REGARDING THE CONTROVERSY: The two sets of screws on a duplex receptacle weren’t put there as wire connectors; they are needed in case you want to split the two plugs on two different circuits. You can separate the two screws by removing the tab between them. However, code allows you to use them as wire connectors if you want. But it’s not required.
I was going to say it shouldn’t pass through and heat the receptacle up like you mentioned unless everything was on. Which would heat up regardless of the use of pigtails
This really made me happy bc I did it and it and got it to work for my grandpa I’m only 13 and I put in a new outlet in less then an hour he was happy and so was I
Just completed adding an outlet for my flatscreen behind the tv. Your video walked me right through it perfectly. I tested everything and it was perfect. Thank you
I’ll be doing the same now that I’ve watched this tutorial. I had the gist of how to do it, but this gentleman’s instructions cemented my understanding.
This was the easiest explaination ever. You can't mess anything up. Thank you so much for taking your time out to make this video. I just brought a house and they definitely skimmed on the outlets.
This is a perfect video. Very very simple. Didn't muddy it up with a bunch of nonsense. This probably covers 99% of what people need. Just subscribed. Thanks for the video!
Thank you for these very helpful videos! I had a pro electrician install two 20 amp home runs from the house to the shed and I was able to finish the job myself thanks to your videos!!! My plugs and lights are on one 20 amp circuit and the other 20 amp has one dedicated plug for a window air conditioner. Thanks again!!!
OMG! Thank you. Simple, but when you don't know, have many doubts, and you just want to get it done it's frustrating. Without vids like yours... I'd be sunk. Thanks!
Thank you for the tip. Grounding wire connectors were new to me. Thank you for the tip about using the tester. I do so all the time and, just yesterday, I was working on my dog porch. The panel was supposed to shut down 8 outlets, the outside light and the 4 LED ceiling lights. I found a 3 way switch was still hot. The breaker was mislabeled and the inside lights are powered from the adjacent room's lighting circuit. Also I was warned by my electrician to avoid quick connectors. He had a couple get hot and melt; he thought because the metal connection is so thin. If wires are twisted together, 3 three wires shouldn't overheat using a proper sized wire nut. Also, my house was built with the cheapest outlets, so I replaced them with Leviton's upgraded outlets. My other home center stopped stocking Leviton, but seemed to have similar. Those are both great, excepting the metal back plate is also a ground strip.. usually still better than the 39 cent variety. When the dog porch was completed, I had the contractor install the outlets. Somehow the hot wire rubbed against that metal back plate. I'm not sure why, but after a few years, when plugging something into that outlet, the hot would come into contact with ground, so always make sure all that extra wire is tucked away from the back of the outlet. In my case it was never enough spark to trip the GFI or breaker but, after 6 years, melted the insulation off the last 1 1/2 inches of the black wire.
Great video! Of course the trick is always how you get the wires bent and back in the box. I'd like to see you do that. That is the one thing that is always challenging for me.
Along- Starting with the ground wire, fold in into a "Z" so it does not catch or cross the white and black wires as you z-fold it flat. Repeat with the white wire, avoiding conflicts with the other two. Offset the wires to one side so they don't stack up on top of each other. Finish with the black (hot) wire. Using two-gang boxes all the time instead of single-gang boxes will give you a LOT more space inside the box and make this easier. (I learned this last trick the hard way w after wiring an entire garage.) :-(
Very good example. Some may try to daisy chain this when inexperienced, very good explanation. Myself personally I wire nut wires under a wire nut with their pigtail.
A perfect video! I watched it twice and was able to add a GFCI outlet under my kitchen sink! It was a bit of a pain cutting through the back of the cabinet, then drywall, and trying to strip wires with the disposal in the way while on my back, but it turned out perfectly. Next time I'll do a little more pre-planning! 😂 Thank you for sharing your expertise!
Great tutorial! Very informative and complete with clear explanations and demonstrations of the process from start to finish. I liked and appreciated that you didn't make it about yourself by trying to be cutesy or show your dog or significant other, etc. Friendly, concise, easy to understand, and at a good pace. Thanks!
OMG!!There, you said it finally here. YESSSSSS. It is the right way to wire it. Pigtail!!! Excellent work! Maybe an honest electrician with integrity have advised you to do it this way. Thank you
Very good video. Regarding the overheat/over current from fastening both hots to the gold screw. Because of the shunt between the gold screws/post electrically they are the same whether individually attached or using the wago. Personally I like the wago far above screwing down to the post. Thanks
After I checked everything and walked my way back and couldn’t find the problem I called my cousin (that I forgot was an electrician) and he told me to check all the bathroom and check the GFI, because I was connecting the new line from a bathroom line the GFI from the other bathroom that control all the bathrooms tripped, after that he showed me how to do it and it works now. I really appreciate all your replies and knowledge. Thank you thank you.
