Отличное видео для владельцев кросман. Это обязательная процедура. С металлической ствольной коробкой и апом системы накачки этот пекаль становится винтовкой.
if you look in the breech hole and notice where the pellet stops when the bolt is closed. it has the skirt mid way over the air hole and when you pull the trigger for a split second your pellet is pushed back and forward. the probe puts the pellet in front of the hole so that it only goes forward maximizing your air pressure...the o rings help as the air is only going to the breach and none escapes except down the barrel.
Здравствуйте, я сделал иглу в своем 1377, так же, как и вы, она была намного мощнее. Я также использую силиконовую смазку на поршне. Стало легче наполнять воздухом. объятия из Бразилии. (переведено гугл переводчиком)
Спасибо за видео туториал, действительно такой апгрейд делается за 10 минут максимум. Сверлил отверстие под досылающий шток сверлом 0.8мм, хвостовик этого же сверла и засадил на жидкие гвозди внутрь. Прогрел затвор термофеном, все стало как влитое! Теперь после 5ти качков тяжелая шпуля уходит в дерево полностью.
Я уже раз отвечал на двух языках. Но мне не лень повториться. 1 - улучшение герметизации болта, да и воздушной муфты (железное колечко, лучше его приклеить к стволу, а не как в видео), 2 - проталкивание пульки, теперь она не над отверстием, из которого воздух идёт, а дальше. Это всё увеличивает мощность.
i did all these mods to mine and my 1377 sounds more powerful...instead of air excaping it is forced up the barrel i also messed with the trigger spring to lighten the trigger pull the stuff this man is showing you really works great!!!
Мужики все работает! Проверено на кросман 1377. Я дополнительно приклеил металическую муфты на епоксид и прижал ствол металическим зажимом чтобы не тратил! Теперь пула H&n brakujące Hunter 0,67 g летит 190м/с можете пошитать сколько joules 😀. Я дополнительно смазиваю свинец маслом Power pellet lubе фирмы Napier😉 Спасибо за замечательный ролик и поздравляю из Польши
Thanks for the informative clip!I have applied your techniques where I can,as I have an early model 1377.The standard breach bolt does clear the pellet at least 4 to 5mm past inlet valve hole,but I did buy&fit an over sized o ring to breach bolt,and it is sealing really well now :) I just have to place an o ring on inlet valve,and job is done.Thanks again!
Спасибо. Я провёл ещё одну модификацию, но не заснял. Я взял ту маленькую муфточку, что положил в баночку, и намертво приклеил её эпоксидкой к стволу, так, что теперь утечки вообще ушли, мощность ещё повысилась. Но вот разобрать пистолет теперь до конца не получится, придётся оторвать муфточку, но меня это не особо волнует.
nice really nice job man extra seal to sealed any gaps pull the pellet 4mm foward so that way the valve hole has more space to realease the air nice idea dude
I have a 2240 and I have been thinking about grinding the bolt nipple to give more air flow and as a note, this mod pushed the pellet to the rifling and in front of the air port. This will increase your FPS about 20, but if you thin the nipple some you will get even more pressure. maybe 40 FPS. Trigger spring, take the back cap off and take the spring out and go to hardware store and find a spring same diameter that is 1/8 inch longer, the spring will be stiffer. The power will increase also. I added a 18" barrel with the mods and get about 600 FPS now...
bkr360 pushing the pellet further down the barrel does nothing because it's the bolt that partially blocks the transfer port ! Now by making the bold smaller on the end I could see that making a difference !
Robert Bush actually pushing the pellet further in (making it seat better) could help with accuracy. Why some people perfer single loading instead of using a mag. Well this could take that a step futher. It would sure or SHOULD surely seat all the pellets in the same exact spot in the barrel. At least i believe so... Join the topic. Always like better info, ideas, etc...
Да я хотел раньше купить МР512 в дереве, там всё как надо сделано, и качество неплохое, прицельные приспособы хорошие довольно, но она такая здоровенная, машины у меня тогда не было и я решил купить кросман, он в сумку помещается, ещё в добавок мощнее мурки.
Wow they really changed the design. My 1377 I bought in 1979 has all of that from the factory. plus a separate cocking handle on the rear. Pellets 745fps. BBs 889fps. They must make the new ones really weak now days. Be sure to use real pellet gun oil Not regular gun oil. Regular gun oil will damage the plunger/pump seal.
