This video explains step by step procedure of how to Configure Open shortest path First(OSPF) routing protocol which is internal (Intra-domain) routing protocol using cisco packet tracer
I'm very happy by seeing your vedios of Cisco packet tracer mam because ours lecturers wont explain good like u that u explain . Thanku mam for good preparation for exams
Thank you for the video. the explanation was very crisp. Could there be more explanation on commands as beginners find it difficult to understand the purpose of the command
Their are ,3 modes in CLI and all this commands doing in 3rd mode , for doing first enter en( enable ) it set u in 2 nd mode after config ( configuration) u enter in 3 rd mode . This ospf protocol command done in 3rd mode of router . Thanks u
I'm very happy by seeing your vedios of Cisco packet tracer mam because ours lecturers wont explain good like u that u explain . Thanku mam for good preparation for exams
Thank you for the video. the explanation was very crisp. Could there be more explanation on commands as beginners find it difficult to understand the purpose of the command
Ssit students attendence -->
Very well explained. Finally understood ospf
Are u Run the network on software ? 😂😂
@@educationsingh2038 I don't know if you were attempting to roast me, but I didn't understand shit cuz my english ain't that bad brother. Do better.
thanks!! you saved my life and dignity!!! Love u
this lady is legit, listen to her
Thank you so much for beautiful exaplannation, it was very helpfull.😃😃😃
Nice explanation... Good introduction to ospf using "Cisco packet tracer".
Thank you so much...You made it very easy.
Great explanation for the practicals . Just a doubt does ospf really care about the number of routers or the cumulative interface cost
wonderfully explained mam! thankyou!!
Bundle of Thanks mam❤
Hello MAM you told in ospf brief, OSPF work in autonomous system but ospf doesn't work autonomous system, It use process id and area only.
Thanks for your effort of helping us
You are the best madam ❤️❣️🤝🤝🤝
bravo! very good explanation about how to set up a network inside an autonomous system
Madam in CLI while we are doing with the commands is there any sequence of the routers
This is a great video,
Best explanation
Excellent MAM. 🌹
Excellent ... well done ...
nice explanation but I could not send from ROUTER2 to PC1 could you explain me plese ?
in router configuration in packet tracer 6.2 I have an error in CLI. It can be solved typing
enable
configure terminal
Superb explanation
Their are ,3 modes in CLI and all this commands doing in 3rd mode , for doing first enter en( enable ) it set u in 2 nd mode after config ( configuration) u enter in 3 rd mode . This ospf protocol command done in 3rd mode of router . Thanks u
Is it mandatory to implement OSPF in CLI? Is there no interface?
thank you professor
thank you very much
hi thank you, should I give static route? ping itt does not reach from pca to pcb only def. gateway.
Please clarify the use of Product Id number and area number and when it change?
I'll see you in heaven 😂♥️
TQSM madam
nice
Hii mam I have some questions about framerelay eigrp ospfipv6 etc could you explain it please respond
thank you
NICE!!! 👍
thank you maam
THANK YOU
thankyou thankyou thankyouuuuuuu
It’s very lengthy process and I know the shortcut
Thanks mam
Showing in CLI invalid input detected at '^' marker while writing networks. Why?
in which mode you are
config mode?
enable
configure terminal
What does area0 mean?
You could have used RIP instead of CLI, that would have been easier.
But Thanks for you efforts, you helped us a lot
But then you would not be using OSPF routing protocol but RIP instead.
thank
Area0?
ok I put a third pc too
thank u