In reference to your comment about hard drive errors found by chkdsk: The chkdsk without options finds file system errors but does not fix anything. The chkdsk /f /r is redundant. The /r implies (includes) the /f. The /f option checks the file system and runs more quickly. The /r option checks the whole drive and looks for file system problems and physical disk errors (or what appear to be physical disk errors). As a point of experience (45 years), i have seen many drives report 'bad sectors' in chkdsk that were fixable. 90% of ALL problems are soft! This is based on Dell Tech reports on service calls. Only 10% of problems require a part. The rest are fixed by rebooting, reformatting, or re-installing. (of course if you reformat you will need to re-install but Windows also has a repair re-install option that fixes many problems). Of the 10% parts replaced 50% which are received at the warehouse are GOOD! Typically these are drives that have already FAILED some form of diagnostic tests. I personally have had drives that reported bad sectors which were fixable and used without incident for years. I would recommend the next drive you have bad sectors on which you are going to throw away (you send to me -- thanks) recover any data you need to then simply re-format the drive. Don't even bother using any programs like Spinrite to recover it --- you were going to throw it away anyway. Just reformat it and re-run chkdsk /r. See if it gives you any bad sectors. Even if it does give you bad sectors it will probably give you fewer. In my experience the majority of the time that alone will fix the drive without any bad sectors.. Bad sectors CAN be caused by physical defects in the drive in which case the drive may indeed deteriorate. 90%+ however are caused by soft problems such as mis-writes which are easily correctable. If a drive spins it is almost always recoverable (and there are a lot of TH-cams that solve non-spinners).
Guys who had getting this problem just do the following step 1). Press ctrl alt del at the same time. 2).at the right bottom there is power option while pressing or holding shift key then restart. 3). Then advanced repair tool will open. 4). Go to troubleshoot; advanced; startup; and then boot from safe mode 5). After it will start your computer on safe mode and then you can just restart your pc. This one's work for me but i dunno if will work good all users or not i had tested this on Windows 10
Amazing!!! My laptop has been with this problem since a year and unfortunately the person I gave it to fix could not fix it.But thanks to you mister my fixed my laptop at home I followed all the steps but didn't have to change the drive ones again thanks!!❤️
Thank you so much for guidance. I recovered my laptop just by that restore option. As my laptop took daily backup it was quite convincing for me. Thanks a lot.... you saved my money.😊😘
As your comment was year ago, you must've already either fixed it or reinstalled. I had the same thing, but I managed to get over it. First I wrote ''ICACLS e:\windows\winsxs'' and then repeated the ''sfc /scannow /offbootdir=e:\ /offwindir=e:\windows''. No more protection blah blahh.
Dam DibiDum Well I Do have the problem that if I type: sfc scannow offbootdire... it doesn't work. It says something about that it can't start. But when I was typing your: ICALS e: Windows... It didn't work as well and it says that it isn't ready. The same error came when I was typing e: .
This happens because there is an "bug flag" on the system making the whole drive inacessible (read/write off). What you have to do to make it boot again is follow the steps in this video until the system recovery step (restore a previous recovery point can solve the problem). If the steps can`t solve it, install Windows on a new hard drive and boot the new one. Make sure the old one is connected as disk number 2 (slave). When the new system boots up, try to double click on the old disk... the system will return "Access deny". So you right click on the old disk, select properties option, go to "security" tab and adds full control permission to all (or everyone). It will take few or several minutes, depending on how much files is in there. It`s not an ideal sollution but it works (and it`s the only one I discovered). After doing that, back up all your files, export all important software preferences and format the whole disk with a fresh Windows install. Using Windows with everyone having full control is not safe AT ALL... Do this only to recover your files. You can connect your HD on another computer (if you have another one) and do the same without having to install a new windows on a new hd. Hope it helps someone! I had to figure it ou by myself on an client server (all system ERP and production down). I had to do this to the ERP of the company comes back as fast as possible and format a new HD on an holiday without people working.
Please, how did you image your disk without login into Windows ? I'm encountering the same trouble.. I can run on Linux Ubuntu, do you think it might work if I image the disk from Linux ? (I guess yes.)
I guess he used another computer and one of those external drive enclosures where you insert your damaged hdd then connect it over usb to the second computer and you see it as an external drive
Just a small tip that made me feel like an idiot after I found out. If you have 2 monitors plugged in (I had my monitor and my TV, which was off) check to make sure that the one that is off isn't set as the primary monitor. I was fiddling around for hours trying to figure out what the problem was until I started pulling cables out of my vid card and remembered that I had 2 monitors plugged in.. And then I figured that my tv was set as the primary monitor... And I was having the black screen with the mouse problem.. Lol. Derp. Hope this helps someone :D
+Victor Parker I use two monitors and I have the same problem, but I dont understand how you fix it... The problem stars after change some things on the screen window... how can I fix it. can you help me?
December 2017 here! Chkdsk works for me. It says something about “windows replaced bad cluster” and this method takes about 30-40 mins for me. and I sincerely thank you uploader. U save my night. You’re a lifesaver. THANK YOU SO MUCH 😊
Nothing happened while pressing alt+control+delete at the same time in my laptop!.it's still on the same position of black screen and cursor!. What to do and how to fix it in Windows 10???
