For .25 Hybrids out of the Superior Liner I run my Reg @ 150 BAR...after polishing the liner I run about 50-100 MkII pellets through it to season it in before I start with Hybrids & that'll take 10-20 of them to get the liner to settle down. Pull your barrel & probe...insert the probe into the barrel so it lines up with the transfer port...mark the edge of the probe against the barrel while inserted with a fine point Sharpie...reassemble and adjust the thread on the cocking rod/probe block as needed to line up when closed. Barrel set screw torqued to 20 inch pounds. Muzzle nut torqued to 25 inch pounds. Best velocity was 950-1030 fps but still shot good at lower speeds. You should be getting MOA out of her 👍
I've never bothered tracking barrel nut torque, thats a great idea. Its always been measured in my guns as "not too tight" or "try not to break it you moron" haha the liner is fairly well seasoned already but im keen to start over
Nice video..lil tip.. for those stiff parallax wheels. I found if I apply a dab of oil to the parallax and use a heatgun to spread the oil it softens the oring inside and loosens the stiffness. NO MORE SORE FINGERS
Hey, Meaty...nice to see some pre-Typhoon goodies...better get your rubber ducky and swim ring ready but it will have to be a BIG one since you are up on a mountain:-) Cheers and good luck!
Couldn’t help but notice the Burris scope box on the table. I put a 3X Burris pistol scope on my Diana Bandit PCP multi shot.22 cal pistol and what a game changer. It can take squirrels, tweeties, what ever out to 50 yards and head shots all day long at 30 yards. 685 FPS with 15.89 Hades. If you don’t have this 180$ pistol boss...your missing out on some fun. It makes a great truck gun also. I picked this AOA adjustable scope up used at a local gun shop for 75$. Yeah I know what it cost new...what a deal right? Great optics and a forever warranty ain’t bad either. Think your Cane Toads might really be scared if you had a Bandit .22. Would love to see that video. Thanks and BTW dig your fashion sense...Ha Ha...whatever works right? God bless.
Great video good stuff kandL nice but yes the polishing does work i polished everything in my impact even the washers in the reg. And the slug kit with pin probe i polished as well valve rod even a lil bit on the liner heavy superior helps i guess good stuff buddy thanks for sharing bsafe keep them coming 👍 😀
How about making a cast concrete bench rest top? You could even seed the logo of the channel with broken glass into the concrete top while its curing, then trowel it in, kind of like exposed aggregate without sharp bits. 💡💡🇦🇺
Enjoyed the video mate. Wish I had some of your knowledge on the FX Impact. They are so expensive here in Aust. Add shipping cost to far away Perth also. Can’t believe the rain you guys get up there. Looking forward to the next Video. Cheers
Great vid.. not one buuuuuurrrrp, odd. Try a Caldwell stable table, they are rock solid. The table surface is a little slick but that can be fixed or replaced. I lol'd when you talked about the rabbit hole of tweaks to improve your groups. I have been there, it never ends. The gun evolves from a modular multicaliber high mag capacity plinker/pest gun to a single shot don't touch it or even look at it funny because the settings are "perfect" bench gun.
I bought it because you can do all that stuff, I like that you can make it do stuff rather then just have to settle for what it gives you out of the box
Also don't feel bad about the fx hybrid slugs I've tried everything to get them to group good out to 100 yards and I always get flyers ill get 3 or 4 in. The same hole then a flyer off to the side lol I've shot them at 1025 fps to 780fps and I always get a flyer lol but I still like them maybe I'm just a bad shot anyways thanks for sharing bsafe
I don't really know what "ring of trust" means but im an element optics pro staff member if thats what your asking. im not selling the S&B, just trying new things.
Love all the goodies shame they dont make the extending butt for the crown( there's a lovely adjustable one ) as I'm a big bugger . One thought on the stiffness of the paralax (i assume u meant side wheel one) its possibly you may have overtightened the mounts , I had the exact same on an Optisan took days to work it out and was too late by then, thankfully they replaced it. Think the element only takes max of 17inlb.
