I have 2015 Corvette c7 gauges and trying to install it in 2017 GMC sierra, everything's work fine except RPM doesn't work at all, shows 0 RPM, even if rev engine up, is there anyway to fix that problem ?
What paddles were used in the camaro? I've been toying with the idea of doing a lt1 and 8 speed swap in a 98 c43 amg and want to have paddles. Haven't looked much into aftermarket paddles but your setup I'd exactly what I'd want.
Did you need to cut the floor for 8 speed room ?? I have LT / 8 speed from 2018 SS Camaro , Looking to put in 1955 Chevy truck will I need to cut floor I have 383 with TH400 NOW
Hello i have a 2020 tahoe z71 5.3L and i want to install the lt4 blower on my stock powertrain is it possible or there are any upgrades that i must do ? Thanks
Bad ass!!! Love the gauges, sure wish it was available, you guys are the most productive LT swap channel on TH-cam no doubt 👍🏾👍🏾
That is a really sweet 68 .. makes me really jealous and needing to get my 67 started. Well done 👍
Test drive went a bit rough. The power steering pump ate a belt. Fixing that and hoping to get some miles on it
You guys are no joke! Nice work
That Camaro is friggin nice!
I have 2015 Corvette c7 gauges and trying to install it in 2017 GMC sierra, everything's work fine except RPM doesn't work at all, shows 0 RPM, even if rev engine up, is there anyway to fix that problem ?
What paddles were used in the camaro? I've been toying with the idea of doing a lt1 and 8 speed swap in a 98 c43 amg and want to have paddles. Haven't looked much into aftermarket paddles but your setup I'd exactly what I'd want.
Firebird* my bad. I was skipping around in the video and didn't notice it wasn't a camaro
Did you need to cut the floor for 8 speed room ?? I have LT / 8 speed from 2018 SS Camaro , Looking to put in 1955 Chevy truck will I need to cut floor I have 383 with TH400 NOW
Anyway I can get In contact with him? I have some questions
What rear end ratio do you recommend with this same setup but on a c10 with a stage 4 cam and 4K stall? Low profile tires
Who makes the hood latches/hold downs that are on the Firebird?
Hello i have a 2020 tahoe z71 5.3L and i want to install the lt4 blower on my stock powertrain is it possible or there are any upgrades that i must do ?
Thanks
How you get a cruise to work in a 86 square body with l83 8l90 swap
How hard would it be to swap a l86 8 speed to a 2001 Silverado
I’m curious too, ?
I didn't put two and two together. You all sound and look the same. Small world. I'm just down the road about an hour and a half from Jason's shop
Ok fellas I have an lt1 ready to be swapped on my 69 Firebird. How can we touch base
what floor shifter in the firebird?
I have the LT1 10speed in a jk any chance in the future of putting that gauge set up and center console in a JK ?
Its possible for sure
Hello there i have 1983 c10 and im swapping L83 and 6l80 but i only need is a standalone harness can you sell me one if is it available ?
How can I get a hold of you guys?
What exhaust did you end up with Mitch?
14 inch magnaflows thru 2.5 inch exhaust
Is it possible for C6 to swap the LT1 engine?
I'm sure it is. But why would you want to? Genuine question, not trying to come off as an asshole
Any way to contact y’all ?
Swaptimeusa@gmail.com