Thanks for this! I have the same model, and it's giving me a pop and some resistance when adjusting the height. Thanks to your video, I'm a little more confident in opening her up to take a look around 👍
Hi Peter .. can I know what’s dust collector HP or brand name attached to planer ? I have DW734 and looking for good dust collector at reasonable price
Hi there! I’m using a 20 year old Grizzly dust collector. Its similar to this one that they currently sell. www.grizzly.com/products/grizzly-1-hp-light-duty-dust-collector-polar-bear-series/g1163p I use it for my Table Saw, Planer & Jointer. I connect it to each tool with a 10 foot hose with slip on connectors on each end. It does a good job. Thanks for watching!
Motor was running well before tuneup. No strange noises or vibrations. Can you share how someone would check the motor for proper operation? Thanks for watching.
@ I’ve honestly no idea, I was curious, recently got ahold of my grandfathers dewalt dw743 planer over thanksgiving and came across your video, I got it working
Hi! Thanks for watching. Dust collection is an issue for me as well. For my smaller tools(routers, mitersaw, sanders, etc.) I use a Rigid shopvac hooked up to a Dust Deputy cyclone separator. For my larger tools (Table saw, planer, jointer) I use a small 1hp dust collector with 4” hose. Both systems are just ok capturing maybe 90% of larger grained sawdust. The fine dust still goes everywhere.
Just a note, don't remove the four screws holding the side panels to the top cover. Just remove the cover screws and the side panels will lift off with the cover. Eliminates breaking the side panel screw holes.
Hard to say what went wrong. Its probably best to go back in and make sure all blades are installed correctly. Also, maybe check belt to verify its correctly seated. Good luck.
what was the issues when you replaced the belt? I have been having this clunking noise in mine , while on even with nothing running through. It i feel like it would make sense if it was the gear or belt system. the piece of lumber stop and goes and leaves roller marks on the piece almost like the roller is getting pressed harder at one point in the every rotation of the roller.
Thanks for watching. The issue I had with the belt is it started to fail while planing some hardwood… specifically white oak. The belt was very old and broke apart while planing. I suggest changing out belt if its very old.
Got one for $60 today. Rust on the supporting columns, a lot of gunk and old saw dust and it doesn't turn on. Upon checking, its missing the motor brushes. Hopefully those are the only reason why it won t start.
I really needed this video. Thank you.😊
Thanks for watching!
Excellent video! Thank you!!!
Thanks.
Glad you liked the video
Great video with much needed information. Now I can tune my DW734 after watching this.
Thanks
Glad you found the video helpful.
Thanks for watching!
I acquired one of these yesterday for free and it needed a lot of work. This helped simplify the process. Thank you, much
Free??? That’s awesome!
The DeWalt DW734 is a great little planer once it’s tuned up. Glad you found the video helpful.
Thanks for uploading this, have struggled to find stuff to help me with problems with the model. Loving the videos lately!😊
So glad you found this video helpful.
Thanks for watching!
Extremely well done. I will be using this to refurbish my own 734. Thank you!
Thanks for watching. Glad the video was helpful to you. 👍
Thanks for this! I have the same model, and it's giving me a pop and some resistance when adjusting the height. Thanks to your video, I'm a little more confident in opening her up to take a look around 👍
Thanks for the feedback.
So glad the video helped!
Great information Pete!
Just chances my blades after i watch your video on u- tube…😊
Great! So glad the video was helpful.
Great! I've been looking for a video like this, thanks
Glad you found this video helpful.
Thanks for watching!
I will be buying one of these used from cabinetmaking instructor.
Good for you.
These are great machines that will last for decades if well cared for.
@@PetefromBaltimore Thanks I think I am going to start a TH-cam channel on setting up a cabinet shop in my one car garage.
Good video. The broken plastic bits may make the machine buzz or rattle. I'd epoxy them back in place.
Thanks for the feedback.
And thanks for watching.
Hi Peter .. can I know what’s dust collector HP or brand name attached to planer ? I have DW734 and looking for good dust collector at reasonable price
Hi there!
I’m using a 20 year old Grizzly dust collector. Its similar to this one that they currently sell.
www.grizzly.com/products/grizzly-1-hp-light-duty-dust-collector-polar-bear-series/g1163p
I use it for my Table Saw, Planer & Jointer. I connect it to each tool with a 10 foot hose with slip on connectors on each end. It does a good job.
Thanks for watching!
Should you of checked the motor as well?
Motor was running well before tuneup.
No strange noises or vibrations.
Can you share how someone would check the motor for proper operation?
Thanks for watching.
@ I’ve honestly no idea, I was curious, recently got ahold of my grandfathers dewalt dw743 planer over thanksgiving and came across your video, I got it working
What do you use for dust collection? I make wood/epoxy cutting boards and I can’t seem to figure out what is best for dust.
Hi! Thanks for watching.
Dust collection is an issue for me as well. For my smaller tools(routers, mitersaw, sanders, etc.) I use a Rigid shopvac hooked up to a Dust Deputy cyclone separator. For my larger tools (Table saw, planer, jointer) I use a small 1hp dust collector with 4” hose.
Both systems are just ok capturing maybe 90% of larger grained sawdust.
The fine dust still goes everywhere.
Just a note, don't remove the four screws holding the side panels to the top cover. Just remove the cover screws and the side panels will lift off with the cover. Eliminates breaking the side panel screw holes.
Thanks for the tip!
And thanks for watching.
What size screws for the dust port?
This is alot simpler than expected
Glad the video was helpful
I saw your video. Hope you can help me . I changed the blades I turned it on and it shakes so much the screws on the metal table vibrate off
Hard to say what went wrong. Its probably best to go back in and make sure all blades are installed correctly. Also, maybe check belt to verify its correctly seated. Good luck.
what was the issues when you replaced the belt? I have been having this clunking noise in mine , while on even with nothing running through. It i feel like it would make sense if it was the gear or belt system. the piece of lumber stop and goes and leaves roller marks on the piece almost like the roller is getting pressed harder at one point in the every rotation of the roller.
Thanks for watching.
The issue I had with the belt is it started to fail while planing some hardwood… specifically white oak. The belt was very old and broke apart while planing.
I suggest changing out belt if its very old.
Got one for $60 today. Rust on the supporting columns, a lot of gunk and old saw dust and it doesn't turn on. Upon checking, its missing the motor brushes. Hopefully those are the only reason why it won t start.
Hopefully you can get it up running.
Its a great little machine when it’s set up well. Good luck!
Never even leveled the bed