@@meatheadmarksman2013 good job they have a no quibble warranty. The one really nice bit of kit i have for working on the guns is the torque screwdriver as thats the only thing you can really F**k up badly (prior lessons learned)
Hello, nice video as usual. Just to say something about the paralax issue you talked about. I had the exact same issue, but thanks to Matt, I solved it. Either you put the front mount further to the front, wich it seems you can not do by looking at the video, or you just simply DO NOT tighten the front mount so much. Problem solved with me ! Cheers. 👍
Great video bud . Is the safety still on the same side of the gun ? I want mine moved to other side so I can use my thumb (like the M-16A1 and A-2 ) . I hate having to move my thumb from one side to other to use safty . I might have to make one for myself . If you don't like what you have ....make what you want .
Have you played with different lubes on your pellets? Great video, I'm looking forward to install the corrected safety that's not in the way 🙂. Funny how they have lived with that for all this time lol
Maybe the parallax adjustment knob need a wheel? 60-80-100mm may do the trick. Could go full out and put one of those great big 6” on it..Ha Ha...no just kidding. I use an 80mm on mine. Not too much really and only like 20-30$.
Giddy mate your video are great AUSTRALIAN MADE 👍 , also just wondering what do you use for fill your pcp , I noticed there was one called air king compressor from the people that support you , have you done a video on them thanks denis
I use a modified yong heng compressor. the air king one looks good but I havnt had a crack at using one so cant really say. I love my yong heng compressor tho
@@deanmorriss7184 my impact worked fine without all the mods too just like the bsa, Bendigo, streamline, crown etc etc. They are "nice to haves" not really "need to haves"
@@meatheadmarksman2013 I think you'll need to issue your sheep, horses and llamas? with body armour! I feel sorry for the animals who can't get under a tree, etc with hail that big
I have to write this........WTF is going on with you Hodge??? that is not the dude I know....is it some kind of split personality going on??? Jekyll and Hyde thingy? Dressing up in FruFru flavors, no barbing, being kind of politically correct? at least tell me that you were wearing your crocs or flipflops!! Anyhow....thanks for sharing your new accessories/gadgets with us. Liked the buttstock, but like with the saber one, great, awesome, subline quality, but a bit to spicy price tag! Will have a look for each of them on the Black Friday séance and see if I invest in one of them. PS!!! are you still alive and kicking after the storm? 👀
Were all good, only got a little hail. Down south was pretty bad, loads of hail damage. I had no idea I was being politically correct lol I guess there's a first time for everything haha
![[TH] VALORANT Champions Seoul - Grand Final - EDG vs TH](http://i.ytimg.com/vi/WvObMc9VelI/mqdefault.jpg)
Great video, good luck with the storm ⛈
Nice precision toys for grown ups cheers from Canada
For .25 Hybrids out of the Superior Liner I run my Reg @ 150 BAR...after polishing the liner I run about 50-100 MkII pellets through it to season it in before I start with Hybrids & that'll take 10-20 of them to get the liner to settle down. Pull your barrel & probe...insert the probe into the barrel so it lines up with the transfer port...mark the edge of the probe against the barrel while inserted with a fine point Sharpie...reassemble and adjust the thread on the cocking rod/probe block as needed to line up when closed. Barrel set screw torqued to 20 inch pounds. Muzzle nut torqued to 25 inch pounds. Best velocity was 950-1030 fps but still shot good at lower speeds. You should be getting MOA out of her 👍
I've never bothered tracking barrel nut torque, thats a great idea. Its always been measured in my guns as "not too tight" or "try not to break it you moron" haha the liner is fairly well seasoned already but im keen to start over
Nice to get helpful tips from the inventor/designer of the ammo. The hybrids are a big step forward in lightweight high BC ammo, ty Rat sniper.
Nice video..lil tip.. for those stiff parallax wheels. I found if I apply a dab of oil to the parallax and use a heatgun to spread the oil it softens the oring inside and loosens the stiffness. NO MORE SORE FINGERS
Hey, Meaty...nice to see some pre-Typhoon goodies...better get your rubber ducky and swim ring ready but it will have to be a BIG one since you are up on a mountain:-) Cheers and good luck!
Always good, very informative.
