2017 Ford Transit Tourneo Custom...Noisy Gearbox, Can We Fix It...

แชร์
ฝัง
  • เผยแพร่เมื่อ 30 ต.ค. 2024

ความคิดเห็น • 88

  • @Bobbajobb956
    @Bobbajobb956 4 หลายเดือนก่อน +1

    Just fixed my gearbox with the same bearing problem! Just that one bearing made my van sound horrendous!! Really thought I needed a full rebuild or replacement box but this video gave me the idea to try and replace it and it works absolutely perfect now! Many thanks for this video and not to mention the money I have saved! 👍

  • @vincentyerkess7230
    @vincentyerkess7230 ปีที่แล้ว +9

    Great video.
    I think I know all about that gearbox now 🤣
    You make it so simple

  • @johnchincotta1qwdb15
    @johnchincotta1qwdb15 ปีที่แล้ว +4

    Another cracking video Alan,you certainly know the tricks of the trade.

  • @ROUTEPLANNERPAUL
    @ROUTEPLANNERPAUL ปีที่แล้ว +3

    A gearbox for ebay ... well done Alan big happy new year to uou and the best of health

  • @neilobusk
    @neilobusk ปีที่แล้ว +1

    Scary and crazy one bearing can cause this....
    In depth and interesting..... as always
    saturday night sorted for me... insignia vid next....
    Best wishes..
    N x

  • @jospeters7558
    @jospeters7558 ปีที่แล้ว

    Thank you Alan, 👏👌👍 the Stealership sold you a rebuilt gearbox for 3000€ for only one broken bearing

  • @alankeane4059
    @alankeane4059 ปีที่แล้ว +1

    2 videos in 2 day wow keep it up Alan.

  • @andymorgan5190
    @andymorgan5190 ปีที่แล้ว +1

    thanks Alan, nice job for the afternoon, fingers crossed youve just saved me a bomb

  • @stephenegginton7590
    @stephenegginton7590 ปีที่แล้ว +1

    Great video Alan another gear box saved hope you are well and had a good new year 🎉❤

  • @mikewilson631
    @mikewilson631 ปีที่แล้ว +3

    It strikes me that the gasket will be part of the calculations of end float on the gearbox shafts. Without it, there will be excessive preload on the taper bearings on each end of those shafts. Would take some time but I would expect those bearings to fail earlier than they should - might be a tad noisy, as well.

    • @andrewmicas4327
      @andrewmicas4327 ปีที่แล้ว +2

      The Ford boxes used have Belville spring washer behind outer taper race so that was the pre-load. Early escorts with larger engines that had the clutch dropped hard, flattened the Belville washers. First symptom was damaging speedo gear. Those and worn camshaft etc. paid off my mortgage in 10 years. These were done after work at nights loved the Fords good to repair, plus rusty bodywork.🤣🤣🤣

  • @damiankimmins3880
    @damiankimmins3880 ปีที่แล้ว

    Great video Alan! Get that guard back on! 👍

  • @TheDaf95xf
    @TheDaf95xf ปีที่แล้ว

    Morning Alan Mr mondingo man 😀 Love the Bobby hat 🤣 Always fascinating watching you do your suff 👍🏻

  • @ianwheat1577
    @ianwheat1577 ปีที่แล้ว +2

    Thanks good video same sealed bearing why are they sealed and not like the others which are good lubricated from gear oil think ford put that one in to keep you busy

  • @cliffordpedley3216
    @cliffordpedley3216 ปีที่แล้ว

    Hi there I did watch the other video of you doing the gear box bearing but my One it jumps out of 1st and a bit of a wine but it still drives perfect in all the other gear I have a 2012. Mk4 diesel estate I don't use the car every day and only go a few miles in it we have got some other cars so I will use it until I have to do it I am a Lorrie driver so as are mechanics say I will let it develop I will check your video on how to do the selectors on the gear's great job

  • @patkelly7999
    @patkelly7999 ปีที่แล้ว

    Great autopsy Alan, and fix💯 sorry way behind on vids, but will catch up, hope the hols are going well, take care👌🙏👍🙂

  • @gazhightower4264
    @gazhightower4264 6 หลายเดือนก่อน

    Thank you for your video. I'm contemplating buying a 17 plate 4x4 transit with a grinding rattling noise from gearbox 🤔🧐 I wonder.