Я живу во Владивостоке, у нас почти в каждом магазине оружейном есть, ещё я один раз видел в магазине спортинвентаря. Я свой купил за 4600, в сети магазинов "Снайпер" он чуть дороже, в общем почти везде, где продаётся пневматика.
Мне повезло взять у друга довоенный американский набор шестигранников, и самый маленький действительно на 1 мм, я в магазинах такого не находил, но есть выход, можно напильником подточить 1.5 мм шестигранник до 1 мм, я где то читал, что кто то даже гвоздик так смог заточить.
Ну изначально носик "досылателя" короткий и пульку ставил прямо на отверстие откуда выходит сжатый воздух, удлинив носик я освободил путь сжатому воздуху, это первое. Ещё то колечко, что на "досылателе" стоит в самом начале, не достаточно плотно блокирует ствол с козённой части, ток что не лишним было его улучшить, таким образом избавились от основной утечки воздуха. Ещё я там резинку одел на стальную муфточку маленькую, которая соединяет накопитель воздуха и ствол...
@mlb0226 В начале использовалась не отвёртка, а шестигранник, вообще он довольно редкий, это самый маленький который бывает, кажется. Вообще его можно выточить из гвоздика.
Да, шестигранник редкий размер у него где то миллиметровый, тот что на видео - дал мне друг, это довоенный американский набор. Я где то читал, что люди их вытачивают из уже готовых шестигранников или гвоздиков. Возможно есть смысл после вывинчивания пропилить винт под минус.
If im not mistaken there are 3 seals one to close the opening when a pellet is inserted, one in the form of a ball which is released when the weapon in discharged and the obvious one used to pump pressure into the gun. Did you consider putting a better spring behind the bolt so it stays snugly in-place when ready to fire and replacing the seal as you did? Could you explain why exactly you added length to the feed probe? Thanks.
having torn down my 2240 last night, I was thinking this exact mod, the air from the valve hits the front and back of the pellet, so this is the perfect mod... the extra seal makes more pressure in the barrel.
Возможно ссылка была перемещена, я тоже не смог открыть, попробуй поискать вручную. Это не ап, а скорее доводка, которая убирает основные утечки воздуха, ну и носик на досылателе удлиняется, что бы пулька не вставала прямо на отверстии, откуда подаётся воздух.
hi i have a American classic Crosman 1377 .177 cal its an old one i think it was made in the 80's or 90's it will not pump up,,, What website did you get your parts from ? thanks for the video
having torn down my 2240 last night, I was thinking this exact mod, the air from the valve hits the front and back of the pellet, so this is the perfect mod...
Спасибо, Лёха, отличное видео, всё понятно, будем делать. У меня только шестигранник на 1,5 мм не встает на тот маленький винтик, что в бриче. Неужели там 1 мм?
@aqtemka у меня нет хрона, я не знаю какая теперь скорость, но выстрел стал звучать как бы сочнее и пробивать пистоль стал то что не пробивал, например пластиковую бутылку с водой с 6 метров насквозь, ещё заряжать стало удобней.
I keep an older model 1377 [has a magnet on the end of the bolt to hold one steel BB] In my car. I carry it as defense as it will easily break a car window, punch a hole in sheet metal and if needed puncture an assailant - with no firearm restrictions, Again LOKYleha, great video, great engineering and gunsmithing skills.
Леха! Супер видео, но остались вопросы. 1. На сколько мм в итоге увеличился досылатель? 2. На досылатель добавил второе резиновое колечко из зажигалки?
Спасибо, давненько я его сделал) Увеличился на миллиметров 6, да, резинка из зажигалки, но со временем я чёто в ней смысла не увидел, гнездо под удлинитель досылателя миллиметров 8.
In addition to brown parts, plastic is black sighting equipment and black box of bolt (my natural language is Russian, I can not translate special tecnical words correctly). Brown plastic nice and solid. Black plastic sighting equipment is not very good. Black plastic box of bolt is good.
