Fix Skateboard Razor Tail, Chips, and Delamination
ฝัง
- เผยแพร่เมื่อ 22 มิ.ย. 2024
- Learn how to Fix Razor Tail, and large chips in your street deck or longboard deck.
Go to ratvision.com/ for more info.
For great prices on Longboard and Skateboard equipment we recommend
stokedskateboards.com/
When the tail of a skateboard deck gets warn down it becomes known as a "razor tail". This describes how thin or "sharp" the wood becomes. A razor tail can lead to chipping and it reduces "pop" from the deck becoming less stiff or rigid. By applying wood glue and reshaping the tail with sandpaper a deck can last a lot longer and get some pop back to make tricks higher.
Sometimes a skateboard might get away from you and slam directly into a wall, ledge, or a curb, causing the veneers or plies of wood to separate and/or chip. In skateboarding, this is known as delamination, or delam for short.
Delamination can also be caused by leaving a deck outside for too long. What happens is moisture gets into the deck causing it to expand and separate the veneers from each other. A skateboard deck can also come apart from being left in a hot car.
In these cases the damage can be quite extreme and it may be better to replace the deck than try to repair it.
VERY RARELY does a skateboard deck delaminate on its own. Nearly all manufactures warranty against delamination within a defined time period. If this actually happened to you the skateboard shop you purchased the deck from or the manufacturer may exchange the deck for a new one if they can determine that it was not caused by negligence.
HOW TO REPAIR DELAMINATION AND RAZOR TAIL:
Note: This works for longboards too.
1. Determine how many plies have come apart, and how wide the effected area is.
2. Spread the plies apart starting with the lower plies first.
3. Add a quality wood glue by squeezing it between the deck plies.
4. Holding the deck vertical you can use gravity to help get the glue deeper between the plies.
5. Wipe away any excess glue that is running or dripping.
6. While using a clamping call, add clamps and tighten them securely to the deck. This will sandwich the plies back together and squeeze out any extra glue.
7. Wipe away glue that is dripping or running again.
8. Remove clamps after waiting 24 hours for wood to dry.
9. After removing clamps, begin sanding away hardened glue and reshape the end of the deck. When reshaping the deck it is OK to sand away part of the deck itself. Sand until you feel comfortable with how thick the end of the deck is.
There are many glues available that will work well for repairing a chipped or delaminated skateboard deck. Be sure the glue you choose works specifically for wood. Follow all instructions labeled on the glue package.
For any questions about this video or if you need additional help fixing razor tail send us a message or comment. - แนวปฏิบัติและการใช้ชีวิต
Quick tip: Use gravity to your advantage, while gluing, work with the board in a vertical position so that way the glue can down the further gaps of wood inside the board.
Sore loser who spends huge amounts of his time posting comments on TH-cam. Your name is great
Thanks
Sore loser who spends huge amounts of his time posting comments on TH-cam. Your name is great
Sore loser who spends huge amounts of his time posting comments on TH-cam. Your name is great
awesome DIY, i wish i had this 10 years ago when my parents would make me skate the same deck for a year
A year? Thats nothing compared to most kids
I skated the same deck until it broke. :-D
@@DetenkleFriluftsliv Same that's what most people did, when I was a kid I used to use the superglue with saw dust on my tail if it was really bad.
"my parents made me skate the same deck for a year" that's so beta, dude. If you wanted another deck maybe you should got a job. 😜
I'm still riding the same deck since '94. Sure, it's wrapped in duck tape with PVC pipe splints, held together with a gallon and half of wood glue, fiberglass patches, band-aids, and rock hard bubble gum, plus one Boy Scout pine wood derby car wheel, but I can still tre-flip for days with it. Come to think of I'm not even sure there is any wood left. I'll post a picture.
wow this actually helped my razer tail i thought sanding the tail would make it so much shorter but i guess not thank you!
I highly doubt any skate shop will do anything but laugh if you try to return a skateboard that's been 'damaged' from skateboarding even a couple of minutes, let alone a month.
