Would be great to see how you go about changing the carrier bearing, have a zetor 9540 withplay in carrier bearing so would be useful to see how u go Bout it on the cvt
Great attention to details , tractor fan here also , your not alone when it comes to projects ! Where do you get stud plating done ? What’s the costs .
I would paint the front axle and front tombstone to smarten up the front end but at the same time it wouldn’t be too difficult to touch up the visible part of the engine block where the grey has faded. That would make it look like a full respray if you painted around backend as well
I am also rebuilding this axle, but i don't know, if this pin which holds the upper arm seats in the bushing or not. I already took out the other bushing. Can you film the whole process of rebuilding.
I would keep the tractor as original as possible and only touch up areas that need touching. I wouldn't install a centralised greasing system as they can block, at least with the nipple you would know if it was blocked.
Would be great to see how you go about changing the carrier bearing, have a zetor 9540 withplay in carrier bearing so would be useful to see how u go Bout it on the cvt
![[UNCUT] เก็บ "สจ.โต้ง" เอี่ยวมาเฟีย รู้ตัวคนบงการ ก่อนสั่งลั่นไก I คนดังนั่งเคลียร์ I 13 ธ.ค.67](http://i.ytimg.com/vi/o-J_p62D40w/mqdefault.jpg)
Would be great to see how you go about changing the carrier bearing, have a zetor 9540 withplay in carrier bearing so would be useful to see how u go Bout it on the cvt
Great attention to details , tractor fan here also , your not alone when it comes to projects ! Where do you get stud plating done ? What’s the costs .
I would paint the front axle and front tombstone to smarten up the front end but at the same time it wouldn’t be too difficult to touch up the visible part of the engine block where the grey has faded. That would make it look like a full respray if you painted around backend as well
Great video. But seriously the heading of the video my heart sank. Can't wait to see the end result.
Great video I think you should paint the engine as well especially with all the work you4 putting into it
Spray the whole lot have her like a new pin lad . Your dream tractor make her like a new 1 . Especially if ya going to zinc everything
I am also rebuilding this axle, but i don't know, if this pin which holds the upper arm seats in the bushing or not. I already took out the other bushing. Can you film the whole process of rebuilding.
Can You make a Video of Your Steyr 650 now?
I can but I haven't done any work to it since
Good stuff
Surprising what you find when you start ripping… just not always good stuff 😩🤦♂ least you know what needs done 👌👍
Would a big air hammer have bet that out?
Not a hope
Great videos but sound can be dodgy at times. Do you use a clip on mic that you put on your shirt maybe?
Where can you get bolts replated i have bolts i need done myself
Galvotech in shannon
I would paint it if you can, she will be like brand new. Your lucky you can do your own work
Will be some job when finished😊
I would keep the tractor as original as possible and only touch up areas that need touching. I wouldn't install a centralised greasing system as they can block, at least with the nipple you would know if it was blocked.
Since you are at it i would paint the engine and the front axle instead of regretting it later :)
“Why didn’t you get one that the front doesn’t fall off” 😂😂
Well normally the front doesnt fall off 🤣
Once it all happened outside of the environment 😂
Them axles are a complete disaster especially when on a loader tractor wearing them out quicker with the weight
I like them ,good suspension
Spay all the tractor make like new and get 24 plates
🇮🇪🇮🇪👍👍🙏🙏
💞 Promo-SM
Would be great to see how you go about changing the carrier bearing, have a zetor 9540 withplay in carrier bearing so would be useful to see how u go Bout it on the cvt