A file works best when you go in one direction. Plus it will take more off a lot faster than going back and forth. Depending on the files direction will depend on which way you go in.
use silicon oil , other oils can explode under pressure its known as 'dieseling', also good for more fps ! put a drop of light oil in the back of a pellet ,goes with a bang ;-)
хороший обзор , спасибо, вот только замучился винтик долбаный выкручивать, объездил весь район , кроме китайского говна-набора миниотверток ничего не нашел, точил шестигранник , бесполезно , только бошку сорвал, наточил советскую тонкую отвёртку , плоскую , и накернул болт , все пошло, потом просто расточил ножовкой паз под плоскую отвертку, остальное труда не составило , вроде мощнее стал стрелять
Ох уж этот долбаный винтик, я еле шестигранник тогда нашёл, советую его пропилить под шлицевую отвёртку. Я там ещё одну модернизацию провёл, я намертво приклеил тот мелкий железный цилиндрик к стволу эпоксидкой, мощность ещё возросла.
Я где то в комментариях написал ещё про одну небольшую доработку, можешь поискать, там про то, что я железную воздушную муфту приклеил к стволу намертво эпоксидкой, стало ещё лучше, утечек вообще, как будто нету.
Эх хоть бы кто отстрелял бы на скорость пули до и после процедуры , понятно что улучшение будет , но вот на сколько ? Есть 1322 не прошедший данную процедуру но нет хрона , есть идеи у кого ,как сравнить без хрона корректно ? Кроме выстрела в доску с одинакового расстояния до и после что то в голову ничего не приходит
... там изначально просто металл воткнут в металл, безо всяких прокладок. Вот то что я сделал на видео это херня, сейчас я взял эту муфточку и эпоксидкой приклеил к стволу, утечки вообще практически исчезли, пистолет стал заметно мощнее, правда теперь не так просто его разобрать из-за этого стало, да и пофиг, надо будет разобрать оторву муфточку от ствола.
@dragonforcerockshard The bb's are sub-caliber. That's why they roll out of the end of the barrel. They are actually size B steel shot not BB. If you bought real BB size steel shot from a reloading supplier they would spoil your rifling and might stick in the barrel. The bb's sold for air guns is .170 caliber not .180 like reloading BB.
Требуется усилие для того, что бы пульку пропихнуть, или для того, что бы резинку прижать? Если именно пропихивание пульки смущает, то скажу, что диаметр пульки слегка больше диаметра ствола, что даёт хорошее прилегание пульки к каналу ствола, это повышает мощность, раньше это усилие делал сжатый воздух и терялась энергия. Если без пульки тяжело закрыть, то советую поэксперементировать с разными резинками, может найдёшь удобную.
i like this alot, but i hate crosman they give you a decent pistol for cheap but if you want a scope/RD they force you to pay them again for that crappy barel mount (i need a mount to mount a mount for a scope? wtf is wrong whit them) or to buy a steel breech whit a scope rail (here you loose your "iron sights") whi dont they just make a version whit a steel breech, scope rail and mechanical sights? i would pay the litle extra for it
Okay thanks any ways I improved that seal on mine but I noticed that only the seal between the valve and barrel was missing an o-ring there is a big o-ring already integrated into the pumping arm and I noticed a significant improvement in stopping power with this thanks great simple free mod huge help I hope mores to come like compressing the trigger spring I can describe that to you in a pm if you want me to so you could make a tutorial it greatly improves the trigger pull much smoother
Не на инглише только одна аннотация, на сколько я знаю, потому, что мне её лень перевести, если хочешь, то переведи, я вставлю под русским текстом. Okey?
Are there oser plastic parts exept brown parts ? cuz i have bad memories about plastic, and is this plastic solid and correctly assembled ? And you re a fucking cunning handyman ;)
Honestly, I don't understand what the heck this guy is trying to do with this modificaton, The only part that has sense to me is the double o-ring for better sealing. If he think by pushing the pellet more deep into the barrel is goning to gain some extra velocity, he is totally wrong !. For achieving that, you have to increase the size of the chamber that is inside the metalic cylindrical body this model has under its barrel. A bigger compressed air chamber means more pumps to fill it at top and more compressed air, means more velocity and more cynetic energy for the pellet and both of these factors increase dramatically the final velocity of the pellet. This is the way to go for more velocity, but not what this guy has made here. Cheers, John from Chile.
Im pretty sure you made it far worse than before tbh... You can replace the cylinder with an American version. They have no bleed holes. If you can invest into a brass cylinder. They are capable of 570fps.
Отличное видео для владельцев кросман. Это обязательная процедура. С металлической ствольной коробкой и апом системы накачки этот пекаль становится винтовкой.
if you look in the breech hole and notice where the pellet stops when the bolt is closed. it has the skirt mid way over the air hole and when you pull the trigger for a split second your pellet is pushed back and forward. the probe puts the pellet in front of the hole so that it only goes forward maximizing your air pressure...the o rings help as the air is only going to the breach and none escapes except down the barrel.