Couldn’t help but notice the Burris scope box on the table. I put a 3X Burris pistol scope on my Diana Bandit PCP multi shot.22 cal pistol and what a game changer. It can take squirrels, tweeties, what ever out to 50 yards and head shots all day long at 30 yards. 685 FPS with 15.89 Hades. If you don’t have this 180$ pistol boss...your missing out on some fun. It makes a great truck gun also. I picked this AOA adjustable scope up used at a local gun shop for 75$. Yeah I know what it cost new...what a deal right? Great optics and a forever warranty ain’t bad either. Think your Cane Toads might really be scared if you had a Bandit .22. Would love to see that video. Thanks and BTW dig your fashion sense...Ha Ha...whatever works right? God bless.
Great video good stuff kandL nice but yes the polishing does work i polished everything in my impact even the washers in the reg. And the slug kit with pin probe i polished as well valve rod even a lil bit on the liner heavy superior helps i guess good stuff buddy thanks for sharing bsafe keep them coming 👍 😀
Great video as usual. Shoutout from Trinidad and Tobago 🇹🇹
K&L inverted safety is brilliant.
The original used to dig into my finger and I'd accidentally move it , the K&L solved it all.
cheers mate nice video
How about making a cast concrete bench rest top? You could even seed the logo of the channel with broken glass into the concrete top while its curing, then trowel it in, kind of like exposed aggregate without sharp bits. 💡💡🇦🇺
Enjoyed the video mate. Wish I had some of your knowledge on the FX Impact. They are so expensive here in Aust. Add shipping cost to far away Perth also. Can’t believe the rain you guys get up there. Looking forward to the next Video. Cheers
I miss Perth. Beautiful city and great people. WA rocks
In that outfit you looked like Ned Kelly on Holiday
Absolutely correct I love the helix and my parlex is stiff in areas and softer in others areas
Some folks suggested backing off the front mouinting screws, I did and now my side wheel is creamy smooth. My torque wrench must be out of whack
Great vid.. not one buuuuuurrrrp, odd. Try a Caldwell stable table, they are rock solid. The table surface is a little slick but that can be fixed or replaced. I lol'd when you talked about the rabbit hole of tweaks to improve your groups. I have been there, it never ends. The gun evolves from a modular multicaliber high mag capacity plinker/pest gun to a single shot don't touch it or even look at it funny because the settings are "perfect" bench gun.
I bought it because you can do all that stuff, I like that you can make it do stuff rather then just have to settle for what it gives you out of the box
Ah I give you Elemental Burrrrp for this video. Nice scope.
If the parallax is a bit firm in some parts, the scope mount screws might be too tight. Had that same issue.
yup, backed off the front mounting screws and its creamy smooth now
Gold would be perfect MH
Nice bottle clamp....LOL
Also don't feel bad about the fx hybrid slugs I've tried everything to get them to group good out to 100 yards and I always get flyers ill get 3 or 4 in. The same hole then a flyer off to the side lol I've shot them at 1025 fps to 780fps and I always get a flyer lol but I still like them maybe I'm just a bad shot anyways thanks for sharing bsafe
meat!! the schmtt n bender?? on the rak!! you are in the FX ring of trust !?
I don't really know what "ring of trust" means but im an element optics pro staff member if thats what your asking. im not selling the S&B, just trying new things.
STANKY Bro!!! TIGHT! 👍
Love all the goodies shame they dont make the extending butt for the crown( there's a lovely adjustable one ) as I'm a big bugger . One thought on the stiffness of the paralax (i assume u meant side wheel one) its possibly you may have overtightened the mounts , I had the exact same on an Optisan took days to work it out and was too late by then, thankfully they replaced it. Think the element only takes max of 17inlb.
yes i think that may be the issue, i set min to 16 but my torque wrench could be cactus
@@meatheadmarksman2013 good job they have a no quibble warranty. The one really nice bit of kit i have for working on the guns is the torque screwdriver as thats the only thing you can really F**k up badly (prior lessons learned)
Hodge go for the double plenum great video 👍
Well unfortunately I’m not on Instaslam but I’m using gold hardware on my juiced up MKI wink wink
Great video! I do have one question, on the cheek riser how many screws where you able to screw down?
Hello, nice video as usual. Just to say something about the paralax issue you talked about.
I had the exact same issue, but thanks to Matt, I solved it. Either you put the front mount further to the front, wich it seems you can not do by looking at the video, or you just simply DO NOT tighten the front mount so much. Problem solved with me !