Solution: In my case it was a black screen with cursor before login.Noting was working before not a single method even i was not getting safe/recovery mode.But i troubleshoot this simple way: (1) If safe mode is also not coming then try to boot to recovery mode by powering on ur laptop once booting starts and u get the first logo image of manufacture press & hold power off button till 12-15 secs.Repeat the steps atleast two or 3 times max and u will get to recovery. Next if ur system can boot to safe mode or restore previous mode in advance section under recovert then it will be easy to get this issue fixed.In my case my system got failed to boot in to safe mode/restoring to previous windows version i somehow found a way by going to troubleshoot option under recovery advance oprion and clicked uninstall recent updates if u upgrade the os or upgraded to Windows10 from windows 8/8.1 this issue happens.Then after i uninstall recent updates i turn off device and restart,my system automatically restore to my previous version which is windows 8.1.Thats it issue fixed.
I had used the Tweaking.com version 4.0.9 in safe mode, rebooted, and got the black screen of death. I followed your steps and did the F8, but wouldn't run in safe mode, so I had to choose running it in the last known good configuration. That helped. I'm back in Windows 7 again, up and running. I won't be using Tweaking.com 4.0.9 again.....ever.
Hi thanks for getting trough every step here. I also would like to suggest to try and use HDD Regenerator tool. Maybe from Hiren's boot cd or other place, from pendrive or CD. Maybe check it externally. It should help and of course if it has problems You should transfer all your data to a new disk. Thx.
Another way that I solved this is I went into safe mode, advance settings and went too boot options and select your SSD as main boot up device when starting up PC. Once you done that it should load properly. I just did it as we speak and it's running like nothing happened. I would suggest to change a few things while you have access. Just thought I recommend it. Give it a go it might/might not work. All the best.
Hello, firstly I have to thank you for the pretty in-depth und very helpful video. I'm currently doing the check disk step for hard drive C. Is it possible to do the same for another hard drive E without overwritting the first one? Thanks for quick answering.
I know I'm late, but for anyone who looks up this in the future: Basically what he said in the last part was that the hard drive he had on his hand was the one that he was trying to fix throughout the video, the one he was showing us which wasn't working. So, he got a new hard drive which he bought and copied everything into the new one by imaging it after pressing F8 at startup and choosing the Repair option and the the Image Recory option after that (all of this in the new hard drive, not the broken one), but since the hard drive was corrupted he might have lost some of his files. TL;DR: if everything else failed, you either want to reinstall Windows or get a new hard drive and do an Image Recory there from your old hard drive.
My computer isn’t allowing me to use system restore. I can click on the point in time that I want to restore to but I can’t actually get it to restore it to that point.
When I reboot my laptop it comes back on . Let me take you back lol . When I'm on my laptop some times. The screen will go black . But I can move my cursor around . Please tell me what is wrong . Because I tried the whole battery thing . For thirty seconds I didn't see no Hp logo . It just beeped then went off . Please explain to me what should I do ..??
I don't even have a cursor on the screen. The black screen happened when the power was cut during a Windows Update and before it was finished. When I turned on and rebooted the computer the tower came on, the fan was running, but the screen stayed black.
hi i have a similar problem of ur PC..but mine found some problem. it says "windows protection found corrupt files but was unable to fix some of them. details are included in CBS.Log windinr\Logs\CBS\CBS.log." and it shows an example of "c:\windows\Logs\CBS\CBS.log". what to do next
Reinstall Windows. Get someones laptop or pc, get an 8gb or 16gb flash drive, and download Windows ten on it. Look up a tutorial on how to install Windows 10 on TH-cam and then follow that. They will also show you were go get it
E and c scanning it said "windows resource protection could not start the repair service" so i tried 'D' and it said "windows resource protection could not preform the requested operation". What do i do ??
Hi R3DLN3S! The program you used to image (or clone) the Hard Drive was the "Acronis True Image"? This process works with a "corrupt" Windows, for example the classpnp.sys error?
Just get CD for Window System 8/9/10 whichever you like and install it ( sucks part you have to delete everything you had on pc . But at least it will work again)
My computer is having this problem...I tried this but it is working.When I press shift key 5times it shows dialog box of sticky keys...can you pls tell me how to replace it with command prompt...pls
@@loading739 No. It says "Starting Windows" then goes black- the login screen never comes on. I'm on my computer now- but it's at that giant screen phase and won't revert back. Also, if I reinstall the AMD Radeon HD 7800 that I previously uninstalled to get it to this point- it will revert back to the black screen =( I think my graphic card is just dirty- there's a lot of dust in my puter, I'm waiting on the hand vacuum I ordered to clean it. Hopefully that works.
I'm getting that the scan found some corrupt files but could not fix them. I ran the \Windows\Logs\CBS\CBS.log and then it said access denied. Now how do I fix this? Your instructions were very clear and I got through most of the checks without a hitch. Can you help me figure it out?
Thank you very much! Fortunately the restore point worked and I am able to run a virus scan. Who knows yet what went wrong but I will never forget this video and I am a happy subscriber!