+Arno Theadorno Well, I bought a board three days ago, the company is Good Wood and they are suppose to have boards that really resist delamination due to gluing the board together by cold press instead of hot press like most other brands do. After three days and only dropping the board 4 times on the nose, it is starting to delaminate and its just a waste of money at this point, Im sure its just a defect. But I did contact the company to see if we can arrange. Yeah if you are slamming your board hard against the floor and and kickfliping a 5 stair they wont accept a return or change XD.
that's not true I know a lot of people that had that happen to my cousin got a board and only had it for like a week and he did a Ollie and it snapped and they replaced it
+Jack Hildebrand omg I hope you learned your lesson goodwood is known to all the skaters Ive ever spoke to LITIRALLY everyone, that its the worst possible board you could buy at a shop
Arno Theadorno Vans exchanged mine after 1 month of use
@@exzaviorw I CALL BULLSHIT
i thaught you said "about a fuck a piece" when you were talking about the c-clamps
Same
lol
+tavros nitram same
+tavros nitram lol, me too. i kept on playing over and over again lol.
Me too! Haha
at 2:21 when he said "about a buck apiece" I heard about a fuck apiece and was very concerned for a moment
That's because you have a young mind.
Rat Vision - Skateboard Tech no just shitty headphones.
I heard the same thing o.o
Dude same hahaha
" two clamps (these are one-inch c-clamps, about a fuck a piece "
*TIP:* If you have trouble getting the glue between the plies or want to do a more thorough job, before you start putting glue on, get a cup and mix some glue and water together until it's as fluid as water but still white from the glue. Get a brush, sponge, (or your finger) and apply it to delaminating edge. You'll notice the wood will suck in the glue/water because of how fluid it is. If it doesn't, you've put too much glue in the mix. Apply this mixture twice to let the glue/water really get absorbed into the wood, then get your normal glue and continue as stated in the video for the more obvious splits.
Also helps keeping it vertical so bubbles will rise up.
This might help here. When repairing guitars I use a large syringe with a large bore needle that is filled with wood glue. Doing this allows you to get the glue to get deep into the crack and allow a much stronger and permanent fix.
I can see you know what your talking about. To many "TH-cam PROFESSORS"
It's common sense but people just dont have much lol🤘🤘👍
As a guitarist I can confirm this works. I had an unfinished guitar and the top started to pop off.
Thank you so much! Just bought a deck 2 weeks ago and everytime I choke a tre flip the side of my deck kept on hitting the floor so by two weeks I already had a chip on right corner of my deck so I watched ur video bought the glue clamps sand paper and the wood filler and my deck is as good as new :)
Great!
We are going to make more videos. We are currently working on other things. If you have any questions, you can leave a comment or send us a message. We will get back to you asap.
You can send us pictures to info@ratvisionDOTcom. It's better to try and fix the deck before buying a new one. Make sure the pictures are good angles and in focus.
We've been working hard finishing a new website, once that's going we'll be making a lot of videos. Sorry for the huge delay.
"Razor tail" is when a tail gets warn down so much it gets a thin and sharp edge.
See other video in our channel.
Send us a private message through our channel about what type of skating you want to do and we can do our best to help you find a setup right for you.
Did anyone else hear "about a fuck a piece"????
It's "buck". Young people hear what they want to hear.
Sounded like a "fuck a piece" to me too and I'm 44....lol
ahahah
+howlingmaddmurdock says the man who started the channel: "Adult world sucks!" :-) :-) :-)
+John Toth I'm all over TH-cam Lmao! And apparently you are too John. This is a pretty cool informative channel.
you saved me so much money thanks
I don't even have any problems with my skateboard. I can't stop watching cause YOU SEEM SO NICE.
Thank you for the comment. We've been really busy with the new site launch. We'll be posting a ton of video once we get things settled. Should be soon.
i dont know how you manage to put up with all the dumb questions, my personal favourite was "can you paint your wheels" hahahaha
Euan Chester I did. Worked great. Why is that dumb? I but wheels that were white with pink graphics can I paint it over with grey. Looks great.
