ฝัง
- เผยแพร่เมื่อ 9 ต.ค. 2024
- Did this video helped you? Support CameraRestore for more free contents here:
www.buymeacoff...
Canon 1ds Mark II shutter speed replacement time-lapse repair DISCLAIMER:
CameraRestore is not responsible for property damage or injury incurred as a result of the information contained in this video. CameraRestore recommends safe practices when working with power tools and electrical equipment, use of lubricants, liquids, expensive electronics, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of CameraRestore, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not CameraRestore. Only attempt your own repairs if you can accept personal responsibility for the results, whether they are good or bad.
I just want to thank you for this video. Helped me to replace shutter on my camera.
Hey, glad to see that this old video can still give some good advice!
Thanks for making this video. Although you were replacing the shutter, I was able to get a look at a piece that I wasn't sure if was cross-compatible. I need to replace the power PCB in the camera and this helped me determine that I could replace a part from a 1d mark ii.
Thank you so much for this detailed instruction! I managed to replace the shutter charger base on it. Your skill is impressive too - no single unneeded screw touched. Would be better if it was better filmed however it did cover all the points that I encountered during my repair work (If watched x0.25 speed and very carefully).
Hey, thank you very much!
I’m really glad you have made it. It is one of my very first videos and the quality is quite poor, now I have better cameras, I will put more good contents soon.
Woah this is interesting! I just changed my father's 1Ds Mark ii's shutter last year.
Shawn Kurnia is it hard
Thanks for the video. I wanted to see if I dared to disassemble it, but I'm not going to do it... ufff too many connections and screws.
The problem with my camera is that horizontal lines appear in the photo.
If you can give me some advice I would appreciate it.
Hey, it is a common problem with this camera, might be image sensor damage or oxidation. I must say, not an easy job for this kid of issue. Where are you based?
@@CameraRestore thanks for your answer. If the fault is in the sensor, the repair will be very expensive. The photos come out with some horizontal lines, as if they were interference, and more visible at high iso. If you want I can send you some photos. Thank you so much.
hey
i got a 1ds ii that viewfinder display is gone, won't focus, err 01 when press shutter, without lens err 99. sensor cleaning mode also err 99. the mirror/mirror motor doesn't move at all during all these.
i took it apart this weekend just before taking the mirror box out, which i haven't figure out. I looked at circuit board and it seems good. little fuses are all intact. maybe it's the mirror motor assembly? i even took apart the contact pin after getting that module out and checked all and it's fine. camera can play back previous taken picture and top LCD works fine and can detect lens aperture before pressing shutter button. previous owner said the error happened during a lens change and viewfinder went dead and gives err 01/99. hopefully to hear from you. i'll spend a little more time diagnose it before selling separate parts hehe.
How much for Canon Eos 1 DS Mark III for parts . I have one non working unit.
Hi I’ve watch you video, thank you for sharing it.
I’ve got a focus problem on my 1dsii
It won’t focus. It just hunts. Then if it does lock focus it is only on the lower focus point.
Really strange. At first taking the battery out and restarting it would sort it but now Im limited to manual focus only.
Do you have any ideas?
Thank you
john robert
Hi thanks for passing by
That’s a strange one... Might be a connector oxidation... It a common issue.
Hi there, my 1d mark ii N is not throwing up an error code but rather just simply does not raise the shutter when you shoot and records a black image. Does this shutter require replacing or is something else the issue? Thank you kindly in advance for any response, Rod
Hi there, most likely is the shutter, also that’s why it gives you the error message.
great job!
Didn't you have any problem with the mirror? My mirror folded up while removing the mirror house. I see you left the body cap on, did you ever check this?
jpsholland, you're lucky, I'm working on one at the moment. Is quite difficult to explain but check the pictures in the link below. On the pic #1 push that black lever marked with the circle, it will get in position as in picture #2, the mirror will get back in position. Good luck.
ibb.co/h34yAy
ibb.co/dgUWVy
May I ask you when the shutter fails, when you try to shoot, does it make a strange sound?
hey, not necessarily but might do. In order to understand better if it is about the shutter or mirror, set up "mirror lockup" on your camera and take a shoot.
to turn on this setting, have a look here: support.usa.canon.com/kb/index?page=content&id=ART158597
with this setting, the camera will first lift and lock the mirror, by doing a second shoot, the shutter will open and expose.
Make a shoot in manual mode with a low speed and see what comes up.
@@CameraRestore thanks for this valuable comment. I must say that this is not possible because the camera just stays stuck with err99 showing in the upper LCD and does not allow you to go to the menus. Is there a way to lock up the mirror without having access to the menus?
If not, why can't I do this? (if there is a reason). Maybe it is not possible.
Essentially when I turn on the camera I hear the sound, it is like a cat screaming when scared with a mixture of feisty thundarstorm or something like that lol. It happens when I turn on the camera and also every time I try to press the shutter button.
I must say also that the first time I tried to lift the mirror and noticed the shutter blades were dodgy. On the next day tried to do it again to take some pictures and the mirror was like locked. I can't lift it anymore.
Read somewhere that it could be a capacitor but no sure why I capacitor would make the camera do this. If the blades/shutter looked dodgy it might be stopping something happening and hence the noise. Don't know.
Any further comments and suggestions are welcome. I am tempted to open the camera.
my 1 Dx mark 2 sensor will be damaged by laser light so how much money are required to purchase new sensor
Did you sort it out, not expensive considering the age. If you’re from UK I can help.
Hi! How different is the Ds MkII from the 1D MkII? I need to replace a shutter on the latter...
Manoel C.
Hi, mounts the same shutter.
@@CameraRestore Thank you so much, it works beautifully! I just replaced mine without any issues thanks to your video :)
@@mdasilvac
Hi I'm happy you've made it, could you be so kind and visit this page of mine to answer to a small poll. Would be really helpful to me. Thanks
fixyourgear.com/page-16/
Halo name is saleh.
1 DS Mark ii i while broken...and broken Shutter count the cost. Request in response. And whether device there is in there
alfin art photo - hi, sorry I don't understand your point, can you please be more explicit.
Best.
hi wich city are you in uk i want to make maintenance of my camera please
CAmerAfrique - Photographie - hi, sorry for late reply, did you sort it out?
could you send me all plugs the cables i mean colors and places first over the card slot.THX
Marek Wojcik do you still need the wires diagram...?
Hi.Yes i need it. Could you send me that please?
ibb.co/ixe6j5
hope it's the right one for your needs ;)
i now this wires diagram do you have more?
My Canon 1ds mk ii on;y lets me tak 1 picture, and thn it dies !! Wnen I try to view the image in RBG it only shows colord verticle lines. and I never see a picture, the rear viewr is black
zedieliam
Hmmm, looks like water damage, could be also a main board issue.
thx
And one wonders why it cost so much to replace a $50.00 shutter.
IF Canon made them right the first time you wouldn't need to get it repaired..
Err-99 on my Canon EOS-1DS Mark II, wound up is a bad shutter.
well, I believe that the camera made quite lots of shoots before failing... There are few things that might reduce the lifespan of a shutter but dust definitely is the most common.
repair mine hehe
Usui Akira did you repair it?
Did the video help?