ฝัง
- เผยแพร่เมื่อ 30 ก.ย. 2024
- Hydrographics is the application of a pattern piece of art (film) onto an object in order to customize it, or change its character. Unless you are paying a premium, the “wood” or “carbon fiber” in your car is created by this process as is the camouflaged guns and ATVs you see out in the wild. This application method is decades old, and requires 5 basic ingredients: paint, hydrographic film, water, activator, and a protective clear coat.
In summary the part is first painted, (most hydrographic film is semi-transparent, and the base coat influences the overall finished look). The film is then floated on the surface of warm water for a minute or two in order to soften the PVA backing. The upper-facing surface of the film is then sprayed with a hydrographic activator, which turns the film into a liquid. The painted part is then slowly lowered into the film, and the paint chemically bonds to the liquid film, leaving the part “painted” in the design of the film.
Once “dipped”, the part is the gently rinsed in water to remove any excess PVA, and allowed to dry on a rack. Once fully dry, the part is then clear coated for UV and general wear and tear protection, but also to give an array of gloss levels, from wet-look gloss down to a matte clear.
Get all the supplies you need to turn your garage into a fully functional dip shop @ www.ohwpaint.com
![ผัวเถื่อน - ยูริ โตเกียวมิวสิค [ OFFICIAL MUSIC VIDEO ]](http://i.ytimg.com/vi/P08ORRVDGl8/mqdefault.jpg)
I’m gonna dip my car in my neighbors pool with a crane and hydro dip my whole car 😂
This is something Mr beast would do lmao
Best howto I've seen for this . No bullshit and strait to the point , good results too..awesome thx
Thanks Adam!
This is still true 2 years later.
thx, Great video
but the music is stressing !!
We can't disagree with you there. Royalty free music...lol
@@OHWPaint haha been there, i finally customized my N3ds on my channel, thx again
How do you dispose of both used waters? Can I put down my drain or backyard? and if so will it make the grass or sink the dip pattern?
hydrodipped grass sounds pretty cool ngl
put it the neighbours drain
Hello! I have the same question of some other comments... How often should I change the water and how can I dispose of the non-usable water?
Hi, how much time should i wait between final base coat and dipping?
You want to wait 5-10 minutes until the paint is dry to the touch
He doesn't seem to be a good conversationalist
i bought a hydro dip starter pack with some white primer .. do i have to base coat it after ? because even primer layer dried up it start to get liquid again .. and messes up the whole dip .. do you know whats going on ?
Who’s paint is it?
@@OHWPaint its from mtn i bought like a hydrodip starter it .. but basicly without instructions haha just the tools
Do I need to paint the shell if my controller is white already and I want it white under the hydro film?
Hi Josh - great question. You will need to paint the controller as the film needs to "stick" to the paint and will not adhere direct to the substrate. Hope that helps!
पायरी ४: चित्रपट सक्रिय करणे
ॲक्टिव्हेटर चांगले शेक करू शकते, नंतर अंदाजे लागू करा. पृष्ठभागापासून १२"
चित्रपट काचेचा दिसला पाहिजे
चित्रपट पूर्णपणे सक्रिय होण्यासाठी १०-२० सेकंद प्रतीक्षा करा
Why did you spray something onto it before doing anything else, is that paint, dose it make it stick better? Dose it make it last longer? Dose it make it feel better?
That's an activator spray.
@@magbago8006pretty sure they meant the primer. And it does all the hydro film to stick better
Nice Video Thank you
Shake can vigorously for 2 minutes, then apply a light coat? I followed the directions, I don't know how people do this and get it correct? I put on the lightest coat I have, even though I'm burning up hot, I don't know what this has to do with dipping my controller
Edit: to put the clear spray ihave to get out my medium coat? FML
Can you get custom designs printed on the dip pattern? Like, can I get a specific car or a wedding picture made into a pattern for hydro dipping? If so, where do I get that made?
Sorry, we do not do custom designs, and unfortunately, there is nobody we can recommend. This will be a Google situation for you sorry for the inconvenience!
2k clear coat used or 1k?
Why did you make look so easy? Whats the correct method for dipping at the 30* angle. As in, which part should be dipped in first for proper coverage
Hi there -- Send a picture of the item you are dipping to info@ohwpaint.com and we can better help.
What is this god awful music
I got question . If i open a shop ,
How often should i change the water?
Is it really necessary to paint the part before dipping ??
What paint to use on !!!
Glossy or matte !!!
And about raising, why does the water look like its a soapy water ...
Please answer all my questions please ...
Hi LWL - we recommend One Hit Wonder base paint (yes you need to paint the part so the film has something to adhere to). The gloss level depends on personal preference and is determined by the clear coat. The water is not soapy it is most likely the PVA from the film/activator reaction. You do can clean the water of film residue with a fishnet from an aquarium store. Hope that helps.
पायरी २: भाग रंगविणे
२ मिनिटे जोमाने शेक करा, नंतर हलका कोट लावा
भाग ५-१० मिनिटे कोरडे होऊ द्या
समान कव्हरेजसाठी अंतिम कोट लावा
स्पर्श करण्यासाठी कोरडे होईपर्यंत आणखी ५-१० मिनिटे द्या
दरम्यान...
Clearcoat brand suggestions. Paint wearing off after hours of play. I need a harder clear.
