Tajima Embroidery Machine Stepper Motor Repair

แชร์
ฝัง
  • เผยแพร่เมื่อ 23 ธ.ค. 2024

ความคิดเห็น • 43

  • @robertopoma9565
    @robertopoma9565 6 หลายเดือนก่อน

    Hello friend, a question, my machine gives me the code 311, I removed the engine, do you have any idea how I can repair that part, what happens is that they tell me that I can only get used ones but they can give you the problem again.

  • @kodekubenini6163
    @kodekubenini6163 10 หลายเดือนก่อน

    Most useful information, thank you.
    I have the same issue with my Tajima Tmex c901 on the y motor. The machine loses registration at higher speeds or lond/wide stitches but only on the y axis. I think this is my solution.
    Do you perhaps have any ideas how to factory reset a Ricoma machine if you suspect a virus

  • @sadiqabubakarsaid4010
    @sadiqabubakarsaid4010 3 หลายเดือนก่อน

    Please I have same problem, can you help?

  • @keithsalazar2808
    @keithsalazar2808 9 หลายเดือนก่อน

    Where can i buy A new motor at?

  • @davidlacroix8496
    @davidlacroix8496 9 หลายเดือนก่อน

    fantastic repair approach....i could do this repair but i wonder what the probability of the Y axis motors failing together?...Y axis stopped working with the arrows on the control panel (and obviously when trying to embroider). machine doesn't throw an error code when motors fail? are the motors more of a probable cause?

    • @1981muldo
      @1981muldo  7 หลายเดือนก่อน +1

      @davidlacroix8496 No, the machines don't throw a code when the motors fail. Beats me as to why. There's only so many components in the chain and it's my belief that when the machine 'appears' to be working normally except for these axis failures, the motors are the most likely culprit but also inexpensive/cheap to try this solder repair. Yes, it's a lot of labour to take the machine apart and try this, but it beats throwing parts at it that might not be the problem. SO many techs go straight to blaming the x-y card. I think that's lazy.

    • @davidlacroix8496
      @davidlacroix8496 7 หลายเดือนก่อน

      @@1981muldo in our case I was able to find two motors for $179 a piece brand new the tech could only find $700 Motors
      Perhaps my 35 years in the Auto industry has helped me locate the correct parts
      I will take these motors apart and check the connectors and repair them, keeping them as spares

    • @juniorgee500
      @juniorgee500 26 วันที่ผ่านมา

      @@davidlacroix8496hey bro by any chance ce can you help me find a XY card for tajima tmex c1501? Thanks in advance

  • @Rustysgsxr
    @Rustysgsxr ปีที่แล้ว

    Do you happen to have knowledge about the pulse stepping motor for the upper thread hook? Our hook doesn't seem to pop out far enough to grab the thread "consistently". Upon removing, we noticed the shaft does not go forward the same amount as it go backwards. For example travels clockwise 1/4 " but then goes counterclockwise 1/8". Does that mean it's bad?

    • @1981muldo
      @1981muldo  ปีที่แล้ว

      I'm sorry, I can't say that I've had to delve into that particular stepper before. Honestly, most of the trimming and wiper (the hook you speak of) problems I've had are due to tension being too high.

  • @charleswilliams6114
    @charleswilliams6114 2 ปีที่แล้ว

    Hi. Thank you for your instructional video extremely helpful. I have a similar problem and I would greatly appreciate your input in resolving this. I ha Tajima 2000 TMEX c-15. Lately it decided not to work. When I turn on the machine it starts embroidering in the same spot (won’t wait for me to upload a program). The only way I can stop is by turning it off any ideas what coulee wrong with it. Will appreciate your assistance. Regards Charles

    • @1981muldo
      @1981muldo  2 ปีที่แล้ว

      Doesn't sound quite like the same problem. I think you may have issues with your main controller. I would try re-loading the firmware (factory reset the machine). If that doesn't fix it....

  • @marvinquinit4706
    @marvinquinit4706 ปีที่แล้ว

    I want to do this on my machine for my X axis motors, I'm not sure how to remove the motor shaft off bearings that hold it all together. Any tips would be appreciated. thanks for the video.

    • @1981muldo
      @1981muldo  ปีที่แล้ว

      Bearings will be a tight fit but should come off. Pulleys will have two set-screws in them you’ll need to loosen before they’ll slide.

  • @joefish1498
    @joefish1498 2 ปีที่แล้ว

    That breaker box is priceless!

    • @1981muldo
      @1981muldo  2 ปีที่แล้ว

      Actually they're only a couple hundred bucks, depending on how fancy you go. This one is 40 years old.

  • @jamesemanner9671
    @jamesemanner9671 4 ปีที่แล้ว

    Great instructional video! My only question would be, why did the pin get hot in the first place? Do you suspect it was a poor joint on the PC board (header), or possibly the connector terminal?

    • @1981muldo
      @1981muldo  4 ปีที่แล้ว +1

      @Jim Manner I have no idea. That particular motor with the burnt pin was actually a spare motor that came with one of my machines....turns out it was 'spare' for a reason. I do think, as you also suspected, that it was the corroded/poor joint on the PCB that caused an excess voltage drop and consequently a hot pin.

  • @kozzimo55
    @kozzimo55 3 ปีที่แล้ว

    Great video. I have a very very similar issue with my X-axis and I feel like I have tried EVERYTHING. Is there a way I can contact you? I would love to figure out what my problem is.