Hi friend your videos are truly awesome, I do renovation here in Ontario Canada 🇨🇦. And I been learning lots of your video. God bless my friend, gir show tge way we all understand. Take care Dad. 😊
Super helpful! I'm adding to my basement (exposed studs behind wall and garage (exposes studs). Your tip about the Wago connectors was especially helpful.
so quick question, everyone i know and everything i have ever been taught says it’s fine putting the two blacks on the receptacle and two white wires on both screws. if it will create heat on the receptacle then it makes since those connections your using will create heat there. either way you look at it. they both become a distribution center for lack of better terms.
Nothing wrong with using the screws. I’ve done it my whole life. But I made some early videos using that method and a lot of people commented that pigtailing was better. The other benefit, beside heat, is the outlet can be removed without disrupting the rest of the circuit. Of course, I always recommend turning off the circuit breaker first, but many electricians prefer to leave it on.
Quick question for ya. I purchased a Klein Tools RT250 GFCI Outlet Tester with LCD Display. It's saying "open ground." I used one of those green nuts with a hole at the end to twistthe two groundstogether. Did I mess something up, or should it be reading that way?
@y00o00u00t00u00b00e Test the incoming ground wire to see if you can voltage when tested against the hot. If no voltage, there is a break upstream. If it has voltage, tighten the connection with the outlet pigtail.
Thank you for your videos as they definitely help the husband at home complete some simple diy projects. I have what may be a stupid question.. i’ve always avoided doing electrical because it can be very unforgiving. But I’m learning a lot more and becoming a little more comfortable. I am adding a second outlet using an existing outlet. My question is, what type of wire do I use? As I went to a hardware store to pick some up I found out there are many many different kinds. So as I said, I am new to this, so bear with me lol. Thank you for all your help.
Find the circuit breaker for the existing outlet. The number on it (usually 15 or 20) is the amperage rating. If it’s 15, you can use 14/2 wire. If it’s 20, you need to use 12/2 wire.
well done.. most everyone will gain from this.. my case however,my uncle was great electrician.. trained by military.. owned his own company as electrical contractor... made a very good life after serving his country.. he always train his workers and me to always work with power on.. as he said,"more people get hurt from dead wires than from live... you kill power and if not in place where you can lock out tag out... somebody flips switch back on and POW.. youget zapped.. but if you leave power on you know to be more careful and not touch both wires at same time...he lived into his 90's..I'm in my 70's now and never had any zapps due to me thinking wires dead and someone flipped switch.. I always work with live wires BUT I am very careful and take extra time to go slow and safe..
It is safer and easier working with a dead circuit unless there is no choice which is very rarely the case in a residential situation. As far as the concern of someone else energizing the circuit, I put a pad lock on the entire breaker panel after the circuit is shut off. If this is not an option due to panel design or other reasons, a circuit lockout device should be used on the individual breaker. Always check at the point of work that all wires are de-energized as more than one circuit could be coming into the same junction box.
hi, your video was most helpful. I’ve put in many outlets before, but this particular case they want to add an outlet in the bathroom it has to be a GFI the only power I can get to on the other side of the wall there’s a kitchen outlet I guess the principal is the same, I guess I’m better off to also put a new GFI in the kitchen
Thanks for such a very well explained video sir, i need dummie proof videos when it comes to electrical and you've nailed it, thank you once again and keep it up!
I just did another one, this time it worked and then it didn’t. The breaker did not trip but I have no power on the outlet. There’s power coming from the breaker but it’s not going all the way to the outlet. Do you have any idea what happened?
@jrmsantana It’s impossible to say. You need to use a voltage meter and figure out where it was wired wrong. If you can’t figure it out, please call an electrician or qualified handyman.
Awesome video!!! This helps me a lot as I am going to finish a small room and just need a couple of outlets installed. Luckily the backside of both walls are exposed so easy peasy. Makes me feel confident now that I have to get it inspected. Well done!!
Clearly explained, Question, can I use this procedure when mounting a GFIC outlet on the exterior wall using the required waterproof box and enclosure? Thank you
Great content here! Love everything except the mention of wago lever nuts having a higher operating temp range. I believe it is actually the opposite - most wire nuts have a higher operating temperature than Wago lever nuts.
Great content here! Love everything except the mention of wago lever nuts having a higher operating temp range. I believe it is actually the opposite - most wire nuts have a higher operating temperature than Wago lever nuts. Always check the manufacturer’s specs
I have a light switch that turns my light off and a power outlet next to it. How would I fix this so the outlet remains on and the light turns off and on with the switch? Great content!!! This is my favorite new TH-cam channel.