The paint or dip should not be wearing off with any 2K automotive clear (a standard clear is more decorative and is not intended for things that will be handled)- feel free to contact us at info@ohwpaint.com so we can better help troubleshoot with you.
पायरी १: भाग तयार करणे
भाग स्वच्छ करण्यासाठी सॉल्व्हेंट डीग्रेझर किंवा डिटर्जंट क्लिनर वापरा
भागातून कोणतीही घाण आणि तेल काढून टाका
स्कफ पॅड वापरून, भाग निस्तेज करण्यासाठी समान रीतीने स्कफ करा आणि फिनिश हलके स्क्रॅच करा
सर्व कोनाड्यांमध्ये प्रवेश करा!
टॅक कापड वापरून, स्कफिंग स्टेजमधून धूळ काढा
How can I re-do it with my controller if I messed up? One part of the controller didn't stich with the carbon fiber film
simply rinse and dry. If there are any "globs" of film, sand smooth with warm soapy water. then dry, and paint directly over. No need to strip the part. paint right over the film.
How much would you charge if I had you do that to my firearms Slide and Trigger?
Hi Ehsan, We sell paint and hydrographic supplies. We do not provide hydrodipping services. But if you email us your info we can see if we know anyone in your area who can help. info@ohwpaint.com
What color spray paint do you guys recommend to receive a real carbon fiber look?
We like Metallic Graphite with our classic Black and Clear Carbon Fiber film.
पायरी ६: क्लीअरकोट
२ मिनिटे स्वच्छ हलवा आणि मध्यम आवरण लावा
१० मिनिटे कोरडे होऊ द्या
अधिक ग्लॉससाठी तुम्ही आता जड कोट लावू शकता
१० मिनिटे कोरडे होऊ द्या
२ कोट पुरेसे असताना, आपण अधिक संरक्षणासाठी अधिक जोडू शकता
started my first dip it turned out good but the item itself feels slightly sticky after overnight dry, what are we doing wrong?
Hi, it sounds like you may not have rinsed the dip properly - sometimes this can take up to 5 minutes. Please contact JJ via text at 305-318-1468 it you still have issues
is clear coat a must? what if I want a mat finish?
Hi, yes you need clearcoat to protect the film. Otherwise the ink will get scratched. For matte, we do sell a standard matte clear and a 2K matte clear that you can apply directly over the dip once dried
Great Video! Have question, I know you sanded the part before painting. What grit do you sand with, afterwards when you painted the controller is there no need to sand the painted controller before dipping. Thanks in advance🙂
we usually use a light gray Scotch Pad (extra fine) for scuffing. This provides enough 'key' for paint. Correct, no need to scuff before dipping. OHW has a long dip 'window'
@@OHWPaint 😊 Thank you
Can I dip objects made out of modeling foam?
Can you please send a photo to info@ohwpaint.com
Would I need to remove the original paint before preparing the new one?
As long as the existing paint is in good condition and adhered to the part properly, you can just degrease, scuff, and paint OHW over the top
@@OHWPaint Much obliged!
How long do I have to wait to rinse and does it have to be cold or warm water
you can rinse immediately, and as long as it's not hotter than 100 degrees, and temp is fine. The closer to 80, the better/ faster
पायरी ५: डिप
तुमचा भाग उचला आणि हलक्या हाताने फिल्ममधून ३०° कोनात बुडवा
पूर्णपणे बुडणे
पाण्याखालील कोणतीही अतिरिक्त फिल्म हळूवारपणे झटकून टाका
कठीण भाग एक!!!
जादा पाणी झटकून टाका
पायरी ३: डिपसाठी सेट करा
तुमचा चित्रपट रोल आउट करा
बोटांनी ओलावा - चिकट बाजू खाली!
सर्व कडा टेप करा
अंदाजे परवानगी द्या. भागाभोवती ५०% अतिरिक्त चित्रपट
रेझर ब्लेडने कापून टाका
I have another question, so im trying to hydrodip my ps5 panels, what step should i do first?
You need to clean (we like the degreaser Prep All) and scuff with a gray scotch pad.
@@OHWPaint all good then what do i do next after i use those two items
@@Sheldric09 Please follow the video or find step by step directions here www.ohwpaint.com/blogs/news/how-to-apply-hydrographics
@@OHWPaint thank you i most definitely will
So we have renamed decals, a nice new twist, but still a decal. Thanks, n nice work.
How long does it last?
if you use our 2k clear, indefinitely. As long as any car finish, if taken care of. The kit comes with a 2K Clear option and you can also find our 2K Clear here:www.ohwpaint.com/collections/clear-coats/products/2k-clear-coat
For ps4 controllers, do i need to use sandpaper for them or what type of degreaser should i be using for it?
We like Prep All degreaser. You don't need sandpaper, just a light gray scotch pad. Hope that helps!
@@OHWPaint that truly did help alot i do appreciate you for that info so much, one more question, where can i buy the gray scotch paper from?
@@OHWPaint i meant pad lol
@@Sheldric09 an autobody supply shop or check amazon or walmart
@@OHWPaint thank you 💯💯💯
that’s 1 way how to make a short presses long 😅
Whats an activator can?
Going to call you Monday. Daniel gave me your number. I need to get setup for hydro dipping in my shop
Sounds good!