Great job it's nice to encounter how to videos like this that teach newbies how to make accessories that will benefit them on more complex projects thanks
FYI - the Dremel Moto - Tool Model 395 Type 4 has a 1/2 inch 12 TPI curvi-linear plastic nut on the business end. THAT can be replaced with a Hex-headed Plastic Pipe adapter. Buy a white plastic 1/2" Female Threaded ADAPTER (female threaded to glue on end) and that 12 tpi fits the Dremel Moto-Tool. Cut off the smooth glue on end down to the shoulder. THIS works and gives you a Hex end on the Dremel tool. Cost under $3 at any hardware store.
Great project! as usual very well explained.. I want to make one... first I need a Dremel... and a lathe... and a mill... and a.. lol. Thank you for another awesome video
By cutting a slot on the otherside of the main hole you created a stress point. You could cut a hole in the end of that cut with an end mill to prevent a crack from forming... nice tool otherwice
Haha, really, i got this two plants in workshop like 10 years, they almost die in our livingroom than put it in workshop and start growing again, look like they like soil full of aluminium chip ;-)
Very nice idea, thank you for posting. I have just finished making mine - not as pretty as yours, I don't have your tooling, be that as it may I managed to get it right with hand tools. This will add a whole new dimension to my mini lathe!
Great to hear that, thanks, yes i complicated a bit wit that one, because of video need, i got one before that, make out of steel in about 10min, it waa ugly but just as functional as this one.
hvala, mal po mal pa se nabere, dejansko mam neka orodja od 5 razreda ko me je začel zanimat modelarstvo in elektronika, mehanika šele pred nekje 10 leti
čedno, res maš en kup strojev ki vzbujajo zanimanje, projektov pa tudi dosti :). Itak pa vsi ki te poznamo vemo, da obdeluješ na nivoju kot delajo tavlki strugarji :D!
Thabks man, i don't own any dremel yet, but own lot of proxxon tool, and happy with any single piece, i try a few unknown brand but they'r far far behind proxxon, dremel is good they say but i don't like their design, this small drillls heave such a "fat" handle, no front mount for holder like this, you can see there proxxon got 20mm steel mounting ring behind rhe chuck... I deffenetly say proxxon, but no 220V/110V i prefer 12v tool, because it got much much more torque on low rpm, i can drill aluminium with that drill 3,2mm with lowest possible rpm and it still turning try to do that with 220v, it will drill only on full rpm, the power is same (like 100w) but manufacturer don't tell you on which rpm power is measured, you don't need full power on 12000rpm, you need power on low rpm, that's why choose 12v.
There are some videos about my mill, like making fly cutter, test boring head, test facing head from banggood, but video about igaging dro instalation is almost all about the mill. This is basic chinnese mill, you can get it by many many different brand, just with different add on, paint, stickers and so on, same story as mini lathe. Myne is brand px tool 25lv (l mean lonv table and v mean vario - automatic x axix support) Just google it as "mini or table mill 20 or 25 than because two of the letters is different from brand to brand, here in eu most common brand are optimum.de or bernardo.at but also can get some no name brand like mine for half the price (yep same mill but no brand) i was really lucky to get this one bearly used for 1000€ but it got automatix x support (cost about 300€ if you bought separatly, i got lot of gadget and tools with and the most importand it got MK3 konus into spindle, it's hard to get that small mill with mk3 lot of them got mk2 konus so you can't use so many tools, max mill diameter for mk2 is 16mm, for mk3 is 20mm.
Nicely done. but IMHO one point around time 0.50 should be emphasized... the hand drill tool shaft, should be at CENTER on a lathe. so the measurement should be taken between lower plate of cutter handler and the drill tool shaft.
True, thanks for info but i got quck change tool post on lathe, so setting a heigh to a center is no problem for me. simply insert some small drill or something into a proxxon/dremel chuck and set height on center to piece into lathe chuck.
@@TinC33 I was looking a proxxon's micro mill, I'd want to make a small fly cutter for thank god the use a standard thread, dremel uses some BS .276x40 thread
Pozdravljen v al-cu kamnik majo vse barvne kovine, tam nabavljam, včasih pa se tja tudi zapeljem pa nakupim mal "refuzo" robe, razne ostanke ki jim ostanejo od odrezov, prodajajo po nižjih cenah.
@@peterobreza1008 tam okol 6e, sem ravno prejsbji teden narocu mal palic, pa neke profile sem rabu, ca20e robe, bo precej casa dovolj za stružit taka igranja kot se sam grem.