Здравствуйте, я сделал иглу в своем 1377, так же, как и вы, она была намного мощнее. Я также использую силиконовую смазку на поршне. Стало легче наполнять воздухом. объятия из Бразилии. (переведено гугл переводчиком)
Спасибо за видео туториал, действительно такой апгрейд делается за 10 минут максимум. Сверлил отверстие под досылающий шток сверлом 0.8мм, хвостовик этого же сверла и засадил на жидкие гвозди внутрь. Прогрел затвор термофеном, все стало как влитое! Теперь после 5ти качков тяжелая шпуля уходит в дерево полностью.
Я уже раз отвечал на двух языках. Но мне не лень повториться. 1 - улучшение герметизации болта, да и воздушной муфты (железное колечко, лучше его приклеить к стволу, а не как в видео), 2 - проталкивание пульки, теперь она не над отверстием, из которого воздух идёт, а дальше. Это всё увеличивает мощность.
2 пункт это миф, проверено!
i did all these mods to mine and my 1377 sounds more powerful...instead of air excaping it is forced up the barrel i also messed with the trigger spring to lighten the trigger pull the stuff this man is showing you really works great!!!
Мужики все работает! Проверено на кросман 1377. Я дополнительно приклеил металическую муфты на епоксид и прижал ствол металическим зажимом чтобы не тратил! Теперь пула H&n brakujące Hunter 0,67 g летит 190м/с можете пошитать сколько joules 😀. Я дополнительно смазиваю свинец маслом Power pellet lubе фирмы Napier😉 Спасибо за замечательный ролик и поздравляю из Польши
Thanks for the informative clip!I have applied your techniques where I can,as I have an early model 1377.The standard breach bolt does clear the pellet at least 4 to 5mm past inlet valve hole,but I did buy&fit an over sized o ring to breach bolt,and it is sealing really well now :) I just have to place an o ring on inlet valve,and job is done.Thanks again!
Спасибо. Я провёл ещё одну модификацию, но не заснял. Я взял ту маленькую муфточку, что положил в баночку, и намертво приклеил её эпоксидкой к стволу, так, что теперь утечки вообще ушли, мощность ещё повысилась. Но вот разобрать пистолет теперь до конца не получится, придётся оторвать муфточку, но меня это не особо волнует.
Excelente tutorial, con las mejoras mostradas se evita perder el aire de la pistola, así todo se aprovecha.
Gracias
nice really nice job man
extra seal to sealed any gaps
pull the pellet 4mm foward
so that way the valve hole has more space to realease the air
nice idea dude
I have a 2240 and I have been thinking about grinding the bolt nipple to give more air flow and as a note, this mod pushed the pellet to the rifling and in front of the air port. This will increase your FPS about 20, but if you thin the nipple some you will get even more pressure. maybe 40 FPS. Trigger spring, take the back cap off and take the spring out and go to hardware store and find a spring same diameter that is 1/8 inch longer, the spring will be stiffer. The power will increase also. I added a 18" barrel with the mods and get about 600 FPS now...
Good modification, and not a bad result, thank you for sharing.
bkr360 pushing the pellet further down the barrel does nothing because it's the bolt that partially blocks the transfer port ! Now by making the bold smaller on the end I could see that making a difference !
Robert Bush actually pushing the pellet further in (making it seat better) could help with accuracy. Why some people perfer single loading instead of using a mag. Well this could take that a step futher. It would sure or SHOULD surely seat all the pellets in the same exact spot in the barrel. At least i believe so... Join the topic. Always like better info, ideas, etc...
My 1377 has no bolt action for loading pellet,where or how is the pellet put in the receiver ?
Да я хотел раньше купить МР512 в дереве, там всё как надо сделано, и качество неплохое, прицельные приспособы хорошие довольно, но она такая здоровенная, машины у меня тогда не было и я решил купить кросман, он в сумку помещается, ещё в добавок мощнее мурки.
Wow they really changed the design. My 1377 I bought in 1979 has all of that from the factory. plus a separate cocking handle on the rear. Pellets 745fps. BBs 889fps. They must make the new ones really weak now days. Be sure to use real pellet gun oil Not regular gun oil. Regular gun oil will damage the plunger/pump seal.