  • @andreottimarcio
    @andreottimarcio 8 หลายเดือนก่อน

    Ótimo trabalho, qual óleo utilizado nessa caixa é de 6 ou 5 marchas?

  • @jezequelelisabeth
    @jezequelelisabeth ปีที่แล้ว

    Hello and thank you very much for this video. I have the same problem. Same comment as other people about fitting a sealed bearing. My level of English does not allow me to understand the comments. I have a few questions: type of thread lock used, tightening torque of the screw and where you position the magnet in the box when reassembling. During disassembly it fell. Thank you very much for an answer. I use google translate.

  • @tiguanman1170
    @tiguanman1170 ปีที่แล้ว +1

    In the "real world", a vehicle wouldn't reach 200k where the bearing might fail. A Ford would either be scrapped due to corrosion or the cost of a DMF and clutch. Alan's vehicles are different because they run up a huge mileage in just a few years. Useful information for Ford themselves.

    • @alan4x
      @alan4x  ปีที่แล้ว

      very true, cheers tiguan

  • @miketherefurbisher8000
    @miketherefurbisher8000 ปีที่แล้ว

    A BIG Thank you Alan!!👍

  • @metalworker007
    @metalworker007 ปีที่แล้ว +3

    Looks to me the only bearing in the box that is sealed both sides ..the others are open to the gearbox oil ...perhaps that's the fault..maybe one seal should to be removed, to save the bearing spinning in its own detritus..not getting washed out with clean oil constantly like the others...thanks very much Alan, excellent video ..is that an mtx75 box ? f so, maybe you should mention that somewhere.. and i don't know on my connect mtx75 box ..there seems to be a plate over that bearing ..like it could be changed with the box still in the van?

    • @MotorwiseBromley
      @MotorwiseBromley ปีที่แล้ว

      beat me to it

    • @retro423
      @retro423 ปีที่แล้ว

      It might be that it's in a position that the oil can't get to it hence using a sealed for life bearing

    • @marinusapeldoorn6631
      @marinusapeldoorn6631 ปีที่แล้ว

      I had the same thought Metalworker😁

  • @saurannuraliyev1695
    @saurannuraliyev1695 ปีที่แล้ว

    Happy New Year!

  • @paullynch1938
    @paullynch1938 11 หลายเดือนก่อน +1

    You’ve just earned yourself another subscriber my man , very good

    • @alan4x
      @alan4x  11 หลายเดือนก่อน +1

      thanks paul,much appreciated

  • @jimagnew1305
    @jimagnew1305 ปีที่แล้ว

    I have a 2.2 Custom and the gearbox is changing gear beautifully however the whining noise is horrendous. Im guessing this is same problem. I would have loved to hear the sound before and after. Are all custom gearboxes the same?

  • @jimbojombo4464
    @jimbojombo4464 ปีที่แล้ว

    Might be abit of a repeat Alan but we love your videos

  • @byronmills5952
    @byronmills5952 ปีที่แล้ว +1

    A truly excellent video.

  • @ceannscriobh
    @ceannscriobh 6 หลายเดือนก่อน +1

    Great tutorial.. thank you..

    • @alan4x
      @alan4x  6 หลายเดือนก่อน

      😊

  • @subaru21175
    @subaru21175 ปีที่แล้ว +1

    How much was the bearing??

  • @finnhogan7889
    @finnhogan7889 ปีที่แล้ว

    Hi Alan 👋 Great work Again will Surely Help somebody cheers 🍻

  • @zzhughesd
    @zzhughesd ปีที่แล้ว

    You and your Forks Alan. Doesn’t seem like yesterday you were on that Mondy

  • @LeeLeesAdventures
    @LeeLeesAdventures ปีที่แล้ว

    Great video thanks for posting and you made it look so easy. Great filming i have the transit custom 2019 2.0 euro 6 its only done 15k so i am a long way of 250k lol. Question how do you know the oil level is ok in the transit gear box. On ford over many years you take out the oil level plug and if it drips out its ok. I have been told its different on the ford custom. Could you tell us or do a video on how you check it much appreciated. Michael nottingham 👍

  • @deandempsey264
    @deandempsey264 ปีที่แล้ว

    Would it be worth opening that new bearing and exposing it to the gearbox oil

  • @Roverturbo
    @Roverturbo ปีที่แล้ว +3

    Interesting that the only bearing in the box with a nylon seal, is the only bearing that has failed in both boxes. 🤔
    I aways remove the nylon seals whenever I replace them.