2:20 he said a f*ck of piece
Press the timestamp again and again youll understand what im sayi'n
lol your right
lol i was about to comment that when i saw your comment
Please make more videos, your videos are the most reliable when it comes to talk about skateboards and longboards maintence and fixing. I`m totally subscribed and waiting for more videos!
You're awesome Seth. Such a fan. As you may know we are finishing a project, and we'll have new videos up asap, because the new project requires them.
I was wondering if there is a way to clean skateboard/longboard wheels?
With a wet towel and soap. Just don't get the bearings wet.
powerslides
They're meant to be dirty?
2:20 "about a fuck a piece" 😂
Is everyone in the comment section deaf?
No idea how you're hearing "fuck". It sounds like buck with and without headphones.
What trucks do you have? Is the hanger pivot smooth? Are your trucks really loose or really tight?
Follow the steps on using sandpaper in the video.
I think its funny that he says 1/8 is hardly anything but when you ask someone about the size of their board every mm counts :P
When I go from a 8.3 to an 8.4, I notice.
ya but its mostly the width that matters and that's how they measure boards 7.75 8.0 8.125 etc
Ya ok...but popping an ollie is a hell of a lot easier with a right sized tail.
In order to avoid that type of problems, you just need to buy a new deck😂 lol
if your father gives you money, like yours:D
+Nikita Panfilov i buy blanks so it's completely worth just getting a new one. but if someone who swears by a specific brand, yeah. this would be a great project.
+sneak. Well, if you have a JOB, work 4 hours in one day, you can afford a new board almost anytime, especially for a teen who does no really have anything to spend that money on (taxes, bills, etc...).
I'll answer my own question - it definitely does! Noticeable difference after I sanded the razortail back with a belt sander, and huge difference when I replaced the griptape too! Awesome tips, hopefully will get another month out of this deck :)
Thank you. Glad you like it, and it helped.
"Use something flat and hard" heh heh, giggity
so immature
+X3GamerchicX3 so mature.
IlbanGRomero are dicks flat now?
@@SJS325 yes if they got flat after getting crushed by the toilet seat
@@Local_commentor a little late bud
how bout a new deck,
you want to give me 90 bucks sure
+Lochlan Hughes struk sells them for 35 and they are very good
In australia there is no such as thing as cheap deck unfortunately most start at 60AUD and go up
Lochlan Hughes i know aye
How bout I have no fucking money and can't buy a new deck every month
Glad this worked out for you. Totally works!
I REALLY HOPE SO. Your videos help me a lot. You're really good at explaining what and how to do things. Please keep them coming.
u r a gaylord
Says the guy who likes baker
+nivlac says the guy who loves sector 9 (a shot china company)
Raffi Jerahian you're a gay god
Raffi Jerahian are you a twelve year old
Baker's the shit though.
Absolutely. If the tail gets too thin it can flex as you put pressure on it when it touches the ground. This reduces the "pop" because the tail is not rigid enough to rebound/pop off the ground to create the lift you want.
Thank you. Yeah we haven't posted in a long time. The purpose of this channel is to educate people, and give them the facts about products, brands, and how things work. We try to reply to comments every day. Just because we don't have videos doesn't mean we can't still help and educate. We got to keep the stoke going for sure.
We will have more in the near future. We've been working on other projects.
great! im so glad you guys are making videos more often!
We will have videos on bushings and trucks, and more on wheels.
We've been busy with another project. We are trying to set some time up to release more videos later this Summer.
Please can you make more videos this is the only channel thats clear and really easy to follow !
Send us a personal message through our TH-cam channel.
This tip is the best of all your videos! Thanks a lot!
What would you like to know? Anything specific?
you have the most helpful videos on youtube!
THIS VIDEO IS PERFECT!! THIS IS THE SECOND BEST TIP IN SKATEBOARDING!!
We actually have all those ideas on a list for videos. We have been very busy with our website. We will be posting a ton of videos once we get everything done with our site. Thanks for the tips and your nice comment.
Hey Awesome! Glad this video worked out for you.