This video definitely gives the information in a way that’s easy to understand, I’m going to add an outlet higher on the wall to mount a tv but the outlet I’m going to get power from his about 4.5 ft to the right and at the bottom of the wall. Anyway to run the Romex without going through the studs?
This is perfect, thanks for posting!! Quick question….. My existing outlet has line and load wires already. How do I tap isn’t the circuit? Use a junction box????!!!
Going to build a cargo trailer conversation to camper soon..and wanting to wire 120v shore power only for now..this is now something simple to do myself, thanks to you!
The load doesn’t change by adding outlets to a circuit. Load comes from the devices plugged in and turned on. Here’s how I monitor circuit loads: th-cam.com/video/wnhNvfKy2rI/w-d-xo.html
This is an excellent video, thank you. I do have one question. What if the original outlet has 2 hot wires and 2 neutral already wired in? How do I attach the 3rd wire from the outlet I want to install?
Very informative video. Just had a question. Could you have created a pigtail for the ground wire just like you did for the black and white wires using one of those connectors? Or was there a reason you didn't? Thank you very much for your time and expertise.
Great video!!!! Question--: I have 2 outlets connected to each other in my bathroom walls, but I WANT TO REMOVE ONE OUTLET.... How do I do it?, and how to change the wires that go to this outlet I want to remove???? THANKS
So helpful. Annnnnd since you helped me scrutinize the details, I must tell you that I noticed at 5:34 that you have the black wire wrapped around the brass screw COUNTERclockwise. I wouldn't have noticed if you hadn't made a big point of it earlier in the video. Proof of good teaching! ;-)
Many thanks for your videos. I have watched several. They are extremely helpful. Do you have a video for a GFCI Receptacle installation with other outlets in-line? Thanks, again.
Yes, thank you,, very helpful video. Been a carpenter all my life, but never messed with electrical. I had "pro's" upgrade house to breakers, a ran a few new circuits. But, had an after thought, and want to add another outlet up higher on the wall, for a wall mount tv. Still have one side of the drywall off, so much easier now, than later! My question is if it is ok/safe to add another outlet. I wish I could send a pic, ha!, but I believe this new "tv" outlet would be the 3rd outlet on this new circuit. PS: the pigtail thing went by a bit quick for me, but think I got it after watching it a few times, 😆 I hope I can find those little connectors. I ass-ume, it doesn't matter in what "order" the source/hot wire, and the out going (2nd) black wire go into the connector? And then the 3rd "pigtail" wire(s) goes to source outlet. Thanks again!
Technically, there is no limit to the number of outlets on a circuit. You’re only limited by the amperage capacity of the circuit. If you attempt to use too many devices at the same time, you could pop the breaker. The average 4K TV uses around 1 amp so that’s not going to be an issue for you.
I would only use the heater if it’s a 20-amp circuit. Check the number on the breaker. If it’s a 20-amp breaker, use 12/2 wire to the new outlet. If it’s a 15-amp breaker, consider running a new circuit if you intend to use the heater.
I've never seen the through-grounding wire nuts FS here in California and ALWAYS use pigtails. ALWAYS check your local building codes to make sure that the connectors and methods that you want to use are allowed....
Very helpful video! This should be good for a garage ready refrigerator, correct? I’m planning on adding another outlet for the fridge alone from one of the existing outlets in the garage. Thanks in advance!
Consider running a new circuit for the fridge because they use a lot of startup power and it could flicker your lights depending on whatever else is on the existing circuit. If it’s not an option, then sure you can extend an existing circuit.
Thanks for all the work you send my way. I get about 20-30% of my work as a state certified electrical contractor following behind "electricians", trunk slammers and DIY'rs who tried ONLY because someone like you on the internet gave them the confidence. Keep up the good work.
My project is a 220 volt In conduit the A/C is Hardwired outside in a junction box on the unit , I need to run a line through siding inside and install an outlet to plug the new A/C into - old circuit breaker is 20 amp new one calls for 15 amp breaker - biggest thing now is get the 35 year old Kenmore through the wall A/C out
Thanks for this video! I’m in this situation adding an outlet on the other side of our bathroom vanity. Any special steps for adding the second outlet from a GFCI outlet?
I’ll be doing a video specifically on this topic soon because it’s a common question. But this video will also help you: th-cam.com/video/dbmRETinw0A/w-d-xo.html
I’d put the office outlets on a separate circuit because computers, monitors and printers draw a healthy amount of current, especially if you have more than one workstation. Especially if you have walls open.
