That product needs to be shaken for ages to mix it properly. I had that same lack of results at first, but then I noticed how much thicker the goop was at the bottom. I’m probably not the first to say it though, but those sanders are less than $75 per day to rent.
i bought a jug of this product and my first problem was reading the miniature instructions.i then went to u tube and i,m taking it back.u tube is very informative.great video by the way.
I did it myself with a drum sander, went against the grain then smooth marks out with the grain. Took a few hours 2-3hours. The edges plan on using some chemical remover
We tried the stripping solution and it did not work either. We have all of the deck flooring replaced and we bought need spindles to replace ourself. He is sanding the area that does not come off. He is so sick of sanding, I think has at least 30 plus hours in so far and we hopefully can complete it this weekend. Good luck.
*You can rent that floor sander from home depot for $62 a day and with that sander you can finish sanding your whole deck in 1 day, then just wash and apply your new semi transparent stain.*
You made me laugh!! I enjoyed your video! I thought it would be easy, power wash and apply more deck over paint. OH NO! It is peeling everywhere! I found bad areas. I am on day one and I have already reached out to a somebody to do it for me!
I learned the best way to remove the stripper is with a very high powered pressure washer but it does require a few applications depending on how heavy the stain is. Only required light sanding when done
I used Jomax striper and power washer. I sprayed it on and waited 15min and power washed it. No scrubbing needed. DID NOT TRY ON A SOLID STAIN. I used clear stains for 15 years and then I used a semi transparent before I completely removed the stains with the jomax.
BTW, when I spoke to the people at HomeDepot they told me that there is no chemical that would remove deck over and not to waste my time and effort on this. I also spoke to Behr and they confirmed that chemicals will NOT work. I have been working on my deck for two weeks now and it has been a scaping and sanding process. It has been hard work but finally using a scraper, angle grinder and 36 grit sandpaper I am able to see good progress. I will seal and stain the deck afterwards but will NOT use any Behr products now or in the future. If I knew now when I first installed the deck it would have been composite and I could be sitting with a beer enjoying the deck right now
That was really hysterical, you made me laugh so much thank you. luckily i have a little deck but its not any less painful getting the stuff off it - maybe my check won't be as large as yours lol
Hello sir: I have used the Behr product for many years as Its only $18/gallon at any Home Depot compared to other products costing $48. Fast results after 20 minutes. I sincerely hope that your results were in jest as I could have your entire deck stripped in 6 hours instead of weeks using BEHR saving you $1300. I noticed that you didn't put the cap back on the jug expecting you to trip over it causing the disaster. Keep On STRIPPING !!!!!!!!!!! Bro
So when you paid someone, did they not have success with the sander? Did they switch to the diamabrush? I got most of mine off with a scraper but I have probably 5 boards (12 feet long) left to do that it’s REALLY stuck on there. To rent the sander it’s 50$+13$ per sand sheet, or I can try and find a diamabrush here in Ontario somewhere unless the drum sander can do that much.
Dude, you’re hilarious. Great video, loved the spongebob meme cuts - you’ve clearly watched a lot of TH-cam with those great kids! Behr “Transparent” Weatherproofing Oil “Clear” Penetrating Oil - does anybody know how to remove this crap from my brand new Select Pine pressure treated deck boards? I put the quotations there because it ain’t transparent nor clear!!! Can I use a degreaser? Somebody halp meeeee please…
That product needs to be shaken for ages to mix it properly. I had that same lack of results at first, but then I noticed how much thicker the goop was at the bottom. I’m probably not the first to say it though, but those sanders are less than $75 per day to rent.
Yes, true! "Stick to what you know"; I have the same problem now.
i bought a jug of this product and my first problem was reading the miniature instructions.i then went to u tube and i,m taking it back.u tube is very informative.great video by the way.
This is the best deck diy video out there!
Wagner paint eater would have finished that in 1 day. Random orbital with 40grit 50 pack diablo discs.
Glad I found you! Watched all the same videos. I've been toying with the idea of doing it myself. WTF was I thinking 🤣🤣
I did it myself with a drum sander, went against the grain then smooth marks out with the grain. Took a few hours 2-3hours. The edges plan on using some chemical remover
Omg thank you for this!! I have two decks to remove behr deck over paint from and am feeling the same way!! Lol Your kids cracked me up!!
LOL! I love it. I think I may have to source someone to do mine, Just looking at the job i need to do gives me chills. Nice video brother.