@@peterobreza1008 Hvala, ma ne to je nekakšna izpeljanka iz hobija modelarstva, začelo se je ko sem kupil stružnico za delat sklopke za čolne, pol pa en mali rezkar, pa večji... ampak še zmeraj samo hoby, pa združil hobije na kup, kot so modelarstvo, strojništvo, elektronika, zraven pa še mal snemanja in montaže, pa pride še kaka nagrada za povrhu, zaenkrat mi je čist super, drugač zares pa hodm na šiht hot štromar vzdrževalec, pop pa furamo kmetistvo tak da mal časa zmanjka za videje...
thanks Graeme, do you ask if i mind if you make one? c'mon, it's here to give people idea, to make themself, really usefull tool and so easy to make, i complicated a bit with this one, because of filming, but once i need quickly i make one in about 10min out of steel.
![Making of: Small precize lathe tool out of broken drill bits [M4 internal thread cutting]](http://i.ytimg.com/vi/k2a9ywCEK_A/mqdefault.jpg)
![Making of: Small precize lathe tool out of broken drill bits [M4 internal thread cutting]](/img/tr.png)
That's a great holder for a Dremel type tool - very useful for small milling
That looks very useful, thank you. 🇬🇧
Perfect!. I don`t who give 58 dislike! There is great effort and kindly share his knowledge! They must be thankful!
Thanks, many people see some wrong details, like no wearing googles, or end mill into drill chuck and hit dislike...
That's a terrific idea and impressively made. I definitely have to make one of those.
Great job it's nice to encounter how to videos like this that teach newbies how to make accessories that will benefit them on more complex projects thanks
Thank you! Cool accent mixed with creativity and ingenuity. You are the man!
Thanks man, grettings from Slovenia
Well done, thank you for sharing this.
Well done! I'm sure there are more people than just myself who would love to hear more about the anodizing process (please)!
Fantastic work, well done
Good video, and a nice tool holder. Nothing beats making a specialized tool!
Dan Moreton thanks
FYI - the Dremel Moto - Tool Model 395 Type 4 has a 1/2 inch 12 TPI curvi-linear plastic nut on the business end. THAT can be replaced with a Hex-headed Plastic Pipe adapter. Buy a white plastic 1/2" Female Threaded ADAPTER (female threaded to glue on end) and that 12 tpi fits the Dremel Moto-Tool. Cut off the smooth glue on end down to the shoulder. THIS works and gives you a Hex end on the Dremel tool. Cost under $3 at any hardware store.
Very nice work
Beautiful work ! Very simple and useful. I like it .
Thanks
Hello, excelent video. This tool have enougt power to drill a hole in steel? or cut a steel bar?
It can but only up to about 2mm, 3mm is for wood aluminium and brass only.
@@TinC33 thank you very much!
Excellent video. I love the reused sawblade mod too. I can think of a lot of ways one could use that Dremel/lathe combo.
Great project! as usual very well explained.. I want to make one... first I need a Dremel... and a lathe... and a mill... and a.. lol.
Thank you for another awesome video
Very nicely done - well explained video. I’ll soon be making one for my Dremel. Thanks!
thanks
Me too sr.. awesome!
Merci pour vos idées de génie….
This is a great and very usefull tool! I will make one myself as well. Thanks for the explanatory.
By cutting a slot on the otherside of the main hole you created a stress point. You could cut a hole in the end of that cut with an end mill to prevent a crack from forming... nice tool otherwice
Claes Wikberg great idea, thanks, it eaven look nicier, but anyway i think there is no way to broke it.
Thumbs up! Its plain, simple and useful tool. Thank you.
Impressive Machining and tooling
Thanks
Please show how to paint the aluminium. What chemicals needed and what paint you use.
I need this!!
I will make video once about anodising, but there is already lot of video about, just search "anodising aluminium"
Cool video, thanks! Buy the way, it is the first toolshop with plants I have seen 🤗
Haha, really, i got this two plants in workshop like 10 years, they almost die in our livingroom than put it in workshop and start growing again, look like they like soil full of aluminium chip ;-)
Great job. Just what i can use. Thanks for the video and the drawing.
Thanks
Very well done!
What software did you use to make drawing?
I use here google sketchup (layout addon) but now we got solidworks on my full time job so i only use solidworks now.
Great tool you made here, I have to make one myself, thanks for sharing...
Thanks
Great work brother.
I'll make one myself now.
Cheers
Thank's a lot from France ;-) , Very useful !
Thanks
Good job, man!!!
Thanks
Very nice idea, thank you for posting. I have just finished making mine - not as pretty as yours, I don't have your tooling, be that as it may I managed to get it right with hand tools. This will add a whole new dimension to my mini lathe!