REGARDING THE CONTROVERSY: The two sets of screws on a duplex receptacle weren’t put there as wire connectors; they are needed in case you want to split the two plugs on two different circuits. You can separate the two screws by removing the tab between them.
However, code allows you to use them as wire connectors if you want. But it’s not required.
Fantastic
After get done connecting the pigtails will them fit inside the Box just wondering if it will be a space for them?
@basicnunchucksduarnerey53 I always recommend deep boxes.
I was going to say it shouldn’t pass through and heat the receptacle up like you mentioned unless everything was on. Which would heat up regardless of the use of pigtails
This really made me happy bc I did it and it and got it to work for my grandpa I’m only 13 and I put in a new outlet in less then an hour he was happy and so was I
Wow good job
Wow way to go!
Good job buckarooo
Now that's what I call build memories
Core memory unlocked! Good job dude!
Just completed adding an outlet for my flatscreen behind the tv.
Your video walked me right through it perfectly. I tested everything and it was perfect.
Thank you
Glad it was helpful 👍🏻
I’ll be doing the same now that I’ve watched this tutorial. I had the gist of how to do it, but this gentleman’s instructions cemented my understanding.
@Josam01 You got this 👍🏻
This was the easiest explaination ever. You can't mess anything up. Thank you so much for taking your time out to make this video. I just brought a house and they definitely skimmed on the outlets.
Glad it was helpful 👍🏻
This is a perfect video. Very very simple. Didn't muddy it up with a bunch of nonsense. This probably covers 99% of what people need. Just subscribed.
Thanks for the video!
Thanks for subscribing! Welcome to the family!
Throughly explained. Not too fast. Perfect for DIYers like myself with so many questions. Definitely following for more videos and tips! Thank you!
Thanks for subscribing! Welcome to the family!
Thank you for a straight to the point tutorial. You're a very good teacher/instructor. Greetings to you and your family.
Thanks so much 😊
Thank you for these very helpful videos! I had a pro electrician install two 20 amp home runs from the house to the shed and I was able to finish the job myself thanks to your videos!!! My plugs and lights are on one 20 amp circuit and the other 20 amp has one dedicated plug for a window air conditioner. Thanks again!!!
Glad it was helpful 👍🏻
I want to run 3 plugs, one switch and a light/fan to a single plug for off grid. Can a single plug handle that?
G ood question. @@carolenglish5846
OMG! Thank you. Simple, but when you don't know, have many doubts, and you just want to get it done it's frustrating. Without vids like yours... I'd be sunk. Thanks!
Glad it helped!
Hands down the easiest and cleanest explanation I've found!!
Thanks 😊
Chris, you are an exemplary instructor! Thank you! 😊
Thanks so much 😊 Glad it was helpful 👍🏻
Thank you for the tip. Grounding wire connectors were new to me. Thank you for the tip about using the tester. I do so all the time and, just yesterday, I was working on my dog porch. The panel was supposed to shut down 8 outlets, the outside light and the 4 LED ceiling lights. I found a 3 way switch was still hot. The breaker was mislabeled and the inside lights are powered from the adjacent room's lighting circuit. Also I was warned by my electrician to avoid quick connectors. He had a couple get hot and melt; he thought because the metal connection is so thin. If wires are twisted together, 3 three wires shouldn't overheat using a proper sized wire nut. Also, my house was built with the cheapest outlets, so I replaced them with Leviton's upgraded outlets. My other home center stopped stocking Leviton, but seemed to have similar. Those are both great, excepting the metal back plate is also a ground strip.. usually still better than the 39 cent variety. When the dog porch was completed, I had the contractor install the outlets. Somehow the hot wire rubbed against that metal back plate. I'm not sure why, but after a few years, when plugging something into that outlet, the hot would come into contact with ground, so always make sure all that extra wire is tucked away from the back of the outlet. In my case it was never enough spark to trip the GFI or breaker but, after 6 years, melted the insulation off the last 1 1/2 inches of the black wire.
Wow. Thanks for sharing.
Great video! Of course the trick is always how you get the wires bent and back in the box. I'd like to see you do that. That is the one thing that is always challenging for me.
I’ll put it on the list. Thanks.
Along- Starting with the ground wire, fold in into a "Z" so it does not catch or cross the white and black wires as you z-fold it flat. Repeat with the white wire, avoiding conflicts with the other two. Offset the wires to one side so they don't stack up on top of each other. Finish with the black (hot) wire. Using two-gang boxes all the time instead of single-gang boxes will give you a LOT more space inside the box and make this easier. (I learned this last trick the hard way w after wiring an entire garage.) :-(
Very good example. Some may try to daisy chain this when inexperienced, very good explanation. Myself personally I wire nut wires under a wire nut with their pigtail.
