The tricks and cunning thoughts of the skilled worker at work
ฝัง
- เผยแพร่เมื่อ 29 ก.ย. 2024
- Teaching metal turning, teaching general metal turning.
Innovative and new daily methods in the field of metal turning, the method of operating the metal lathe, and identifying all its parts and the laws of metal turning.
The tools used in turning metals and the method of preparing them for work.
Daily positions on a metal lathe
Daily innovations on the metal lathe
Components of teaching metal turning, teaching general metal turning.
Innovative and new daily methods in the field of metal turning, the method of operating the metal lathe, and identifying all its parts and the laws of metal turning.
The tools used in turning metals and the method of preparing them for work.
Daily positions on a metal lathe
Daily innovations on the metal lathe
Components of metal turning workshops
The most important daily repetitive tasks in the field of metals
I wish I'd known more Men growing up, known mor People with skills like this that I could learn from. As it was, I was raised by a bunch of Women, never had any Male role models and have to self-teach myself just about everything. I'm a good laser engraver/cutter now and am looking to add a CNC router to my toolset soon, then into plasma cutting. Hoping to have a lathe like this at some point as well- one step at a time though!
Электросварка заземление через подшипники шпинделя?
Я тоже об этом подумал!!))))))))))))
А чего нормально потом немного бить будут😂
Soldar arriba del torno? Horrible y poco amor a la maquina.
Понравился леркодержатель.а остальное не очень,ничего нового.можно упростить.кстати ,поршень зажимает,и гильза установлена не очень правильно.низ гильзы не отценрован,только верх.
Это называется пое,,,ень по чехову.
Отрезать гГ образный отросток , проделать все и приварить обратно в разы быстрее имхо
Стенка за спиной ,,специалиста" очень близко.Случись что и убежать будет некуда .
You repost videos among others. It doesn't look good.
кто интересно этого умельца к станку подпускает
Хитрая наматывалка токаря
Загадка: Хреновина изогнутая до невозможности?
Ответ (коленвал)
Глушак от москвича😂
Поршень должен под своим весом падать!
точно нагреется и заклинит нафиг
А он без колец будет работать😂
Я один ждал когда это мастера на мотает на эту конструкцию???🤔
Он даже не знает какой стороной поршень вставляется
Шпиндельный подшипник не очень рад таким действиям
Now seriously, that drill is wobbling horribly, just putting and end mill in the drill chuck until you had a flat, then use a center drill and you could have had the hoe on center and not have had to clean up all the weld.
КАК ОН НЕ БОИТСЯ, ЧТО ПРИГОРЕТЬ МОГУТ ПОДШИПНИКИ У СТАНКА при электродно дуговой сварки.
How horrid, all that welding spatter all over the machine! As a machinist I want to make you sweep chips for the rest of the day and think about what you've done!
See that mill over there, the one noone else is allowed to touch, its 25 years old been run 16 hrs a day and it doesnt have a single mark in the table or ways!!! GO SWEEP!!!
I will buy all Blades in my hand😅😅😅. piupiu teafy to traning😅😅😅
Hahaha!
This is called Thinking out of the Box.
Again a Lathe is called the Mother of All machines, because a Skilled operator can do multiple things with a Lathe.
Thanks.
Local ground clamp or sent thru the lathe? Easy fry method
I hope it's grounded on the part. Poor bearings if not.
I think best buy instan Blades😂😂😂ready to use😂😂😂
How's the bearings in the lathe after all that welding ?
Если клиент доволен то почему бы и нет. Пакистанские технологии.
Для токаря 1 разряда пойдет, только остальным не подглядывать.
Esse sim pode dizer sou profissional da area
Este trabajo lo hacía hace muchos años atrás, ahora me dedico a otra profesión 🦾🕺
Массу на деталь ...
Браво!!! Кое-что и я б сделал в своём гараже,но додуматься вряд-ли смог бы.
Ну и название. Перевод что-ли такой?
And that, my friends, is one of the best ways to destroy the bearings in your lathe, if that’s what you’re after!
Такой работник долго не проживет …….
Мне кажется что при таком варианте обработки лучше было приварить станину к патрону)
Parece uma suspensão dianteira de vespa.
Can you believe this? You have that much skill that can for example make a bolt and screw the size you like with material you like instead of going to Home Depot trying to find it. What a level of freedom in life. Thank you for showing this dream to even be possible.
Friend of my parents makes scale steam locomotives from scratch on his lathe. He even machined a screw that had fallen out of my mom's glasses. Crazy indeed
Биение не вооружённым взглядом видно
Наверняка засрал искрами станок
❤❤❤❤❤
Amazing
крура .
Good and butifull idea❤
🇹🇹🇹🇹🙏🙏❤❤
Muy bueno
Good idea
حرفي ماهر 👍
Un mare pericol astea se faceau în evul mediu
Excelente trabalho
При фрезеровании подачу делают навстречу вращения фрезы. При попутной подаче фрезу закусит.
No hay fresado...
😂😂😂😂
É SHOW !