Hello there! I just got a Fender Bassbreaker 30 and it comes with a 2 button footswitch. The amp has 2 channels and a high gain button to drive the dirty channel even more. On the foot switch, button 1 changes from clean to dirty and button 2 enables the high gain for the dirty channel. When I connect my insert cable into triggers 1 & 2, the amp seems to only switch between clean and high gain, not allowing me to access the dirty channel on the amp without the high gain engaged. Any idea what combination of trigger configuration/different cable routing options might work in this case? Much thanks!
Hello, I've just bought a PXL PRO in order to control the channels in the Joyo Mjolnir but it doesn't work. The amp doesn't recognize the controller. I noticed that the cable which came with the amp is in stereo and the PXL PRO triggers are in mono. So I decided to get a stereo cable with one stereo connector and two mono connectors and it controls the distortion channel but not the clean. Can you help me please to solve this problem.
Hi would the triggers work with an vox ac15ch ? To switch between the normal and top boost channel. ( A 1/4" from 1 trigger to normal channel and 2nd trigger to top boost channel) ? What I'm looking to do is for eg. Have distortion pedal on in normal channel , and then with the press of a button switch to top Boost channel with distortion pedal off. Thanks Mark
In theory that should work fine, as long as your amp has a foot switch input (which most modern AC15s do). You would then connect the JOYO to the foot switch input. I'd check with VOX to be absolutely sure it will work though.
Hey.i am using a dsl 100.only one channel switch possible. I plugged in in trigger 2 and i see there is the green light at the amp but it jumps back to red quickly.so i cant use the the overdrive channel. Is it possible that i have to use a stereo cable instead of a mono cable? The footswitcher has a stereo cable?
Thanks for the video! I'm new to this sort of stuff - is this using Control Voltage to change the channels? I ask because I have an Empress Echosystem that can receive control voltage of 0-5 volts to change knob settings, wondering if this would work for it?
Depends on how the channel switching works. If it cycles through the three channels two would be enough. If each requires a separate trigger then it won't.
thanks for sharing the vid. i'm pretty stoked on the PXL looper, and curious what pedalboard you have it paired with here. wanted to pair it with the Accel XTA21 but the swithcer tray is a little too narrow (20" vs 22" Joyo PXL). thanks again
I got a Peavey triple X head and I bought a custom made cable that splits the seven-pin footboard pedal output into three 1/4” jacks to plug into three of the trigger inputs of the Joyo Pxl Pro’s four trigger inputs. I’m having difficulty programming channel 1A to be set to the ultra channel on the Peavey Head and channel 1C to switch to the clean channel. It seems that when I correctly set it up for channel 1A, having the polarity on only for trigger 1, then program channel 1C, having the polarity on only for trigger 2, it wipes out my polarity saved setting for channel 1A setting it so only trigger 2 polarity is on preventing me from activating the distortion channel when I switch back to 1A.
Hi there. That's not something I can help with unfortunately. I doubt that either the Peavey or the JOYO have been designed with this configuration in mind. Sorry.
1) You could put it in one of the loops (after your drive pedals) and just activate it when needed. 2) Or you could place it in-line from the output. Or 3) If it's only one pedal causing noise, put it in the same loop as that pedal. Hope that helps.
Yes you can do that. Set the Et function to both 1A and 1C but different values. E.g. Set Et on 1A to on and Et on 1C to off. Exact settings will vary depending on your amp. HTH.
Hello from Christchurch New Zealand! Do you know if the PXL Pro can be used to switch the Boss Katana 100w Head. I know its a different amp but can't find any info anywhere...
Hi Mat (my sister and family live in Christchurch so greetings!). Yes the Joyo will be able to control the Katana just fine. The latching should work but if it doesn't then you can use the midi function, as the Katana has midi in. Hope this helps. Cheers
@@tonybarber420 the Katana has 4 selectable channels. The PXL Pro triggers can only switch between 2 channels. ie the switch is either on or off. There is no way to make the Katana go from patch 1 to patch 3 for example. Not sure if I'm explaining myself well...
That doesnt seem right.why wouldnt your channel 'A' be your bypass sound eliminating the need for 2 triggers...
Hello there!
I just got a Fender Bassbreaker 30 and it comes with a 2 button footswitch. The amp has 2 channels and a high gain button to drive the dirty channel even more.
On the foot switch, button 1 changes from clean to dirty and button 2 enables the high gain for the dirty channel.
When I connect my insert cable into triggers 1 & 2, the amp seems to only switch between clean and high gain, not allowing me to access the dirty channel on the amp without the high gain engaged.
Any idea what combination of trigger configuration/different cable routing options might work in this case?
Much thanks!
I wouldn't know unfortunately. Sorry. I'd reach out to Fender, see if they can help.
Is it possible to use the trigger fuction to change the clean and the distortion channel on a mesa dual rectifier?
Probably. I'm not able to check, though, unfortunately.
Hello, I've just bought a PXL PRO in order to control the channels in the Joyo Mjolnir but it doesn't work. The amp doesn't recognize the controller. I noticed that the cable which came with the amp is in stereo and the PXL PRO triggers are in mono. So I decided to get a stereo cable with one stereo connector and two mono connectors and it controls the distortion channel but not the clean. Can you help me please to solve this problem.
could you solve it?