We tried the stripping solution and it did not work either. We have all of the deck flooring replaced and we bought need spindles to replace ourself. He is sanding the area that does not come off.
He is so sick of sanding, I think has at least 30 plus hours in so far and we hopefully can complete it this weekend. Good luck.
*You can rent that floor sander from home depot for $62 a day and with that sander you can finish sanding your whole deck in 1 day, then just wash and apply your new semi transparent stain.*
So do I use just need the sander or do I use paint remover and pressure washer first?
You made me laugh!! I enjoyed your video! I thought it would be easy, power wash and apply more deck over paint. OH NO! It is peeling everywhere! I found bad areas. I am on day one and I have already reached out to a somebody to do it for me!
I learned the best way to remove the stripper is with a very high powered pressure washer but it does require a few applications depending on how heavy the stain is. Only required light sanding when done
I'm in the same boat right now.
I used Jomax striper and power washer. I sprayed it on and waited 15min and power washed it. No scrubbing needed. DID NOT TRY ON A SOLID STAIN. I used clear stains for 15 years and then I used a semi transparent before I completely removed the stains with the jomax.
Tom did that work well?
@@SkardyJr Yes
@@toddsmith1617 will that also remove a solid stain?
@@MrSpandya22 It won't remove DeckOver with the grit texture if that's what you are asking. Nothing will.
Oh my gosh thank you!
Boiling hot water.... it works! I made the mistake of putting this horrible stuff on my deck. Pour hot boiling water on it and it peels right off.
I am going to give that a try. I will never buy another behr product
Too funny! I have smaller deck. Hopefully I won’t need to whip out the check book! The kids did well.
- Haha... what a great reality video! Goes to show that it's never as easy as it seems it would be...
BTW, when I spoke to the people at HomeDepot they told me that there is no chemical that would remove deck over and not to waste my time and effort on this. I also spoke to Behr and they confirmed that chemicals will NOT work. I have been working on my deck for two weeks now and it has been a scaping and sanding process. It has been hard work but finally using a scraper, angle grinder and 36 grit sandpaper I am able to see good progress. I will seal and stain the deck afterwards but will NOT use any Behr products now or in the future. If I knew now when I first installed the deck it would have been composite and I could be sitting with a beer enjoying the deck right now
Glad to see this. I have old DEck Over on mine, of course, it has failed miserably. I was thinking of chemicals, but youve confirmed that it wont work
low key you are funny my man, i am having the same experience with my deck
good job, funny, cute kids
Stick to what you know!
That was really hysterical, you made me laugh so much thank you. luckily i have a little deck but its not any less painful getting the stuff off it - maybe my check won't be as large as yours lol
Hello sir: I have used the Behr product for many years as Its only $18/gallon at any Home Depot compared to other products costing $48. Fast results after 20 minutes. I sincerely hope that your results were in jest as I could have your entire deck stripped in 6 hours instead of weeks using BEHR saving you $1300. I noticed that you didn't put the cap back on the jug expecting you to trip over it causing the disaster. Keep On STRIPPING !!!!!!!!!!! Bro
So when you paid someone, did they not have success with the sander? Did they switch to the diamabrush?
I got most of mine off with a scraper but I have probably 5 boards (12 feet long) left to do that it’s REALLY stuck on there. To rent the sander it’s 50$+13$ per sand sheet, or I can try and find a diamabrush here in Ontario somewhere unless the drum sander can do that much.
The diamabrush did a much better and faster job. They did mot have success with the sander.
Any idea where I can get diamabrush, I’m in southern Ontario canada if it helps. Or did they supply it
Lowe’s or Home Depot
you could also check it out on Amazon. They run around $49
The cheapest I can find it is 181$ canadian.
Go to diamabrush.com/store-locator/
I am just going to pull up all wood, put Trex and be done with it. Not going to go through all this work anymore.
I had the same bad experience with this Behr stain stripper
thanks for making me laugh
Too cute 😆
Dude, you’re hilarious. Great video, loved the spongebob meme cuts - you’ve clearly watched a lot of TH-cam with those great kids! Behr “Transparent” Weatherproofing Oil “Clear” Penetrating Oil - does anybody know how to remove this crap from my brand new Select Pine pressure treated deck boards? I put the quotations there because it ain’t transparent nor clear!!! Can I use a degreaser? Somebody halp meeeee please…
Hahahaha! Never knew deck stripping could be so entertaining!
That product sucks
Was that $1600 just for stripping, or was that for restaining also?
That was hilarious
Don't be a schmo hire a pro
LOL