Great to hear that, thanks, yes i complicated a bit wit that one, because of video need, i got one before that, make out of steel in about 10min, it waa ugly but just as functional as this one.
As I have said before I like your work. I plan on making the same to use my Hilda rotary tool in my 13x40 lathe. Very Nice Work!
do you want to make a video where you explain how it is anodized? Work well 👍👍👍
S. Tre yes i planning to make it, but... wait on more free time, it's just a hobby for me.
tintek33 very good!
Molto bene🙂👍👍👍
i second that
Great work brother
Thanks
@@TinC33 welcome
Well done, looks great!
Thanks, but works eaven better ;-)
Great 👌👌👌👌👌
Great video, when are you released the video on anodized the part ?
thats a great tool holder i love it !!!
thanks
Great idea
Thanks
Benissimo!! ya me estoy haciendo uno!
nice machining there! Wish I could have a smale armory in a shop like that :D.
hvala, mal po mal pa se nabere, dejansko mam neka orodja od 5 razreda ko me je začel zanimat modelarstvo in elektronika, mehanika šele pred nekje 10 leti
čedno, res maš en kup strojev ki vzbujajo zanimanje, projektov pa tudi dosti :). Itak pa vsi ki te poznamo vemo, da obdeluješ na nivoju kot delajo tavlki strugarji :D!
very good video can you tell me where you buy adjustable boring tool head you showed to drill different size holes in metal please reply soon Thanks
Here
th-cam.com/video/Zgw3-NF33Q0/w-d-xo.html
Hi. Love your videos and of course your work. That’s a nice metal bandsaw. Can you tell me the make model and supplier. Thanks. Keep them coming.
Basicly it's not metal saw it's make for wood but it work with alu also
th-cam.com/video/pKgDt5Vwh4Y/w-d-xo.html
th-cam.com/video/J5prayVPErU/w-d-xo.html
@@TinC33 Many thanks. Appreciate your reply. Cheers
This is great, thank you!
thanks, where you from DE?
Looks even better than original proxxon holder for lathe (I got one) :)
Google+ SUCKS BALLS - the worst forced social network i didn't know they existed, will search for it now. Thanks
on this page - under accessories www.proxxon.com/en/micromot/24002.php
Great job. What software are you using to design your ideas? looks good.
Thanks, this software is google layout its part of google sketchup, but for 3D modeling i'm learning using solidworks now, much better than sketchup.
@@TinC33 thanks. i will give it a go
That was Fantastic
Can I have your opinion
Dremel is Petter or proxxon
Thabks man, i don't own any dremel yet, but own lot of proxxon tool, and happy with any single piece, i try a few unknown brand but they'r far far behind proxxon, dremel is good they say but i don't like their design, this small drillls heave such a "fat" handle, no front mount for holder like this, you can see there proxxon got 20mm steel mounting ring behind rhe chuck...
I deffenetly say proxxon, but no 220V/110V i prefer 12v tool, because it got much much more torque on low rpm, i can drill aluminium with that drill 3,2mm with lowest possible rpm and it still turning try to do that with 220v, it will drill only on full rpm, the power is same (like 100w) but manufacturer don't tell you on which rpm power is measured, you don't need full power on 12000rpm, you need power on low rpm, that's why choose 12v.
TinC33 thank you that helped a lot
Great! Thank you for sharing!
No problem, thanks
Awesome tool .Wil wait the Anodizing Video .The software for the Plans?Looks Fantastic
George H thanks, it's google layout great for 2d sketches, easy as paint
Really nice!
Thanks
Awesome!
Excelente amigo....
Tine, what mill do you have? I've seen a couple vids on your lathe but not the mill. Apologies if I just missed it.
There are some videos about my mill, like making fly cutter, test boring head, test facing head from banggood, but video about igaging dro instalation is almost all about the mill.
This is basic chinnese mill, you can get it by many many different brand, just with different add on, paint, stickers and so on, same story as mini lathe.
Myne is brand px tool 25lv (l mean lonv table and v mean vario - automatic x axix support)
Just google it as "mini or table mill 20 or 25 than because two of the letters is different from brand to brand, here in eu most common brand are optimum.de or bernardo.at but also can get some no name brand like mine for half the price (yep same mill but no brand) i was really lucky to get this one bearly used for 1000€ but it got automatix x support (cost about 300€ if you bought separatly, i got lot of gadget and tools with and the most importand it got MK3 konus into spindle, it's hard to get that small mill with mk3 lot of them got mk2 konus so you can't use so many tools, max mill diameter for mk2 is 16mm, for mk3 is 20mm.
@@TinC33 thank you very much! That helps me get an idea of the size and cost.
