How to replace the front wheel bearing on Suzuki Alto or Nissan Pixo
ฝัง
- เผยแพร่เมื่อ 25 ก.ค. 2024
- Welcome to the channel.if you still didn’t subscribe for our channel. Please do now. Also press 🔔 icon Then you can get our new video
I have suzuki alto 2014 model . Front wheel bearing noisy Because of that i will change front wheel bearing.
This job not hard. If you follow this full video? if you have the correct tool, I’m sure you will can do this job without any problems.
FOR TOOLS
SNAP RING PLIERS TOOL HEAVY DUTY amzn.to/3WZ8SqI
WHEEL BEARING REMOVE TOOL amzn.to/3VBOrPl
COPPER HAMMER amzn.to/3GgruMa
BAD WHEEL BEARING SYMPTOMS
Says by Will Herron
A wheel bearing is a group of ball bearings that enables a wheel to spin freely. The bearing fits snugly inside the hub of each wheel, and while it can withstand a lot of abuse, heat and water can cause severe damage. Most wheel bearings that are properly installed and cared for (regular inspection and grease) can last around 100,000 miles. But wheel bearing can suffer from neglect or damage from accidents and broken seals, and when they do it’s important to replace them. Failing to do so can cause further (and more expensive) damage to your drive axle and even result in your wheel completely detaching while you drive. Be on the lookout for the following signs of a broken or damaged wheel bearing.
Do you hear a rhythmic, rotating noise that gets louder at higher speeds? This may have something to do with your tires and may not primarily be the fault of your wheel bearings. It’s a good idea to check your wheels for patches if you do hear a rhythmic noise that increases in volume the faster you go.
Is the noise louder or softer when your car has more weight on one side or the other? You can test this by gently swaying your car while driving slowly. If the noise lessens when you sway right, then the damaged bearing is likely on a left wheel bearing. If it lessens when you sway left, a right wheel bearing is likely broken.
Does your steering wheel vibrate or wobble while driving? When bearings wear down they loosen inside the wheel, which can cause the looseness while driving. If you’re unsure whether your car has a wheel bearing issue, have an expert diagnose the situation.
If you have any questions, comment please mention below
Also please don’t forget to subscribe, comments, Likes and share this video
Good luck
Thank you very much
~-~~-~~~-~~-~
Please watch: "Step-by-Step Guide: How to Replace Wheel Bearing on Toyota Verso 2007 Front Left Wheel"
• Step-by-Step Guide: Ho...
~-~~-~~~-~~-~ - ยานยนต์และพาหนะ
Well done - clearly explained and good video - think this Alto may be the same as The Nissan Pixo - "Underneath the boxy bodywork, the Pixo is mechanically identical to the new Suzuki Alto it's even built by Suzuki on Nissan's behalf." perhaps you can get more hits if you include this in your title.
Thank you for your kind words and the helpful suggestion! Adding that information to the title can definitely attract more viewers. Here's a revised version:
"How to Replace Front Wheel Bearing on Suzuki Alto 2014 | Also Applies to Nissan Pixo - Mechanically Identical Models"
Including both model names should help those searching for either car. Thanks again for your feedback!
Great video
Nice detail video and DIY, although i do not have so many tools, specifically the Pneumatic ones to pull out the Bearing, generally we take it to the guy with Press Machine.
Thanks for a detail video.
With out proper tools bit difficult to do this job
Thank for the feedback
Two Side notes for you please. first, lower ball joint will shorten his life quickly working that way. second, the new nut should be used since this type of nut is crucial to replace each time you open cv axle for service. that why they add you new one as well circle clip. both are safety parts. if you see from your video you will see that the new nut is stuck at the beginning because it has "virgin" shoulder on top of it that give extra grip to the CV axle bolt.
Got you. Thank you very for your feedback
Really appreciated
It's my first time to replace front bearing, maybe i find it a bit harder. I'll come back to you sooner Bhai.
Shukria Bhai😊
Ok thanks
What model impact wrench you using
It’s Mac tool impact gun
Assuming you're based in the UK, how much (roughly) would this cost for a garage to do? I ask as the wheel bearing tool is expensive.
Yes I’m in Bromley
Around 140+VAT
Thanks
Hi what’s the name for removing or repressing wheel baring 😊
please check the description, all links are mentioned there, thank you
@@sanumotorswithcharlie 🙏🙏🙏
thanks you
How to change dicky shock alto indian 2015 model
Watch This Out. Specially made to your comment th-cam.com/users/shortsZuWHQtGwyT4?feature=share
Thanks