I bought mine in the early 80's. Separate cocking handle and no brass bolt. I love mine, I shoot pellets and darts.
That gun oil thing is good to know. I was going to use gun oil, now I'll be using pellet gun oil...Thank You
Mine is advertised at 800fps with pellets
Я живу во Владивостоке, у нас почти в каждом магазине оружейном есть, ещё я один раз видел в магазине спортинвентаря. Я свой купил за 4600, в сети магазинов "Снайпер" он чуть дороже, в общем почти везде, где продаётся пневматика.
Мне повезло взять у друга довоенный американский набор шестигранников, и самый маленький действительно на 1 мм, я в магазинах такого не находил, но есть выход, можно напильником подточить 1.5 мм шестигранник до 1 мм, я где то читал, что кто то даже гвоздик так смог заточить.
Ну изначально носик "досылателя" короткий и пульку ставил прямо на отверстие откуда выходит сжатый воздух, удлинив носик я освободил путь сжатому воздуху, это первое. Ещё то колечко, что на "досылателе" стоит в самом начале, не достаточно плотно блокирует ствол с козённой части, ток что не лишним было его улучшить, таким образом избавились от основной утечки воздуха. Ещё я там резинку одел на стальную муфточку маленькую, которая соединяет накопитель воздуха и ствол...
@mlb0226 В начале использовалась не отвёртка, а шестигранник, вообще он довольно редкий, это самый маленький который бывает, кажется. Вообще его можно выточить из гвоздика.
Да, шестигранник редкий размер у него где то миллиметровый, тот что на видео - дал мне друг, это довоенный американский набор. Я где то читал, что люди их вытачивают из уже готовых шестигранников или гвоздиков. Возможно есть смысл после вывинчивания пропилить винт под минус.
If im not mistaken there are 3 seals one to close the opening when a pellet is inserted, one in the form of a ball which is released when the weapon in discharged and the obvious one used to pump pressure into the gun. Did you consider putting a better spring behind the bolt so it stays snugly in-place when ready to fire and replacing the seal as you did? Could you explain why exactly you added length to the feed probe? Thanks.
3. На сколько мм внутрь досылателя сверлил под удлинитель?
какой диаметр сверла использовался?
having torn down my 2240 last night, I was thinking this exact mod, the air from the valve hits the front and back of the pellet, so this is the perfect mod...
the extra seal makes more pressure in the barrel.
Возможно ссылка была перемещена, я тоже не смог открыть, попробуй поискать вручную. Это не ап, а скорее доводка, которая убирает основные утечки воздуха, ну и носик на досылателе удлиняется, что бы пулька не вставала прямо на отверстии, откуда подаётся воздух.
Hi..
to increase the power of the Crosman 1377, which component is replaced?
hi i have a American classic Crosman 1377 .177 cal its an old one i think it was made in the 80's or 90's it will not pump up,,, What website did you get your parts from ? thanks for the video
reseal kits are available on ebay, around $15
Very good. Your video is very good . Thankyou.
Hey I understand that english is not your natural language but about how much speed or velocity do you gain by fixing that seal? Thanks
having torn down my 2240 last night, I was thinking this exact mod, the air from the valve hits the front and back of the pellet, so this is the perfect mod...
Спасибо, Лёха, отличное видео, всё понятно, будем делать. У меня только шестигранник на 1,5 мм не встает на тот маленький винтик, что в бриче. Неужели там 1 мм?
Какой размер отвертки вы использовали в начале вытащить первый винт?
@aqtemka у меня нет хрона, я не знаю какая теперь скорость, но выстрел стал звучать как бы сочнее и пробивать пистоль стал то что не пробивал, например пластиковую бутылку с водой с 6 метров насквозь, ещё заряжать стало удобней.
Вот я тоже думал, что когда его сниму или заменю или пропилю что нибудь в нем. Спасибо за ответ.
@dragonforcerockshard BBs consists of steel. Steel balls may erase the rifling in the barrel.
I keep an older model 1377 [has a magnet on the end of the bolt to hold one steel BB] In my car. I carry it as defense as it will easily break a car window, punch a hole in sheet metal and if needed puncture an assailant - with no firearm restrictions, Again LOKYleha, great video, great engineering and gunsmithing skills.
Excellent craftsmanship.
