The LTD Phoenix 1000 Evertune Review (OOF) :(

0:00 - Introduction and Gear Setup
0:22 - Active Mode
0:59 - Passive Mode
1:40 - Active vs Passive
3:20 - Lets Talk About The Evertune Bridge
5:48 - Drop Tuning with the Evertune
7:00 - Drop Tuning Playing
8:20 - Post Gig Report and Closing Thoughts
Much appreciation to Zzounds for lending me this gear to show you guys!
If you like my content, use the affiliate links below to purchase gear. 🤘
Phoenix
www.zzounds.com/a--3989488/it...
Brit-Tone Amps
www.brit-tone.com/
Splawn Amps
barrztrading.ecwid.com/Splawn...
Cables
D’Addario Cables
www.zzounds.com/a--3989488/it...
Ernie Ball Flat Ribbon Cables
www.zzounds.com/a--3989488/it...
Strings
D’Addario NYXL Strings
www.zzounds.com/a--3989488/it...
Camera Setup
Sony ZV-E10
www.amazon.com/Sony-Alpha-ZV-...
Sony 15mm Lens
www.amazon.com/Sony-15mm-APS-...
Godox Key Light
www.amazon.com/dp/B09N3P4YLH?...
Sony DSLR Microphone
www.amazon.com/dp/B0CBLDQLZ4
Rode Lav Mic
www.zzounds.com/a--3989488/it...
MD421
www.zzounds.com/a--3989488/it...
SM57
www.zzounds.com/a--3989488/it...

[@bearonguitar]

Hi. This is Herbert from EverTune here. I've been watching your channel since back when you started getting into exploring the Kemper Amp.
If you want the EverTune bridge to be active and at the same time allow for bending and vibrato, just as with any regular guitar, then you'll have to set it up accordingly. We suggest to specifically place the saddles inside zone 2, just at the edge of zone 2 towards zone 3, so that the EverTune saddles are active while you play and keep the strings balanced at all time, and so that any bend or vibrato will push the saddle over the edge into zone 3, where the EverTune feature is no longer active and the string will behave as with any regular fixed bridge, but will come back into zone 2 afterwards. This way you can play the EverTune equipped guitar like any traditional guitar and always know that it will remain in perfect tuning. You don't need to choose between stability or expression, with the EverTune you get to have both.
The way you position the saddles at the bendstop position this is you keep picking the string while tightening the tuning peg until the note starts increasing in pitch, then back the tuning peg off to where the note is back in tune again. This will have the EverTune feature active across all strings while allowing for most natural vibrato and bending.
I'm assuming you are new to the system. Let me know if you have any questions about the system including the setup, and I'll be happy to answer them.

[@FastRedPonyCar]

Thanks for the info. Yeah I kind of assumed there was a specific spot you could do that but to be totally honest, the rest of the guitar really just soured the whole experience. The evertune was the least of my problems with this instrument.

[@paulbradshawguitar]

if it's any help with regards to the evertune bridge, you can effectively sort of setup the amount of tension required to bend strings, which is quite unique
while still getting the benefits of a stable tuning, (ie. setting it between zone 2/3 to taste)
when you first change strings there's going to be a bit of 'drift' as it were until the string settles,
for context we play in drop B , i usually swap the strings maybe a week or so before with at least 1-2 band practices in, i don't have time to tune between our songs live, so the evertune bridge is a huge help, not to mention the improved intonation
otherwise tried the fishmans in an rgd/evertune setup, the voicing was also not for me , very tight/rolled off bass and almost like you've got a TS constantly engaged

[@michaelnugent9758]

Yeah and not in a good way. They have a weird frequency going on in the mids/highs that I just couldn't seem to dial out. Even with the HF Tilt wired. I REALLY wanted to like them.