CUSTIS programming using DIY. USB-RS232 cable and 1314 software (** Google Drive download)
ฝัง
- เผยแพร่เมื่อ 18 ต.ค. 2024
- Setup with DIY cable much cheaper than buy the factory cable which cost almost 500 UsD but this cable only 10 USD...
Download Programming software here: New LINK on Google Drive
drive.google.c...
#ProgrammingCable #ElectricGokart
You, sir, are the hero we didnt deserve.
Thank you my friend,your video helped me to solve my problem.I hope the best.
You are a genius
awesome video...do you need the pre-charge resistor for programming on the bench? You mention it, but it's not shown in the video...
Thanks for the video. the DIY cable works for me. save me some $$.
LINK TO SOFTWARE and Cable drive.google.com/file/d/1U9IwknqsoYL9o8UlDQVZtsimC3h-Sztf/view?usp=sharing
Link worked for me and software works with blue USB to FDI type cable and chip with no modifications.. THANKS!
That diagram was originally drawn by me back in 2012..... Additional info .... NOT ALL makes and models of USB-Serial adaptor leads work.
I recommend using a USB-Serial adapter that uses a Chiphead chipset e.g. CH340 /CH341
Did you use rs232 levels or TTL levels?
@@georgegriffith7599 There's a crazy long forum post on buggies gone wild about 'programming curtis controller'. Looks like it's pretty obviously RS232, though. The power lead is 15V, that's a dead giveaway. RS232 is 15V, and there's no way anything TTL would have volts that high.
@@joesanchez2465
Hi, how in the world can this idea connect to a 1205-117 controller? I bought the cheap ch340 also got a breakout and a molex and everything I do fails.. all I need is this controller to be ITS then I will trash all of this..
I have 36v and also 36v on the j1
I'm running this software that's in the video wired the exact way all I get is the "can not reset the usd.. or can't detect?? Help
did u find a solution to this?@@carlton997
I saw a long discussion on Buggies Gone Wild where they seemed to indicate TTL levels were required. You said TTL didn't work. So, that means you used RS232 levels? What USB to Serial adapter did you use?
A great video. I have subscribed. A quick question. Your blue/yellow/black colors appear to be standard. I bought the usb-serial adapter and a straight-through serial cable. I cut the male end off the serial cable. Pin 2 of the female was yellow. Pin 3 was blue. On both the female and male ends of the serial cable. This is backwards from the colors you used. Is there a reason for this? On my cable, I would run the yellow from pin 2 of the adapter to J3-3, and yellow from pin 3 to J3-1?? What happens if I get them backward?
Ur TX rx would just be backwards nothing would happen you just need to swap around.
It goes from transmit to receive and receive to transmit,,,Plus a ground! So from USB cable pin 1 is ground, Then pin 2 of controller is ground ,, pin 3 of USB (transmit )to pin 1 of controller , pin 2 receive of USB goes to pin 3 of controller.. Worked for me... got to change perimeters and monitor the controller... i know your comment is a year old but in case anyone else needs to know
On the sheet at the start of the video you have the DB9 connector REAR VIEW. Below it you have a picture of the DB9 from the front. The pinout is the same for both. What gives?
hi, you can connect a CURTIS 1232 or 1234 with that cable ? thank you for the video
YES i did it recently worked out great...I used the blue cable...not a standard rs232 but one using the FTDI chip ,, look up this description..
DTech USB to Serial Adapter Cable RS232 DB9 Male Port with FTDI FT232RL Chipset Supports Windows 11 10 8 7 and Mac Linux (1.5 Feet)
@@chuckthebull thank you..! I'm goint to try it.. 😀
Gracias
Parabéns pelo vídeo, fiz aqui e deu certo, comunica de boas com o controlador. Obrigado!
Amigo compartilha o software comigo por favor , o link do vídeo está off.
Do you have the instructions about configuring the settings within a Curtis 24 volt battery charger with the same 1314 software?
drive.google.com/file/d/1XLtdl8vtZ6Nzf3BhpbDeqyJhAgml6_6F/view?usp=sharing
Can anyone point me to the CURTIS program for the 1243-4209 motor controller?
Or
the electrical/electronic diagram of these controllers?
Do you need any drivers to find your curtis? And does this settings apply to jwdawn?
Hi sir. Is same method will work for other controllers (1239e) also ??
The 1219-8406 module is it possible to communicate with this cable and soft?
Gracias por actualizar el archivo
Any idea if this method will work with curtis 1239e controller ?
Will this work with Curtis controller 1206hb?
Aprs packet in the background 😀
Has anyone figured out the :USB CAN Adapter: unable to reset USB?
any link on where to get plug for controller?
Sir double drive ki video wala link mil jaayega kya please
Download link doesn't work 😅
tambem preciso
Vocês voces conseguiram o software ?
Hi how we can contact I have some problem with controller 1232SE
What’s the max speed you can set it too?
depend on what size of Battery it can be set as percent of acces..
can you update the link to the software please ? this link is dead
drive.google.com/file/d/1XLtdl8vtZ6Nzf3BhpbDeqyJhAgml6_6F/view?usp=sharing
Sorry About that , This project already out of date but I already put the new download site
What I get is "USB CAN Adapter: unable to reset usb adapter". Any ideas? I have 36V on B+ and B- and key switch to B+. Software in a laptop and usb-serial adapter to the pins on the 4 pin molex on the curtis.
Same problem, maybe 24v. Did you figure out the problem, and how did you solve it?
Hello, greetings from Chile, I have the same problem. any ideas?
@@campoint.x1032 Hello, greetings from Chile, I have the same problem. any ideas?
@@heroesinnombre Ok this happen to me. Just pull the J1 one wire. The one that get power from your key. Make jumper that will go from J1 to your main bat bank. You need all 36 volts going to it. Then plug in the computer. See if this works.
Hi. I am trying really hard to build an old ezgo txt and I need to change to ITS. I bought the pass through and a rs232 ftdi and all I get is "usb can adapter: unable to reset USB adapter. Any help? I have 36 volts and a jumper from F1 to battey +
Hi could you share the wiring diagram showing the pin number connection on the serial port?
Wel , If you watched video at the beginning you can Caption screen or pause it to see the Diagram
hi . I can't connect it
Hola, alguien sabe donde puedo descargar el programa? el enlace está caido.
tambem estou precisando
Eu tmb
lo consiguió? yo aún lo necesito@@angelopontes3065
ขอเบอร์ติดต่อพี่หน่อยคับ