  • @mikeharper4503
    @mikeharper4503 ปีที่แล้ว

    Can you suggest a source for buying replacement y-axis stepper motors for my TEHX-C1501?

    • @1981muldo
      @1981muldo  ปีที่แล้ว

      Not yet...it's on my to-do list.

  • @thomasclancy6215
    @thomasclancy6215 ปีที่แล้ว

    Great video.

  • @rosuelmartinez9700
    @rosuelmartinez9700 ปีที่แล้ว

    I have a machine that is shifting my design left to right...up and down it's fine it seems to be jumping out of place when it goes left to right...any suggestions?

    • @1981muldo
      @1981muldo  ปีที่แล้ว

      This could be the same issue. When these motors lose a leg they become unpredictable until they start failing more often then you see the complete loss of an axis.

  • @jtlooksharp
    @jtlooksharp 3 ปีที่แล้ว

    @muldo the X axis on my Tajima TMEX-C1201 just stopped working entirely out of nowhere. When it's off I can move it freely; it's not jammed or anything. There are no errors being thrown. When I push the L/R buttons at first I thought nothing was happening, but I just realized it's humming and vibrating VERY slightly. Do you think I should start by replacing the motor? It doesn't have the same connections as in your video; there are no solder points to be bad. Are you pretty sure about the NEMA 24 thing? Thanks SO MUCH for recording this video at 3am :-D

    • @1981muldo
      @1981muldo  2 ปีที่แล้ว

      Sorry I missed this comment...... Yes, sounds like a similar issue. I'd crack the motors open and re-solder the points and see if it works. Nothing to lose.

  • @sharonsmall7883
    @sharonsmall7883 3 ปีที่แล้ว

    Hello, my TEJT 1501 2005 MODEL has a problem. when its turned on, the frame moves around to find the origin, but the pantograph doesn't complete its cycle. CHECK X or Y pulse motor is the error, therefore the machine cannot function. Do you think your tutorial will help?

    • @1981muldo
      @1981muldo  3 ปีที่แล้ว

      Hi Sharon; I'm not sure. That doesn't sound quite like the same issue. This may or may not help. The TEJT's are more similar to the old Toyota's as far as I'm aware...might want to ask this in the Tajima/Toyota facebook group. There's some techs in there with better experience on those machines.

  • @jenniferbaria8808
    @jenniferbaria8808 2 ปีที่แล้ว

    How can I contact you? My machine has the same exact issue and I am following your video but cant figure out how to remove the motor from the back of the bar.

    • @1981muldo
      @1981muldo  2 ปีที่แล้ว

      Hit me up on facebook. Link in bio. I'll help if I can.

  • @vinizuh
    @vinizuh 4 ปีที่แล้ว

    Hey great video man, appreciate the time and effort making this tutorial. I have same issue with Y axis on a single head tajima tehx-c1501. The Y axis would stop moving and it would correct itself if i power cycled the machine. But eventually it just stopped working. Did this method fix the problem?

    • @1981muldo
      @1981muldo  4 ปีที่แล้ว +1

      @vinizuh hey thanks. You know, all I can tell you is that my machine hasn't had the pantograph glitch since. I think that only time will tell, and so far so good.

  • @uniquedesigns5223
    @uniquedesigns5223 4 ปีที่แล้ว

    I have the samae issue for the y axis motor. It just sews back and forth left to right every 10 to 15 jobs. Did it end up being your motor

    • @1981muldo
      @1981muldo  4 ปีที่แล้ว

      So far so good. No glitches since this solder job.

  • @alisadavis9916
    @alisadavis9916 2 ปีที่แล้ว

    I have a 2010 Neo2 that is having intermittent 316 main shaft motor issues. I just ordered a main shaft motor on a Net 30. Is this motor also a stepper motor, or is the fix the same or similar? I think I could make this fix if it's the same. I don't think the motor ever got overheated.

    • @mikeray2782
      @mikeray2782 2 ปีที่แล้ว

      had the same issue ,there is a magnets glued on the shaft inside the motor that came unglued

    • @1981muldo
      @1981muldo  2 ปีที่แล้ว

      Oh hey Alisa! I think we already chatted about this over on FB. Did you ever get it going??

    • @alisadavis9916
      @alisadavis9916 2 ปีที่แล้ว

      @@1981muldo yes. I bought a new motor and my tech installed it. Works better than when it was new

  • @rataestudio6274
    @rataestudio6274 2 ปีที่แล้ว

    Hi men, i have a melco emt16 & i want to change the stepper motor X for another generic.. would you help/guide me on "how or what model" could use? The f@#kers doesn't give any specs. It's a 3xmotion 6 coil motor. And i can give you the "sticker" data (beside of pics or any other possible data). If it doesn't is to much trouble for you

    • @1981muldo
      @1981muldo  ปีที่แล้ว

      I’m sorry I don’t know much about Melcos, internally anyway.

  • @jerryleejohnsonjr1377
    @jerryleejohnsonjr1377 2 ปีที่แล้ว

    did it work? let us know, i have the identical issue
    great video!

    • @1981muldo
      @1981muldo  2 ปีที่แล้ว

      So far so good.

  • @nengonengo7772
    @nengonengo7772 2 ปีที่แล้ว

    Hello