AWESOME!
Nope, alive and well. We are hoping to post more video later this summer. We have been working on another project, so we put videos on hold for quite some time. We still answer comments and messages every day. If you have any questions we'll answer them.
This helped a lot, Me and my older brother did this to his board and the results were great! Thanks (:
i currently have no skateboard issues..i just like to watch your videos..i cant wait for more
thanks so much for these tips.I haven't needed to use them yet but I'll know they'll come in handy. :)
We will. This Summer we plan to release new videos. We have been really busy with a different project for skate shops.
These videos are gonna save me hundreds of dollars!
Woo hoo! What we need are subscribers. Please subscribe if you haven't already. Thanks
As I've said before, I really enjoi these videos. If you ever get around to making more, perhaps a tutorial on applying rails and skid plates to the deck would come in handy (I am currently unsure how to pick out skid plates for a freestyle deck). How about low trucks vs high trucks, freestyle wheels vs street wheels vs filmer wheels, or a fun video on what to do with decks you no longer use (turn them into cruisers, build furniture with them, etc.). This channel is great!
How old is the deck? Was it left outside over night, in a hot car for days, or been wet?
Wow this channel is really really helpful, like seriously helpful
Go to our channel it's already there. In fact, it's also in our video for fixing a chipped deck.
Good!!!
THANKS!!!
The next video we will post will be on bushings. Most of it has already been filmed. It won't be posted for a while though. It will be good and blow peoples minds.
Yes!
Local shops are the heart and soul of the industry. It's what drives the skate economy. These shops are what made skateboarding available to everyone before it became mainstream and before the advent of the internet. These are the shops that care about skating and they take care of you. Corporate stores like Zumiez and Tillies care about one thing...Money! Skateshops care about the community, skateparks, and your passion for skating.
Watch our video on how to fix razor tail.
Great video instruction! Nice tip with the grip tape paper. Was looking for info to partially restore a vintage deck.
Thanks!
WELCOME BACK!!!!
Appreciate that you reply to most comments
THANK YOU!
Love your vids PLEASE KEEP MAKING THEM!! I was wondering can you do toutorials on tricks???
Nice video series guys. Damn...,it has been a while since I've seen common sense like these. Keep it up!
your videos have helped me alot thanks man :)
Woo Woo! Thanks
Thank you sir for this good lesson and now I am subscribing this channel!!
I'm relatively new to skating so I REALLY take good care of my board. I did exactly what you did but with variations. I rinsed them in water, blow-dried each one thoroughly, cleaned it with the orange cleaner(I did each bearing separately because I didn't make that shaker bottle thing), lubed them with Bones Speed Cream, and they still go bad pretty fast.
Hey Skateboardtech, Great Vids! U just got a new subscriber!
we will be trying to release new videos this summer.
We will have more after we launch our new website. I'm dying to make more, so there will be more.
I love your videos =D you have taught me so much stuff
That's incredible.
Thank you for the nice comment.
Watch the video we did about the differences between bearings, such as ABEC ratings, Swiss and ceramic. There is also a good video we did about spacers.
I just did this with my 22 year old deck. Just got back into skating and I can't afford to get a new board just yet. Thanks for all the great tips!
Any questions you have until then?
That's amazing, with my last board I just used some wood glue and a clamp. I don't have a lot of sand paper around the house so I never really thought about it, but if the same thing happens to my board I have now then I try it out, Thanks a lot bud.
Thank you, i've been swapping decks monthly because i skate a lot of street and winter makes it even faster. Now i can save money.
Thanks we are about to in the near future. Been busy with other stuff.
Ha, we are getting to that. We are going to be posting charts/tables that feature test results for top brands on the Rat Vision site. Very similar to Consumer Reports magazine.
Loving the leftover hardware sticker!!!
What do you want to know? Of course we will do a video about durometer.
What's the first?
Post more videos this channel is awesome
Sorry for the late reply it showed up as Spam. Did you get the nut off?
I really like your videos and I think you should make them EVERYDAY :-)
thks dude! this video was very useful to me!