@@leonemesis87 yeah! finally
Getting noise from loops that are deselected, ie my drum pedal can be heard at a lower volume even though I'm bypassing that loop. Wtf.
Might be a cable shielding issue. There's no quick fix, other than to check all you connecting and power cables unfortunately.
@@thehont8648 thanks for reply will get to the trial and error thing... Cleaner power and better cables to start. Thanks
Interesting setup. Will check the Joyo switcher. What cable model did you used to interconnect the pedal? thanks
Hi would the triggers work with an vox ac15ch ? To switch between the normal and top boost channel. ( A 1/4" from 1 trigger to normal channel and 2nd trigger to top boost channel) ?
What I'm looking to do is for eg. Have distortion pedal on in normal channel , and then with the press of a button switch to top Boost channel with distortion pedal off.
Thanks Mark
In theory that should work fine, as long as your amp has a foot switch input (which most modern AC15s do). You would then connect the JOYO to the foot switch input. I'd check with VOX to be absolutely sure it will work though.
Hey.i am using a dsl 100.only one channel switch possible. I plugged in in trigger 2 and i see there is the green light at the amp but it jumps back to red quickly.so i cant use the the overdrive channel. Is it possible that i have to use a stereo cable instead of a mono cable? The footswitcher has a stereo cable?
No idea. Sorry. One for Marshall themselves I think.
Thanks for the video! I'm new to this sort of stuff - is this using Control Voltage to change the channels? I ask because I have an Empress Echosystem that can receive control voltage of 0-5 volts to change knob settings, wondering if this would work for it?
No idea. Sorry. One for JOYO themselves I suspect.
Quick question what if I’m using a three channel amp that also has reverb will two triggers be enough or would I need more trigger outputs?
Depends on how the channel switching works. If it cycles through the three channels two would be enough. If each requires a separate trigger then it won't.
@@thehont8648 Thank you!
thanks for sharing the vid. i'm pretty stoked on the PXL looper, and curious what pedalboard you have it paired with here. wanted to pair it with the Accel XTA21 but the swithcer tray is a little too narrow (20" vs 22" Joyo PXL). thanks again
Sorry. Only just seen this now. The pedalboard was self-built, though, so it probably doesn't help.
Is it possible to trigger two different amps like amp A and amp B?
In theory, yes, but I've not tried it so you might be best to check with JOYO support.
Hi I have a question, is that trigger for momentary or latching switch? I just need a signal at a moment for my bugera 6262 it will works?
You can set it to either. See from about 3:10 onwards. Hope this helps.
thx
I got a Peavey triple X head and I bought a custom made cable that splits the seven-pin footboard pedal output into three 1/4” jacks to plug into three of the trigger inputs of the Joyo Pxl Pro’s four trigger inputs. I’m having difficulty programming channel 1A to be set to the ultra channel on the Peavey Head and channel 1C to switch to the clean channel. It seems that when I correctly set it up for channel 1A, having the polarity on only for trigger 1, then program channel 1C, having the polarity on only for trigger 2, it wipes out my polarity saved setting for channel 1A setting it so only trigger 2 polarity is on preventing me from activating the distortion channel when I switch back to 1A.
Hi there. That's not something I can help with unfortunately. I doubt that either the Peavey or the JOYO have been designed with this configuration in mind. Sorry.
@@thehont8648 Its cool man. After some playing about, I figured it out. If anyone asks you again, let me know, I can tell them how!
@@Brjostabarn Cool. Glad you worked it out.
how would you connect a noise gate ns-2 with it?
1) You could put it in one of the loops (after your drive pedals) and just activate it when needed. 2) Or you could place it in-line from the output. Or 3) If it's only one pedal causing noise, put it in the same loop as that pedal.
Hope that helps.
I am trying to get 1A on dirty channel then when I step on 1C have it switch to clean channel.
Yes you can do that. Set the Et function to both 1A and 1C but different values. E.g. Set Et on 1A to on and Et on 1C to off. Exact settings will vary depending on your amp. HTH.
Ok thanks will try it.
That did it. Thanks!
:-)
Hello from Christchurch New Zealand! Do you know if the PXL Pro can be used to switch the Boss Katana 100w Head. I know its a different amp but can't find any info anywhere...
Hi Mat (my sister and family live in Christchurch so greetings!). Yes the Joyo will be able to control the Katana just fine. The latching should work but if it doesn't then you can use the midi function, as the Katana has midi in. Hope this helps. Cheers
Hi! Were you able to figure that out? I desperately need help with the Boss Katana trigger inputs.
@@sophiaplotkin6710 Nope. I ended up buying the GA-FC foot switch. The triggers on the PXL Pro 9nly switch between 2 states. The Katana 100 needs 4.
@@halfwayquiet what do u mean "needs 4" how did it not work? Im sure you didnt do something right
@@tonybarber420 the Katana has 4 selectable channels. The PXL Pro triggers can only switch between 2 channels. ie the switch is either on or off. There is no way to make the Katana go from patch 1 to patch 3 for example. Not sure if I'm explaining myself well...