I use pigtails when needed. But I have no issue using the screws for two wires.
A perfect video! I watched it twice and was able to add a GFCI outlet under my kitchen sink! It was a bit of a pain cutting through the back of the cabinet, then drywall, and trying to strip wires with the disposal in the way while on my back, but it turned out perfectly. Next time I'll do a little more pre-planning! 😂 Thank you for sharing your expertise!
I HATE working under the sink! Good job!
Hey, I'm about to do this in my house actually. I need a socket for toe kick lights. What challenges did you face and what would you recommend?
Great tutorial! Very informative and complete with clear explanations and demonstrations of the process from start to finish. I liked and appreciated that you didn't make it about yourself by trying to be cutesy or show your dog or significant other, etc. Friendly, concise, easy to understand, and at a good pace. Thanks!
Glad it was helpful 👍🏻 Thanks so much 😊
This is the best presentation. Thank you!
Thanks 😊
OMG!!There, you said it finally here. YESSSSSS. It is the right way to wire it. Pigtail!!! Excellent work! Maybe an honest electrician with integrity have advised you to do it this way. Thank you
Thanks 😊
Very good video. Regarding the overheat/over current from fastening both hots to the gold screw. Because of the shunt between the gold screws/post electrically they are the same whether individually attached or using the wago. Personally I like the wago far above screwing down to the post. Thanks
Thanks for your input
Thanks Dad!!! ❤
My pleasure
Thanks for teaching us. Very well explained and good vibes. Thanks
My pleasure
After I checked everything and walked my way back and couldn’t find the problem I called my cousin (that I forgot was an electrician) and he told me to check all the bathroom and check the GFI, because I was connecting the new line from a bathroom line the GFI from the other bathroom that control all the bathrooms tripped, after that he showed me how to do it and it works now. I really appreciate all your replies and knowledge. Thank you thank you.
Thanks for letting me know.
You are the father I've never had. Thank you so much for the information and savings .......... Not all heroes wear capes .
Thanks so much 😊
Great explanation with real wires and real outlets. Very helpful.
Glad it was helpful!
I just added an outlet, switch and light in a closet thanks to your videos! Great stuff! THANK YOU!
Glad it was helpful 👍🏻
Hi friend your videos are truly awesome, I do renovation here in Ontario Canada 🇨🇦. And I been learning lots of your video. God bless my friend, gir show tge way we all understand. Take care Dad. 😊
Thanks 😊
Very clear and concise video.. thank you so much !
My pleasure
Dude thank you this was hands down the best explanation I’ve ever seen. Guess I’m gonna have to watch all of your other videos now, lol
Glad it was helpful 👍🏻
Black people like gold is how I remember it
Everyone likes gold.
Lmfao
Bruh 😂
Or Black Power + White Neutral = closed circuit
@@TopDawgSportsClips😂😂😂 right it be our own ppl lol
Super helpful! I'm adding to my basement (exposed studs behind wall and garage (exposes studs). Your tip about the Wago connectors was especially helpful.
Glad it was helpful 👍🏻
Exactly what I was looking for. Didn’t know how to handle the two grounding wires and the four cables. Brilliant
Glad it was helpful 👍🏻
Thank you. This is exactly the video I was looking for. I hope you upload more videos😢
Thanks 😊
so quick question, everyone i know and everything i have ever been taught says it’s fine putting the two blacks on the receptacle and two white wires on both screws. if it will create heat on the receptacle then it makes since those connections your using will create heat there. either way you look at it. they both become a distribution center for lack of better terms.
Nothing wrong with using the screws. I’ve done it my whole life.
But I made some early videos using that method and a lot of people commented that pigtailing was better. The other benefit, beside heat, is the outlet can be removed without disrupting the rest of the circuit. Of course, I always recommend turning off the circuit breaker first, but many electricians prefer to leave it on.
Thank you for your video! I was able to get some new outlets in our garage 👍😎
Glad it was helpful 👍🏻
Quick question for ya. I purchased a Klein Tools RT250 GFCI Outlet Tester with LCD Display. It's saying "open ground." I used one of those green nuts with a hole at the end to twistthe two groundstogether.
Did I mess something up, or should it be reading that way?
@y00o00u00t00u00b00e Test the incoming ground wire to see if you can voltage when tested against the hot. If no voltage, there is a break upstream. If it has voltage, tighten the connection with the outlet pigtail.
