Mini Cooper Reset Service, Brake Pad Reset, Spark plug Reset, Oil Service Reset R60
ฝัง
- เผยแพร่เมื่อ 1 ต.ค. 2024
- Desription of service indicator and demonstrates how to reset your service indicator. Brake Pad Reset. Oil Service Reset. Spark Plug Reset. Vehicle Check Reset. State inspection Date Reset. Brake Fluid Indicator.
This year cooper is one of the best in terms on engine longevity. But it is common for the exhaust to rust out so take a good look at the exhaust and hangers. Also if it is a manual transmission it should be good but the automatics tend to fail at higher mileage ranges.
Is their a way I can program a new fob without having to go to the dealer?
Worked like a charm. Straightforward and easy to follow. 'THANKS' for the video!
+Joe M Hello Joe, Thanks for posting! Glad my video helped bud!
The R56 uses the cluster and the BC button but most are very similar.
The best and helpful video!
I reset all menu except front brakes :(
still can not reset them. How can I reset front brakes ?
Thank you!
Hello Vladimir, This is usually due to a failed sensor or the sensor is worn through. I also have seen aftermarket sensors not allow resets. I would hang a new sensor not installed. Just plug it into the connection for the body harness side and try to reset the light. If it goes out it proves the sensor is bad.
Hello, This is a code for the intake camshaft sensor. IMost of the time the failure is just the sensor. I will be trying to make a video on this sensor this weekend.
The sensor can cause the brake and ABS lights to come on but the only lights you see should be for the brakes. Replace the sensor and reset the reminder, hopefully it will remove the warnings you see.
Did you follow the reset procedure and was the sensor replaced?
Unfortunately you cannot go back once it was reset. The dealer may be able to using a test plan that can change the oil service counter and mileage. It might be worth just keeping track yourself or an extra oil service never hurts :)
Some resets are done by just leaving the key on but engine off. Others like the mini in this video needs to be reset as shown.
Not something I will be able to make unfortunately. Not until I own one :) Still have a long way to go on my E46 though.
Hi there, I'm assuming, yes / no, can I follow this procedure for a Cooper S 2013. I seem to be able to reset all the info, but the service light is still showing. What could I have missed ?
+A H Hello, When you start your vehicle it will always show the next service due even if it still has quite some time before it is due. Maybe this is what you are seeing? You can also contact me via my website at www.bmwdiy.com if you need further assistance.
+AskTheCarExperts Thanks, will go check again and revert back if I'm still stuck :)
Thank you thank you thank you!!! I have tried everything to get these messages to stop popping up after getting my new (to me) car was serviced and I couldn’t figure it out. You’re a hero.
Hello, That symbol is usually for low brakes. Your brakes may be worn past the brake pad sensor or the warning you see may be due to low brake fluid. If the fluid is good you should have your brakes inspected.
This sounds like the outside temp sensor and or wiring may be damaged. Then the wires or open in reads -40 when touching they can read +122.
THANKS
Your very welcome!
hey, can i do this but instead of erasing the warnings i need to make warnings back, so can i put like 01/2010 so the car would ask for service? thank you
I drive 2001 bme e39 530i and i have a problem the check engine light is on and the code is p0344 some thing with the camshaft position sensor did you k now what is that mind /????? Or what can cause the p0344 code ???
Thanks, super usefeul!
Glad it was helpful!
I replaced the brake pads off my mini cooper S and did not replace the wire that alerts when they need to be replace. After I was finished I noticed all the lights on the dash were blinking on and off. When I say all I mean all of those alerts pop up, but I'm guessing I would need to reset it in order to make those lights stop blinking...am I correct?
I have had my rear brake pad replaced today but the BRAKE light still on . How do I turn it off? Why do I need to reset the day of service when its set for time to be in for service? Thx
Only possible with the BMW tester at the dealer.
Hello Thomas, What does the indicator look like? Do you mean at 1:57 on my video it is the picture you see?
This may mean that the brake service is due. You should have your brakes inspected.
hey on my mini cooper 2008 between the mileage and the total mileage it keeps displaying -40.0c do u no why this is there even when the car is running????
I have had my rear brake pad replaced today but the BRAKE light still on . How do I turn it off? Thx
Men I did it . Thank you . Was very helpful
Thanks for the info.
Depending on the model and year a reset will be needed to turn the light off.
Can you make a video for changing the power steering pump and fan on a Mini Cooper? Thanks
I have a 2007 mini and the mini on the lift came on with the break light on the breaks are pretty much new so I'm not sure what it could be do you have any idea ?
my mini is 2010 base 2 doors. Did u turn your BRAKE light off ? If so , how please?
You are welcome :) Will do my best to try and get the VID for the sensor this weekend.
Very good..thanks
Hello Musa, Thank you for posting. I am glad my video was helpful. Please subscribe. Thank you!
Excellent explanation .... very clear and precise .... Thanks
Hi will this work for mini cooper s r56?
Thank you
:) Thanks Graziella, My wife things so too ;)
Thanks! very useful.
Depending on the year of the MINI a code needs to be entered for each new key. For newer MINI's you can do the key initialization procedure like I show on a BMW. The procedure is the same. This would only be for the remotes and not for starting.
thank u
Thank you!
The brake light still on?
Hello Abel, If the brake pad light will not reset it may be an issue with a brake pad sensor. They are one time use and if there is an open in the circuit it will not allow the brake pad reset to be performed. I hope this helps.
Thank you !!!! For your help
Thank you so much
Hello Michael, Your welcome! Thank you for watching and please subscribe. :)