My Acuvance Xarvis XX / RAD ESC Tune
ฝัง
- เผยแพร่เมื่อ 18 ก.ย. 2024
- Hello! Hope you like the video!
Chances are you’ll need to adjust this tune for your car, but it should be close enough so minimal adjustments can be done to fine tune for your car!
The motor in this video is the Agile 10.5T with a Torque Rotor. - ยานยนต์และพาหนะ
Wow! So much customization in this type of setup! 👏👏👏👏love learning this stuff it helps me see what I should end up getting and how I can set the car up. You’re an amazing driver! Thank you for sharing these settings! 🙏🙏👏👏👏
Thank you!
Great little vid 👌🏼 more technical points explained like this would be great. Subscribed 🫶🏻
Thank you
Great setup, I had qui similar setup on my xr10 stock spec. But boost rpm range was wider. Tried yours and it really work great, Thanks! Juste a quick note, you are talking about turbo activation rpm, but your turbo is set as trottle only. Im pretty sure that rpm doesn’t apply.
I saw your videos of your new z at super g. The angle you are taking with this chassis is unbelievable. I would gladly appreciate a specs video of this particular chassis
Hope it’s understandable but I don’t share all of my chassis 😅
your video is very helpful for beginners, learn from something right. thank you... please make a video about setting up the futaba cd700 servo and gyd550 gyro.🙏🙏🙏
Thanks for this video! Great information.
No problem! Hope it works out!
very good share, exactly what i need
This was awesome. Do you have any plans on doing spring choices as well as shock oil weights?
I’ve not really thought about it. Different cars require different setup directions
Gyro tuning video(s) would be cool too
Maybe in the future!
Could you do a video showing how to tune a Rad manually with Esc? Thanks
i got the rad w agile motor and i set my initial settings per instructions now i dont have reverse... any suggestions?
You need to hold on button on esc it will blink then you can calibrate the end points on your remote
Cool video! Can you tell me what kind of shock oil you use? And what springs?
any chance of a vid with you installing all of the capacitors :)
No I don’t like soldering 😂
Got a problem, can you help please? Connected xarvis xx and a-bus, futaba 7px. Everywhere the latest version of the update. Show everything except the temperature of the motor. Fledge motor, fully working
Hi Vittorio,
The wiring go close to esc or battery?
What is your gearing?
I just upgraded to the s.bus and went through all the updates required on the rx/tx & esc. Everything was working as it should. I then followed your tune on this video. Did one hit and now the motor won’t spin and all the lights on the esc are blinking. Please help! Did I just blow up my motor???
Sounds like a loose sensor wire, this is a pretty conservative tune.
You should also unplug the esc from battery for a minute and then recalibrate after an esc update.
Yes that was my first thought as well so I replaced the sensor wire and same issue. I did some further digging and my rotor disengaged inside and took out the sensor module with it. Another 90$ down the drain let’s hope that it can be pieced back together 😢
I run this tune since 5 months ago every weekend without problems,it runs very smooth and I love it..Maybe you ran too much can timing on the motor,I run 20 degrees on the can....Or maybe you just had a bad rotor,it happens sometimes,pretty sure this tune has nothing to do with your rotor failure since is not agressive at all.
What acuvance rotor is better torque or rpm whats the diffrence bro
It depends on your track size
Interesting settings on timing, how does that translate to trigger feel? you have no additional timing up to 12k rpm and also above 21k unless you full throttle. does this give your low and high throttle more resolution and less puch in a way since you don't have the extra timing kicking in?
I find not needing anymore timing after that. We’re on a slippery surface after all!
What software version allows BEC tuning through the s.bus?
I’m not sure, mine is the latest version of Xarvis XX
The Xarvis XX is the only one with adjustable BEC voltage. not available in Xarvis and Rad
What’s your motor timing at ?
20-32 depending on the track