Thank you for your videos as they definitely help the husband at home complete some simple diy projects. I have what may be a stupid question.. i’ve always avoided doing electrical because it can be very unforgiving. But I’m learning a lot more and becoming a little more comfortable. I am adding a second outlet using an existing outlet. My question is, what type of wire do I use? As I went to a hardware store to pick some up I found out there are many many different kinds. So as I said, I am new to this, so bear with me lol. Thank you for all your help.
Find the circuit breaker for the existing outlet. The number on it (usually 15 or 20) is the amperage rating. If it’s 15, you can use 14/2 wire. If it’s 20, you need to use 12/2 wire.
Thank you
well done.. most everyone will gain from this.. my case however,my uncle was great electrician.. trained by military.. owned his own company as electrical contractor... made a very good life after serving his country.. he always train his workers and me to always work with power on.. as he said,"more people get hurt from dead wires than from live... you kill power and if not in place where you can lock out tag out... somebody flips switch back on and POW.. youget zapped.. but if you leave power on you know to be more careful and not touch both wires at same time...he lived into his 90's..I'm in my 70's now and never had any zapps due to me thinking wires dead and someone flipped switch.. I always work with live wires BUT I am very careful and take extra time to go slow and safe..
Really good story, but I’m sure you can imagine, I can’t recommend that method to newbies who don’t have mentors like your uncle to teach them.
It is safer and easier working with a dead circuit unless there is no choice which is very rarely the case in a residential situation. As far as the concern of someone else energizing the circuit, I put a pad lock on the entire breaker panel after the circuit is shut off. If this is not an option due to panel design or other reasons, a circuit lockout device should be used on the individual breaker. Always check at the point of work that all wires are de-energized as more than one circuit could be coming into the same junction box.
This man knows how to teach! thanks so much for your videos
My pleasure!
hi, your video was most helpful. I’ve put in many outlets before, but this particular case they want to add an outlet in the bathroom it has to be a GFI the only power I can get to on the other side of the wall there’s a kitchen outlet I guess the principal is the same, I guess I’m better off to also put a new GFI in the kitchen
I wouldn’t do that. Bathroom and kitchen circuits should be separate.
You explain things clearly and easy to follow thanks
Thanks so much 😊
Your video was so basic and simple to follow not like others, thanks
Thanks so much 😊
Thank you so much, this video will end up saving me lots of money. Perfect explanation of how to DIY new plug.
Glad it was helpful 👍🏻
Thanks for such a very well explained video sir, i need dummie proof videos when it comes to electrical and you've nailed it, thank you once again and keep it up!
Glad it was helpful 👍🏻
Remodeling our RV and this video was just what I was looking for. Thanks
Glad it was helpful 👍🏻
Thanks for the informative, Detailed video. I needed to make a new outlet for my computer & needed to know where to start.
Glad it was helpful 👍🏻
Great video. I'm handy at the basic level of DIY but I'm gonna give this project a go for our bathroom outlet. Thanks!
Be sure to use a GFCI in the bathroom.
@@handydadtv well said. I appreciate your immediate response! Love your videos!
Thanks 😊
What a great explanation. Clear, concise. It's a gift to be able to do that. Thank you.
Thanks so much 😊
Thanks for keeping it simple and clear. Enjoyed the explanation as to why as well. A fan.
Glad it was helpful 👍🏻
How many of these can you link together safely? Thank you for the video. Very straightforward and easy to follow.
Capacity is limited by the circuit breaker, not by the number of outlets.
I just did another one, this time it worked and then it didn’t. The breaker did not trip but I have no power on the outlet. There’s power coming from the breaker but it’s not going all the way to the outlet. Do you have any idea what happened?
@jrmsantana It’s impossible to say. You need to use a voltage meter and figure out where it was wired wrong. If you can’t figure it out, please call an electrician or qualified handyman.
I would add that it’s also limited by the size of wire. Make sure the wire size is correct for the breaker size.
I love and use Wago all the time! I love them!
Thanks 😊
Awesome video!!! This helps me a lot as I am going to finish a small room and just need a couple of outlets installed. Luckily the backside of both walls are exposed so easy peasy. Makes me feel confident now that I have to get it inspected. Well done!!
Let me know how it goes!
@@handydadtv my project went flawlessly. Thanks again so much for your very informative video !!!
Passed inspection?
your video was very informative and you simplified each step. Thank you.
Glad it was helpful 👍🏻
Instead of using the grounding butt connector, can I use the a pig tail and lever nut for ground as well?
Yes, or a wire nut.
This video was very easy to understand. Thank you.
Glad it was helpful 👍🏻
Clearly explained, Question, can I use this procedure when mounting a GFIC outlet on the exterior wall using the required waterproof box and enclosure? Thank you
Yes. Just connect the wires to the LINE screws on the GFCI.
