Programming your Sentry, Sherlo or E.T. remote controls

Riaan from Yale Security Point in Brooklyn shows you how to easily pair your Sentry, Sherlo or E.T. remote controls with their corresponding receivers.

[@miguelbento3474]

Brilliant, perfectly explained, just what I needed! Thanks :)

[@phemelophiri2863]

2023
Thank you ..

[@leeryan8287]

Thank this saved me a called out fee simple and straight forward. Thanks!

[@waltervanlille2263]

Dankie baie.. Dit was n groot hulp vir my..

[@franspretorius3982]

Thanks for the guidance, really helpful👍👍

[@mielie0071]

Dankie man. Dit het baie gehelp.

[@sandilenxumalo4709]

thank you very much, this video made it easy for me to programme my remote in a minute

[@daviddutoit3202]

Thank you! This saved me a whole call-out fee just to get the remote programmed!

[@Ice2Eskimos]

Wow! You made it s easy! Thank you!!! Did it a few seconds!

[@metaearthtechnology1611]

THANK YOU . YOU THE BEST!!!!

[@neil_digital]

Thanks so much for the video

[@terencebenjamin3382]

Nice illustration is there one for the gate motor ped setting?

[@Dylanscam1]

Thank you...

[@YunnydP]

Dankie man!!!

[@douglassouthern6368]

Hi Riaan. How do I program a 1 button Sentry with dip switches to a sentry 3 button without dipswitches. Obviously I only need to pair one of the buttons on the 3 button.

[@dawiemalan2705]

I have an ET remote, but the light on the receiver does not even light up when I press the new button on the remot and short it with the pin on the P button?

[@Man-Kev]

How do I re-program the RX3 - RC (3 channel) Alarm system, to ensure a lost remote control does not operate IDS Alarm? Seems that the receiver is from Centurion RX. Please send steps or link where i can see a nice step by step procedures. Thank you!

[@kanephu]

Please help. i want to program a ET remote to a centurion receiver, i did try wht onthe vid and it is not working.

[@louisgouws5680]

What remotes can be paired with the sherlo

[@WayneErradu]

How do you programme a 4 button Sherlo remote?

[@JC-bn1cu]

How do I reset the sentry ??

[@kmashishi]

Thank you for the video i managed to add a remote, but now with the new ET remote i have to press it twice before it opens and i have to also press twice before it closes. What could be the problem?

[@aspidus325cchomesecuritymo5]

U programme ur remotes with latch pin in

[@aspidus325cchomesecuritymo5]

Default and programme with all pin out but only programming one in

[@deanvanderweshuizen7146]

You must remove the connector from the pins

[@sherlotronicssouthafrica8927]

Please note the second receiver is not a sentry as was called in the video it is a Sherlotronics Receiver.

[@ashmiermaged3126]

Hi when my neighbour press their garage remote my et gate motor pedestrian open what could be the problem

[@aspidus325cchomesecuritymo5]

Hi, the time u program your remote they also pressed their remote trying to open their door and was stored on ur motor because ur reciver or ur motor was on a programming mode. U need to default ur reciver and reprogramming ur remotes

[@annatjiedebeer4109]

How do I re-program the ET system, to ensure a stolen remote control does not open the gate?

[@mbikisha]

Press the program button for 10 seconds until the light flashes the memory will be cleared, then program all your remote from start.

[@aspidus325cchomesecuritymo5]

U need to default the motor to erase everything and programme ur remotes again

[@natashabowman3509]

Hi my sliding gate does not want to close what might be the problem

[@aspidus325cchomesecuritymo5]

Check power and battery and if they are ok then u need to call a technician

[@karenvisser4537]

how do i link the pins in the 3rd example? note my pins are old and dusty haha

[@libertymuneri5384]

E. T system gate motor

[@libertymuneri5384]

Am struggling, how to program the runtime limits