    • @marinusapeldoorn6631
      @marinusapeldoorn6631 ปีที่แล้ว +1

      I can't figure out the function of the seal unless there is some kind of grease in the bearing & the normal gear box oil can not reach the rollers ...... Sharp thinking RT

    • @Roverturbo
      @Roverturbo ปีที่แล้ว

      @@marinusapeldoorn6631 definitely grease under there… but how long will that last.

    • @marinusapeldoorn6631
      @marinusapeldoorn6631 ปีที่แล้ว +1

      @@Roverturbo not long enough that's for sure now😁

    • @Roverturbo
      @Roverturbo ปีที่แล้ว +1

      @@marinusapeldoorn6631 you still have to remember, that box had over 200k on it.

  • @tommysmith993
    @tommysmith993 ปีที่แล้ว

    Have you got any videos of taking Kia Sportage box apart?

  • @Elvis35-77
    @Elvis35-77 ปีที่แล้ว

    "Moon Bearings, Rougher With Each Mile, I'll Grind you Out With Style Someday......."🤣🤣🤣

  • @azertyy3978
    @azertyy3978 ปีที่แล้ว

    Hi Alan, do you perhaps know if a gearbox bearing can be replaced seperated? I own a Ford Focuys 1.8TDCI from 2005, and while driving the car I hear a humming noise. When pressing the clucht while driving the sound is gone, by releasing it comes instant back no matter what gear. I noticed how higer I rev the car the more noise it makes.

  • @the1beard
    @the1beard ปีที่แล้ว +2

    that bearing doesn't need a seal
    appears to have got hot and removal of the seal would mean the oil would get in if the seal was removed
    it would last a lifetime

  • @abderrahimhaddanitankioupr9367
    @abderrahimhaddanitankioupr9367 ปีที่แล้ว +2

    THANKIOU

    • @alan4x
      @alan4x  ปีที่แล้ว

      😁

  • @2006chame
    @2006chame ปีที่แล้ว

    alan, mondeo 2023 not coming to europe, whats your opinion?

  • @aleynagrace2968
    @aleynagrace2968 ปีที่แล้ว

    Ford Mondeo automatic box,there is an interior filter inside,Could you please explain how to change it?,ive tried to change it multiple times but i cant,could you please explain sir?,thank you.

  • @stephenhurrell2773
    @stephenhurrell2773 10 หลายเดือนก่อน

    How much do you charge to repair a gearbox
    Where in the U.K. are you

  • @jamesholness5657
    @jamesholness5657 4 หลายเดือนก่อน

    How much where the replacement parts

  • @sarahmerritt7607
    @sarahmerritt7607 ปีที่แล้ว

    Excellent very good video sir👍

  • @andrewjames7616
    @andrewjames7616 ปีที่แล้ว

    Thankyou Alan 👍

  • @bartoszk4812
    @bartoszk4812 ปีที่แล้ว

    Good video Alan!! 👍

  • @stevensmi1167
    @stevensmi1167 9 หลายเดือนก่อน

    Why use a sealed bearing in a box that has open bearings in oil and the sealed ones failed. I’m currently changing a sealed bearing in a Ford ranger 2015 gear box!!

  • @zzhughesd
    @zzhughesd ปีที่แล้ว

    What causes the pitted bearings , are they coated and not one single material ball ?? Is it grease breaking down the cause of the pitted ness. Do I take it expensive bearings don’t break down until moon miles ???

    • @isbemorph
      @isbemorph ปีที่แล้ว

      I'd say the bearing was fitted too tight. If that was a cone bearing with a tiny hair of play it would last forever.
      [edit] 6:06 these three bolts hold the bearing but also preload it. So the bigger the torque, the more the balls are squeezed between the outer and inner race.

  • @jounipenttila9908
    @jounipenttila9908 ปีที่แล้ว

    Very good video. Thank you!