Thank you for the quick reply
Great content here! Love everything except the mention of wago lever nuts having a higher operating temp range. I believe it is actually the opposite - most wire nuts have a higher operating temperature than Wago lever nuts.
It’s a moot point. Wire nuts and Wagos are rated for 105°C. Romex wire insulation is rated for 90°C.
@@handydadtv true.
Great content here! Love everything except the mention of wago lever nuts having a higher operating temp range. I believe it is actually the opposite - most wire nuts have a higher operating temperature than Wago lever nuts. Always check the manufacturer’s specs
I’ve seen testing on TH-cam. But regardless of the connector choice, the insulation on the wires melts first.
Thank you, I ordered both items to put in a plug this weekend!
You got this!
I have a light switch that turns my light off and a power outlet next to it. How would I fix this so the outlet remains on and the light turns off and on with the switch? Great content!!! This is my favorite new TH-cam channel.
Thanks but it’s impossible for me to say. This video showed you the basics. You need to open up your switch and outlet to see how they’re wired.
Makes sense. Thank you again and love your channel.
You're like my youtube dad now because i wish my dad taught me something like this.
My mission is complete.
Great demonstration. It was very straightforward
Thanks 😊
never mind someone else already asked this question, thank you!!!
Ok
Simple straight forward how to, thank you
My pleasure
This video definitely gives the information in a way that’s easy to understand, I’m going to add an outlet higher on the wall to mount a tv but the outlet I’m going to get power from his about 4.5 ft to the right and at the bottom of the wall. Anyway to run the Romex without going through the studs?
You could go up through the attic or down through the basement. Otherwise use this: amzn.to/2tC3mQJ
Perfect, I was able to add a receptacle by just watching your vid!
Glad it was helpful 👍🏻
Thank you for thoroughly explaining it and dumbing it down to my level.
Glad it was helpful 👍🏻
This is perfect, thanks for posting!!
Quick question…..
My existing outlet has line and load wires already. How do I tap isn’t the circuit? Use a junction box????!!!
Pigtails and wire nuts.
Thank you very much for this video, I did exactly what you thought and it worked perfectly. Thank you so much.
Glad it was helpful 👍🏻
You just made my life 1000x easier!
Glad it was helpful 👍🏻
Going to build a cargo trailer conversation to camper soon..and wanting to wire 120v shore power only for now..this is now something simple to do myself, thanks to you!
Glad it was helpful 👍🏻
Great info. Could you also provide some info on how to measure the load on the circuit before & after adding additional wall sockets?
The load doesn’t change by adding outlets to a circuit. Load comes from the devices plugged in and turned on. Here’s how I monitor circuit loads: th-cam.com/video/wnhNvfKy2rI/w-d-xo.html
Excellent explanation. You are God sent.
Glad it was helpful 👍🏻
This is an excellent video, thank you. I do have one question. What if the original outlet has 2 hot wires and 2 neutral already wired in? How do I attach the 3rd wire from the outlet I want to install?
Same as the grounds: Use a wire nut or Wago to connect all the wires with a pigtail (short length of wire) to the outlet.
Very informative video. Just had a question. Could you have created a pigtail for the ground wire just like you did for the black and white wires using one of those connectors? Or was there a reason you didn't? Thank you very much for your time and expertise.
Yes, I could have just used a wire nut and pigtail. No different electrically.
I had the same question thanks for answering
Thank you!
You're welcome!
Fantastic video nice and clear and very well explain, just what I need, regards and thanks for sharing be safe.
Glad it was helpful 👍🏻
Great video!!!! Question--: I have 2 outlets connected to each other in my bathroom walls, but I WANT TO REMOVE ONE OUTLET.... How do I do it?, and how to change the wires that go to this outlet I want to remove???? THANKS
Cap the wires and install a blank plate. Don’t cover a junction box in the wall.
Very easy to follow what you are doing. Thanks
Thanks 😊
So helpful. Annnnnd since you helped me scrutinize the details, I must tell you that I noticed at 5:34 that you have the black wire wrapped around the brass screw COUNTERclockwise. I wouldn't have noticed if you hadn't made a big point of it earlier in the video. Proof of good teaching! ;-)
Good eye!
Many thanks for your videos. I have watched several. They are extremely helpful. Do you have a video for a GFCI Receptacle installation with other outlets in-line? Thanks, again.
Gotcha covered
th-cam.com/video/inpvNt6591E/w-d-xo.html
Yes, thank you,, very helpful video. Been a carpenter all my life, but never messed with electrical.
I had "pro's" upgrade house to breakers, a ran a few new circuits.
