I want one! You send tô Brazil!?
I just found out my powerful Milwaulki SDS drill isn't man enough to lift my car! What is the make and model of your drill?
you need 2 speed drill or drill with torque at least 35Nm. You can use cordless drill Makita, DeWalt, etc.
I like Autolift3000UK but I cant see why its so expensive
each our product is tested with load 5000kg, that is more than 11 000 pounds. We developed the scissor lifts 20 years ago and we use only quality materials.
China quality is poor and really dangerous . Very important is quality of material in gearboxes. Our product comes with our jackstands
and uneven rails
@@Autolift-fm1qb where to buy in the USA
Me gustaría saber como se ase esa pies a para levantar
What about a using this kn a truck?
Yeah, I think I’m a sale. I’d like to more content
Can it be used on SUVs?
How much does it cost?anybody?
Hi where do you get the riser bars from ?
I use 2x4 or 2x6 lumber with mine... better grip.
If the car is a ‘Front Engined’ but ‘Rear Wheel Drive’ (e.g. a BMW 3 series), do the gearboxes on the 3000 still go towards the front of the car? I’m assuming it’s the engine weight that matters, hence it’s only something like a rear engined 911 where the wheels have to point to the rear?
The gearbox of the autolift 3000 can go towards the front of the car and also backwards. The important is centre of gravity
Hi, can you use 2 rise bars eithr side if you want to make sure your clear of a certain part or parts and if so how much and is the drill included in the kit and how much are they since 2016? Thanks.
Jenial
What is the lowest height. Have low cars so may not fit under
my buddy drives his onto a riser ramp before lifting the car
Salut: moi depuis que j'ai découvert leur mini colonne de levage: @
je n'utilise plus que ça avec un jeu de chandelles qui montent haut
pour la sécu et intervenir sur le train roulant bonne continuation
Rikco Etrop bonjour ou puige acheter ça et à quel prix svp
Boa noite sou Fernandes aqui de Irecê Bahia Brasil gostaria de saber como faço pra adquirir um peça como essa? E quanto custa?
Iae Fernando conseguiu compra já o produto
@@garagem2.5esteticaautomoti41 sabe onde encontro?
Is there any way to lock the pivot point thanks
Yes you can lock them.
please can you show us from where we can buy just worm reducer motor
I only import the complete lift.
What no link????
What is weight capacity of lift and is it available for sale in USA
6,614 lbs or 3,000 kg
@@cwclifford thanks
How much for 1 shipped to the US
T/ o
Hi Were Is possibile buy in Italy and how much Is it thanks 👍
www.autoliftproduction.com/it-it/
@@Autolift-fm1qb de donde es
@@miguelangeltanantadelaguil4631 United Kingdom
Combien vaut cette appareil
How does it cost
£1150
Quanto custa onde comprar
Posso sapere il prezzo
is it safe...if that slips your dead
Le prix svp?
Tell us please how many ratio has the worm motor
35Nm
Price
Onde posso compra um desse?
Halfords
Hello! I need one of those. How much for one?
£1150
Piece of overpriced crap.
Just find similar on Ebay for 440 pounds 🤣
Where do I buy one of these bad boys?
On ebay.
The only one I can find on eBay at the moment comes from Austria and costs €1,200 plus postage.
Mine cost £380 free postage
@@Golo1949 do you sell ratio motor I am interested on 2 reduce motors
is the Hilti SFC-22A cordless drill suitable for the lift?
I use a cordless Milwaukee so it should... (18v)
is this real?
Do you sell worm gear
I would NOT trust that even with my worst enemy
is this only good with fwd or can you use it with rwd vehicles
If you have a rear wheel drive vehicle then the position of the ramp would need turning around as the gearbox mechanism where the guy has placed it is in the front so in essence you need the gearbox mechanism at the back for this ramp hope that helps
Hi is it adjustable width wise
Up to a point, the supports are movable.
adjustable width
Official web: www.autoliftproduction.com/
Is it available in US yet?
yes
@@Autolift-fm1qb i order this and don't have a tracking number for delivery
@@adelaidafeliciano1702 please contact distributor
how much do they cost
£800.00 inclusive of VAT - you supply your own drill.
Mine cost £380 delivered.
@@Golo1949 hello where did you buy yours ?
Don't buy this on Instagram it's a scam
j'en ai commandé un jamais reçu j'ai pensé que les commandes étaient bloquées a cause du covid. huit mois plus tard j'ai retrouvé une annonce sur pinterest donc j'en ai recommandé un et bien sur je me suis fais encore arnaqué cette fois j'abandonne.
Hi! Do you have contact information for this website? I paid for it for more than a month and haven't delivered the goods to me, and I didn't reply to any information sent to them. How did you contact them? thanks
Did you buy the ezlift 3000 or the autolift 3000? Ezlift seems to be a scam in my opinion
Pelas Sancho yes
@@weiwencen748 which one?
En Perú cómo puedo conseguir?
Un contacto por favor
I ordered one no e-mail are nothing .
price
£1150
How much is it
$1450 on Amazon
Quero comprar um.
Hi! Do you have contact information for this website? I paid for it for more than a month and haven't delivered the goods to me, and I didn't reply to any information sent to them. How did you contact them? thanks
I also want to buy one, which website u contacted? Are u buying it from global website? What is your price offered?