здорова, а я отвёртку звёздочку T5 использовал, без проблем открутилось, сперва тоже начал стачивать шестигранник, но получилось кривенько :)
Леха! Супер видео, но остались вопросы. 1. На сколько мм в итоге увеличился досылатель? 2. На досылатель добавил второе резиновое колечко из зажигалки?
Спасибо, давненько я его сделал) Увеличился на миллиметров 6, да, резинка из зажигалки, но со временем я чёто в ней смысла не увидел, гнездо под удлинитель досылателя миллиметров 8.
In addition to brown parts, plastic is black sighting equipment and black box of bolt (my natural language is Russian, I can not translate special tecnical words correctly). Brown plastic nice and solid. Black plastic sighting equipment is not very good. Black plastic box of bolt is good.
Привет вы патроны на охоту сами заряжаете ? Напишите пожалуйста мне на Ватсапп? 🙏
Даааа!грамотно однако,молодец!!!
A file works best when you go in one direction. Plus it will take more off a lot faster than going back and forth. Depending on the files direction will depend on which way you go in.
what kind of oil do you use on the internal parts, air chamber ?
I use engine oil.
use silicon oil , other oils can explode under pressure its known as 'dieseling', also good for more fps ! put a drop of light oil in the back of a pellet ,goes with a bang ;-)
А какой диаметр шестигранника? Уже 3 набора купил не один не подходит(((, в пору хоть самому вытачивать.............
@supertolstyi Эпоксидкой клеил, именно это эпоксинка с повышенной прочностью, вообще любая подойдёт, главное состав нормально размешать.
To make a better seal, the stock seal isnt good enough ?
Why do this. whats the finished effect?
I want to know what extra power can you get with this extra arrengement..and of course the price.
+Jorge Frigerio, this mod gives +5% to start velosity.
@LOKYleha
Hey thanks for responding but I don't understand how a magnet can erase the rifling. Do you mind explaining?
хороший обзор , спасибо, вот только замучился винтик долбаный выкручивать, объездил весь район , кроме китайского говна-набора миниотверток ничего не нашел, точил шестигранник , бесполезно , только бошку сорвал, наточил советскую тонкую отвёртку , плоскую , и накернул болт , все пошло, потом просто расточил ножовкой паз под плоскую отвертку, остальное труда не составило , вроде мощнее стал стрелять
Ох уж этот долбаный винтик, я еле шестигранник тогда нашёл, советую его пропилить под шлицевую отвёртку. Я там ещё одну модернизацию провёл, я намертво приклеил тот мелкий железный цилиндрик к стволу эпоксидкой, мощность ещё возросла.
Имеется ввиду резиновое колечко?
Я где то в комментариях написал ещё про одну небольшую доработку, можешь поискать, там про то, что я железную воздушную муфту приклеил к стволу намертво эпоксидкой, стало ещё лучше, утечек вообще, как будто нету.
Эх хоть бы кто отстрелял бы на скорость пули до и после процедуры , понятно что улучшение будет , но вот на сколько ? Есть 1322 не прошедший данную процедуру но нет хрона , есть идеи у кого ,как сравнить без хрона корректно ? Кроме выстрела в доску с одинакового расстояния до и после что то в голову ничего не приходит
@TheAirguner
My video shows how to fix some factory defects. Also it is based on one of the popular gun forum posts.
hi mate, good little mods there, for the transfer port tho you would be better putting a o-ring either side rather than just on one side ;)
... там изначально просто металл воткнут в металл, безо всяких прокладок. Вот то что я сделал на видео это херня, сейчас я взял эту муфточку и эпоксидкой приклеил к стволу, утечки вообще практически исчезли, пистолет стал заметно мощнее, правда теперь не так просто его разобрать из-за этого стало, да и пофиг, надо будет разобрать оторву муфточку от ствола.
I did the same. Very good and simple improvement. Nice and good video.
@dragonforcerockshard
The bb's are sub-caliber. That's why they roll out of the end of the barrel. They are actually size B steel shot not BB. If you bought real BB size steel shot from a reloading supplier they would spoil your rifling and might stick in the barrel. The bb's sold for air guns is .170 caliber not .180 like reloading BB.
и какая скорость пули теперь ?
The screw length stoped the plastic bbs from loading into the barrel
Что дает вообще данный обгрейд ?
Все сделал так же как автор видео, но почему то теперь требуется усилие при закрытие затвора. Если кто сталкивался подскажите в чем дело.