But, had an after thought, and want to add another outlet up higher on the wall, for a wall mount tv. Still have one side of the drywall off, so much easier now, than later!
My question is if it is ok/safe to add another outlet. I wish I could send a pic, ha!, but I believe this new "tv" outlet would be the 3rd outlet on this new circuit.
PS: the pigtail thing went by a bit quick for me, but think I got it after watching it a few times, 😆 I hope I can find those little connectors.
I ass-ume, it doesn't matter in what "order" the source/hot wire, and the out going (2nd) black wire go into the connector? And then the 3rd "pigtail" wire(s) goes to source outlet.
Thanks again!
Technically, there is no limit to the number of outlets on a circuit. You’re only limited by the amperage capacity of the circuit. If you attempt to use too many devices at the same time, you could pop the breaker. The average 4K TV uses around 1 amp so that’s not going to be an issue for you.
Thank you for the video..I’m adding a fireplace in the wall and adding a extra outlet for it my question is to get the right wire that I need ?
I would only use the heater if it’s a 20-amp circuit. Check the number on the breaker.
If it’s a 20-amp breaker, use 12/2 wire to the new outlet.
If it’s a 15-amp breaker, consider running a new circuit if you intend to use the heater.
Great and not very complicated.very clear.thanks.
Glad it was helpful 👍🏻
I've never seen the through-grounding wire nuts FS here in California and ALWAYS use pigtails. ALWAYS check your local building codes to make sure that the connectors and methods that you want to use are allowed....
Thanks
Thanks for the easy video! was able to do some work in my place.
Glad it was helpful 👍🏻
I'm gonna go for it and I also subscribed. This will make my wife happy!
Thanks for subscribing! Welcome to the family!
thank you for helping me work on my house
Glad I could help 😊
Very helpful video! This should be good for a garage ready refrigerator, correct? I’m planning on adding another outlet for the fridge alone from one of the existing outlets in the garage. Thanks in advance!
Consider running a new circuit for the fridge because they use a lot of startup power and it could flicker your lights depending on whatever else is on the existing circuit. If it’s not an option, then sure you can extend an existing circuit.
Thanks for all the work you send my way. I get about 20-30% of my work as a state certified electrical contractor following behind "electricians", trunk slammers and DIY'rs who tried ONLY because someone like you on the internet gave them the confidence. Keep up the good work.
Will do 👌🏻
Vic, have you spent your entire life feeling insecure, or is that a new thing? The fact is a lot of what you do can be taught by guys on TH-cam.
@@patty109109 Taught wrong...5:37 code violation ....black screw wrapped the wrong direction around terminal screw....FAIL
Awesome. Thank you. I was looking for the ground connection part. It's been many videos to find this. I figured it must be a wire nut.
Glad it was helpful 👍🏻
My project is a 220 volt In conduit the A/C is Hardwired outside in a junction box on the unit , I need to run a line through siding inside and install an outlet to plug the new A/C into - old circuit breaker is 20 amp new one calls for
15 amp breaker - biggest thing now is get the 35 year old Kenmore through the wall A/C out
35 years!!! I’m sure the new one is more efficient, but it certainly won’t last as long as the Kenmore.
@@handydadtv No doubt it won't last that long
but than neither will i
Great job explaining it to a newbie like me. Thank you Dad.
My pleasure
Awesome, thanks for this. Quick and concise.
Glad it was helpful 👍🏻
yoooou are the best, thank you so much for making such a straightforward and easy to follow tutorial!
Thanks 😊
Thanks for this video! I’m in this situation adding an outlet on the other side of our bathroom vanity. Any special steps for adding the second outlet from a GFCI outlet?
I’ll be doing a video specifically on this topic soon because it’s a common question. But this video will also help you: th-cam.com/video/dbmRETinw0A/w-d-xo.html
Thank you!
thanks going to use this on an office luckily it is a new room and I can easily get to wires. When would you want outless on their own breaker?
I’d put the office outlets on a separate circuit because computers, monitors and printers draw a healthy amount of current, especially if you have more than one workstation. Especially if you have walls open.
Excellent,excellent explanation! Thank you.😊
Thanks so much 😊
Appreciate that unc, that was well explained and very detailed. I’m glad I made it to this video🤝
Glad it was helpful 👍🏻
So simple 👏🏼 thanks! Question tho! Can I add another outlet from the new out let ?
So it would be
Existing O.L.--new O.L.--new O.L. ???
Yes just repeat the process.
New follower, exactly the knowledge I was looking for.
Thanks for subscribing! Welcome to the family!
Great video. Could you add two outlets downstream in the same way? Original outlet to a new outlet #1 to a new outlet #2?
Yes. Just repeat.