Thanks, great video! I have just one question --> what is the thickness from the tool? I need to know it, because I make one for a schoolproject.
I take 10 or 12mm aluminium plate, don't remember exactly
I measure now, it's 10mm
TinC33 okey, thx! :) great tool
Anodizing video, please!
Excellent
Thanks
terimakasih.. ide yang bagus
Hello, which milling machine do you use?
Px-tools 25lv basic mini mill 25 series (can be found by many different brand arround the world)
what mil do you use
Hello in what program was it drawn?
Google layout, this program is part of google sketchup, great to draw some fast sketches.
Thank you for your response
Why did you not immediately make a cassette into a tool holder with a Dremel mount?
you mean groove for mount direct onto quick change tool post, hey, good idea, but anyway i got enough holders, because i'll make it by myself
Nicely done.
but IMHO one point around time 0.50 should be emphasized... the hand drill tool shaft, should be at CENTER on a lathe. so the measurement should be taken between lower plate of cutter handler and the drill tool shaft.
True, thanks for info but i got quck change tool post on lathe, so setting a heigh to a center is no problem for me. simply insert some small drill or something into a proxxon/dremel chuck and set height on center to piece into lathe chuck.
What milling machine you are using.
Some chinnese version but tottaly the same as optimum bf25 just google for "bf25mill" i got version with long table auto x axis and mk3 konus.
what are the threads on the spindle?
What thread do you got in mind, rhere are no thread on lathe spindl if you mean that.
@@TinC33 your rotary tool. I did find it after a few hours looking m8x.75
@@pacman10182 ah ok, now i know ;-) i didn't know because there was original chuch since ever, max insert is 3,2mm
@@TinC33 I was looking a proxxon's micro mill, I'd want to make a small fly cutter for
thank god the use a standard thread, dremel uses some BS .276x40 thread
@@pacman10182 nice, great project
very nice gadget for dremel .....please one for me
Time 4:21 can you tell me how i make it
You mean anodising? Check on yt "anodising aluminium" i will make video about it once...
@@TinC33 thank you sir
exist original from proxon
where can we find the anodizing video? :)
show!!!
A mi poves kje kupujes alumini
Pozdravljen v al-cu kamnik majo vse barvne kovine, tam nabavljam, včasih pa se tja tudi zapeljem pa nakupim mal "refuzo" robe, razne ostanke ki jim ostanejo od odrezov, prodajajo po nižjih cenah.
@@TinC33 hvala a mogoce ves kaksna je cena na kilogram aluminija
@@peterobreza1008 tam okol 6e, sem ravno prejsbji teden narocu mal palic, pa neke profile sem rabu, ca20e robe, bo precej casa dovolj za stružit taka igranja kot se sam grem.
@@TinC33 hvala za odgovore rad vidim slovenca k na yt objavlja kakovostno vsebino, se drugače ukvarjaš z strojništvom ze dalj časa
@@peterobreza1008 Hvala, ma ne to je nekakšna izpeljanka iz hobija modelarstva, začelo se je ko sem kupil stružnico za delat sklopke za čolne, pol pa en mali rezkar, pa večji... ampak še zmeraj samo hoby, pa združil hobije na kup, kot so modelarstvo, strojništvo, elektronika, zraven pa še mal snemanja in montaže, pa pride še kaka nagrada za povrhu, zaenkrat mi je čist super, drugač zares pa hodm na šiht hot štromar vzdrževalec, pop pa furamo kmetistvo tak da mal časa zmanjka za videje...
Good!!!!
Такая приблуда продаётся у Проксона только выполнена она из стали я 4 года пользуюсь для закрепления бормашинки на токарном станке.
Good and how much it cost? I would not pay more than $10 because it's just sooo easy to make, for a simply version need about half of hour to make ;-)
03:27 anyone spot the "centre spreads" on the door
The perfect shop decoration!
Good…
Top!!!
👍
Thanks for this video, thumb up from me, but please stop the musik. Thanks
It's alright if you already got all the tools, otherwise,,
Он бы ещё из пластилина сделал.
TFS "thanks for sharing" great idea mind if I make one? Best Regards G :)
thanks Graeme, do you ask if i mind if you make one? c'mon, it's here to give people idea, to make themself, really usefull tool and so easy to make, i complicated a bit with this one, because of filming, but once i need quickly i make one in about 10min out of steel.
@@TinC33 guess I was trying to say I like the tool cheers G :)
Lol so much work.. $$$$$$ machines to make tool post..
Индус что ли? Такой английский дерьмовый.
what mil do you use
Px tools bf25lv basic mini mill, something like optimum, bernardo, grizzly etc.