Требуется усилие для того, что бы пульку пропихнуть, или для того, что бы резинку прижать? Если именно пропихивание пульки смущает, то скажу, что диаметр пульки слегка больше диаметра ствола, что даёт хорошее прилегание пульки к каналу ствола, это повышает мощность, раньше это усилие делал сжатый воздух и терялась энергия. Если без пульки тяжело закрыть, то советую поэксперементировать с разными резинками, может найдёшь удобную.
Excellent work. Simply excellent
@LOKYleha
What do you mean by spoil the barrel?
i like this alot, but i hate crosman
they give you a decent pistol for cheap but if you want a scope/RD they force you to pay them again for that crappy barel mount (i need a mount to mount a mount for a scope? wtf is wrong whit them) or to buy a steel breech whit a scope rail (here you loose your "iron sights")
whi dont they just make a version whit a steel breech, scope rail and mechanical sights?
i would pay the litle extra for it
понятно-спаси6о!
@dragonforcerockshard BB can spoil the barrel, because it consist of iron.
What exactly did you accomplish?
Okay thanks any ways I improved that seal on mine but I noticed that only the seal between the valve and barrel was missing an o-ring there is a big o-ring already integrated into the pumping arm and I noticed a significant improvement in stopping power with this thanks great simple free mod huge help I hope mores to come like compressing the trigger spring I can describe that to you in a pm if you want me to so you could make a tutorial it greatly improves the trigger pull much smoother
0akie13 à
"Bad idea."
Odvrtat kus mosazi a místo toho přilepit epoxidem kus hřebíku? K čemu je to dobré? Už jsi měl vymačkanou tu mosaz, nebo proč jsi to udělal?
Udělal jsem to tak, aby na pelety růže není v jamce, kde je vzduch jde, a pak se ho.
@LOKYleha
what do u mean by spoil the gun?
Very good Idea :)
He didnt realize he put a pellet when he scale the pin to cut then he put another pellet, now it stock lol
Нет, та муфточка - это железное колечко которое у меня в руке на 01:02
This wont work for magazine guns, i tried that day, will need some , but not impossible
I'll remember, thanks
I have one like that how do i make mines more powerful?
@Darryl McCoy : there is already one o ring factory installed, he added a second on the other side.
In Russia I can buy bolt only for my AK-47, it is not suitable.
I totally agree with you
what does that do
Не на инглише только одна аннотация, на сколько я знаю, потому, что мне её лень перевести, если хочешь, то переведи, я вставлю под русским текстом. Okey?
Wat is that mod suppose todo
ИЖ щас уже совсем не тот. купил и хоть выбрасывай. следом купил крыса-это совсем другое дело!!
@TheAirguner not that that would defect rather imperfection.
ah i see why you did it now yea, you did it to push the pellet further forward and to create a better seal for accuracy and efficiency
i would love to take the credit but ol LOKYleha is the man! but yea this is a super easy kick ass mod!
crossman vantage
there is no stock seal on the barrel...
I don't think i'll bother
You meant the manufacturers couldn't make that adjustment? The ....
Are there oser plastic parts exept brown parts ? cuz i have bad memories about plastic, and is this plastic solid and correctly assembled ?
And you re a fucking cunning handyman ;)
Honestly, I don't understand what the heck this guy is trying to do with this modificaton, The only part that has sense to me is the double o-ring for better sealing.
If he think by pushing the pellet more deep into the barrel is goning to gain some extra velocity, he is totally wrong !. For achieving that, you have to increase the size of the chamber that is inside the metalic cylindrical body this model has under its barrel. A bigger compressed air chamber means more pumps to fill it at top and more compressed air, means more velocity and more cynetic energy for the pellet and both of these factors increase dramatically the final velocity of the pellet.
This is the way to go for more velocity, but not what this guy has made here.
Cheers, John from Chile.
@mlb0226 Если не ошибаюсь 1,25 мм
Im going to buy a rare earth magnet to put on the tip of the bolt so it can shoot bbs too.
Im pretty sure you made it far worse than before tbh... You can replace the cylinder with an American version. They have no bleed holes. If you can invest into a brass cylinder. They are capable of 570fps.
das usen da noodle dar.....good job
"box of bolt"=breech
THERE IS STOCK O RING ON THE OTHER SIDE
@Gixxer983 Yes