Cheers. 👍
So are they seitefas or sǝıʇǝɟɐs, then?
Great video bud . Is the safety still on the same side of the gun ? I want mine moved to other side so I can use my thumb (like the M-16A1 and A-2 ) . I hate having to move my thumb from one side to other to use safty . I might have to make one for myself . If you don't like what you have ....make what you want .
Have you played with different lubes on your pellets? Great video, I'm looking forward to install the corrected safety that's not in the way 🙂. Funny how they have lived with that for all this time lol
i usually dont prepare my pellets or slugs at all but will probably start soon
Nice parts buddy. Any you aren’t using you can send to me 😂. Sounds like you have quite a bit to do to the impact to get it just right. Keep safe
Maybe the parallax adjustment knob need a wheel? 60-80-100mm may do the trick. Could go full out and put one of those great big 6” on it..Ha Ha...no just kidding. I use an 80mm on mine. Not too much really and only like 20-30$.
Nah it was the front scope ring on too tight. I think its time to buy a new torque wrench, my old one must be cooked
WTF.........that's one hellva lamp shade yer wearing.....don't stand next to a power socket or someone might plug you in 😂😂😂😂
I’d love the gold color inverted safety...don’t know how to dm you
instagram
Yo was just wondering what would happen If you were to ad the fx plenum what would that do
Right on buddy. Is it Kraford and Lift or Lip-T ??
Krawfish and lisp
@@meatheadmarksman2013 ya ya that’s it. Krawfish with a Lisp
Giddy mate your video are great AUSTRALIAN MADE 👍 , also just wondering what do you use for fill your pcp , I noticed there was one called air king compressor from the people that support you , have you done a video on them thanks denis
I use a modified yong heng compressor. the air king one looks good but I havnt had a crack at using one so cant really say. I love my yong heng compressor tho
@@meatheadmarksman2013 thanks for your reply
Gday . Great new add ons but makes the Impact a hell of a lot more expensive.maybe FX should put this stuff on them from the factory. Cheers Dean
is there even one single gun on the market that comes with all that? if there is i havnt seen it....
@@meatheadmarksman2013 Gday you might not have seen it . Didn’t have to add anything to The MRod or the BSA Ultra or the Streamline.
@@deanmorriss7184 my impact worked fine without all the mods too just like the bsa, Bendigo, streamline, crown etc etc. They are "nice to haves" not really "need to haves"
Was that cricket ball sized hail make a mess at your place? I see it punched holes in tile roofs up in Brisbane
not hail at my place yet but could happen at any moment
@@meatheadmarksman2013 I think you'll need to issue your sheep, horses and llamas? with body armour! I feel sorry for the animals who can't get under a tree, etc with hail that big
Can you use the saber tactical cheek riser instead and make it work
saber tactical one works fine with single shot loader
@@meatheadmarksman2013 can you use it with the k&l butt stock.
Someone else was saying that you could not use the saber tactical cheek rise with the k&l buttstock
@@tomiliff7591 oh rite, yeah not sure havnt tried it.
You still breathing or have you succumbed to the storm?
We did okay. Small hail, few trees down. Nothing like what happened down south
I have to write this........WTF is going on with you Hodge??? that is not the dude I know....is it some kind of split personality going on??? Jekyll and Hyde thingy? Dressing up in FruFru flavors, no barbing, being kind of politically correct? at least tell me that you were wearing your crocs or flipflops!! Anyhow....thanks for sharing your new accessories/gadgets with us. Liked the buttstock, but like with the saber one, great, awesome, subline quality, but a bit to spicy price tag! Will have a look for each of them on the Black Friday séance and see if I invest in one of them.
PS!!! are you still alive and kicking after the storm? 👀
Were all good, only got a little hail. Down south was pretty bad, loads of hail damage. I had no idea I was being politically correct lol I guess there's a first time for everything haha
Nice hat - did your Granny give you that?
shes a stylish wizard
@@meatheadmarksman2013 That she is .... Stay safe in QLD mate... regards from England
Who made the hat for ya? I’d like one made from beer towels 👌😎
www.avenelhats.com/floppy-flat-top-towelling-hat/
They used to be everywhere in Oz many decades ago
A tanktop does not make you a meathead....you need actual muscles