  • @scotthawkins1011
    @scotthawkins1011 ปีที่แล้ว

    Brilliant video,👍

  • @Neverquit12
    @Neverquit12 ปีที่แล้ว

    Where’s your garage pal as I’ve got the same issue with my food focus

  • @Fritsvrolijk
    @Fritsvrolijk ปีที่แล้ว

    Nice job Pro

  • @daveast01
    @daveast01 ปีที่แล้ว

    Another top vid.

  • @RemusKingOfRome
    @RemusKingOfRome ปีที่แล้ว +1

    Just think, modern EVs don't have to worry about "Transmissions" K.I.S.S. :D

  • @mondodaftasabrush
    @mondodaftasabrush ปีที่แล้ว

    I thought you would have picked the seal out for inspection before your attacked it with Freddie five inch
    Bearing seems to be a common fault maybe poor quality bearing supply or is wrong application putting a sealed bearing within a gearbox think I would either of removed the seals or one for the oil to circulate through it
    Maybe have this conversation in another 250 thousand miles down the road.... Till the next time. See yah !

    • @FatHead1979
      @FatHead1979 ปีที่แล้ว

      Personally I'd be leaning towards it being scenario 2, FAG make OEM quality bearings and using a sealed bearing in the way Ford have, doesn't seem like a good idea to me. Although with 200K+ on the box, maybe Ford aren't bothered because it's well outside its warranty period.

  • @iantaylor1172
    @iantaylor1172 ปีที่แล้ว

    Do you not get bored working on cars all day? I know I do.

  • @molajat6133
    @molajat6133 ปีที่แล้ว

    Does anyone know where I buy a injector puller for MK5 mondeo 2.0 diesel?

  • @nialldaleo6544
    @nialldaleo6544 ปีที่แล้ว

    Alright Alan,I was wondering could you give me an idea about two dead passenger doors ,front and back,the windows and central locking not working on mondeo mk4 ,I checked all the fuses,and changed driver door and passenger modules but the problem remains, if you have any experience with this problem I would appreciate it thank Niall

    • @isbemorph
      @isbemorph ปีที่แล้ว +2

      Pull the door panel and check if a module gets its power and ground. If not feed it with +12V from the battery to see if it starts working. I had such issue, it turned out to be a corroded power cable inside the rubber grommet sleeve between the body and the door.

    • @nialldaleo6544
      @nialldaleo6544 ปีที่แล้ว

      @@isbemorph A thank you @Mr Thomas I will give that ago ,thank you for your insight
      Niall

    • @marinusapeldoorn6631
      @marinusapeldoorn6631 ปีที่แล้ว

      I believe each door has its separate fuse in the boot. Maybe the fuses are not supplied with the necessary 12 volts. I'd start measuring in the boot first.

    • @CrimeVid
      @CrimeVid ปีที่แล้ว

      So you’ve stopped putting chopped up tights in the noisy ones then ?

    • @CrimeVid
      @CrimeVid ปีที่แล้ว

      If that is such a bad bearing materials wise, can you buy a better(aircraft quality) bearing for it ?

  • @TruthTortoise81
    @TruthTortoise81 ปีที่แล้ว

    Intentionally or otherwise, Ford will always design an Achilles' heel into everything they manufacture.

  • @frednetherlands887
    @frednetherlands887 ปีที่แล้ว

    Great!

  • @piotrolejnik9324
    @piotrolejnik9324 ปีที่แล้ว

    Mam luz na kielichu z lewej strony bardzo duży co może być uszkodzone

  • @lovepreetsinghhanjra1997
    @lovepreetsinghhanjra1997 ปีที่แล้ว

    👍🏻👍🏻👍🏻👍🏻

  • @mondodaftasabrush
    @mondodaftasabrush ปีที่แล้ว

    Mmmmmm. Furry iron fillings
    Happy New Hammer 2023. Soft face posh

  • @stevenburns989
    @stevenburns989 ปีที่แล้ว +1

    the bearing is slovakian, had it been a koyo, it still be good

  • @khennahsfarm2610
    @khennahsfarm2610 ปีที่แล้ว +6

    Im also noisy ,hubby..just to let u know😉