I was watching this video on my ipad and i was so scared that when dad is gonna who did it he would be so angry at me and that is where the magic happend the comp was open it was just black screen before watching this video and in the middle of this vid i looked at my comp and it was again that win 7 desktop
I never comment on these but I just have to say, THANK YOU! Yours was the only video I found that worked for me and my computer problem! Wish you good karma 😃
Same problem on laptop Thanks for the help! Finally, I got it fix! Ur a useful person! Though it went to Vista.... On reparing computer part but it eventually got to 7
Guys i found a easy way! Do the following: 1. Start Safe Mode (i guess) 2. Wait for it to finish reading the files 3.wait until the side of the cursor has the loading logo 4. I dont know and its done
ALSO, if you have a 2ndary monitor connected to your computer try turning it on during boot. I know there has been a couple times where my "duplicate desktop on 1 and 2" got turned off and my 2ndary monitor (which the computer sees as my primary because of how the hookup work) becomes the primary screen... the one with the boot info, icons, etc. It is just a matter of logging in on that screen and going into display settings and switching the "duplicate desktop on 1 and 2" back on... or whatever settings you normally use.
It's easy to fix First start your pc and after login windows+r type services.msc ok Find appreadiness stop it and disable click on apply It will be fixed
I did everything but I saw no results... Finally, I found my patience and did the old good recipe: backup the data, format the HDD and run a clean installation of the Windows 7. But thanks for your video man!
My F8 didn't work at first either- try restarting it back to back about 4 times- it'll get sick o'the bullshit and give you the "Start Windows Normally/Start Windows in Safe Mode" boot screen. Once you're in, open a command window by typing 'cmd.exe' into the File>New Task (Run) Dialog box. When it opens type "bcdedit /set {default} safeboot minimal" [Press Enter] to keep it opening in Safemode until you can fix your problem. To revert back to normal boot- do everything the same but replace '/set' with '/deletevalue' [Press Enter]
This black screen issues was happened to me but it worked fine until i wait for the black screen, i mean like you need to wait for the black screen then the dekstop icon will show up then,any fix for that? Please the black screen was really anoying me even its still running like a normal
It fixed the problem persistentle my windows opens in safe mode after runing explorer.exe and again after logging off the same problem arises. Do i have to run explorer.exe everytime i open my desktop.
Startup repair worked for me, ended a 2 hour battle with Dell. Thank you so much!
How did you do it
🥺
The ‘Repair Your Computer’ option is missing for me :/
Tried safe mode, just black screen
انت نفس مشكلتي الاكسبلور عندك خربان لازم تسوي فورمات
@@dangerxsaleha5037 غريبه عرب
@@ammarys9980 دايما الاجانب حلولهم متعمقه وتشتغل الي عندنا تلقاه طباخ وقاعد يفتي بالكمبيوتر
@@dangerxsaleha5037 وتلقى هموا الاكبر الفلوس
@@dangerxsaleha5037 بس لا نكذب في ناس تخلص بعملها من العرب
I follow your steps from here( 6:28 )
And this solved my problem........
thanks for this video
It does work and bring my windows 7 back, after I ran the "chkdsk" and "sfc". It is really appreciated, many thanks.
Mine won't show the cursor and it's just going green to black
It worked
@@QualityFTF new pc or hard disk
Awesome advice. I am not tech savvy at all, but managed to get through the system restore and got my lap top back up and running. Thank you so much!!
I'm crying right now my mom's sensitive stuff is on there and nothing is working I know my mom is going to beat me.
My dad gonna beat me im crying too
My whole family is gonna kill me!!!
Same here
My brother gonna kill me 😭 bro
My dad is angry
when i click on task manager an error;this program not open correctly was occur how to solve it
In reference to your comment about hard drive errors found by chkdsk:
The chkdsk without options finds file system errors but does not fix anything.
The chkdsk /f /r is redundant. The /r implies (includes) the /f.
The /f option checks the file system and runs more quickly.
The /r option checks the whole drive and looks for file system problems and physical disk errors (or what appear to be physical disk errors).
As a point of experience (45 years), i have seen many drives report 'bad sectors' in chkdsk that were fixable.
90% of ALL problems are soft!
This is based on Dell Tech reports on service calls. Only 10% of problems require a part. The rest are fixed by rebooting, reformatting, or re-installing. (of course if you reformat you will need to re-install but Windows also has a repair re-install option that fixes many problems). Of the 10% parts replaced 50% which are received at the warehouse are GOOD! Typically these are drives that have already FAILED some form of diagnostic tests.
I personally have had drives that reported bad sectors which were fixable and used without incident for years.
I would recommend the next drive you have bad sectors on which you are going to throw away (you send to me -- thanks) recover any data you need to then simply re-format the drive. Don't even bother using any programs like Spinrite to recover it --- you were going to throw it away anyway. Just reformat it and re-run chkdsk /r. See if it gives you any bad sectors. Even if it does give you bad sectors it will probably give you fewer. In my experience the majority of the time that alone will fix the drive without any bad sectors.. Bad sectors CAN be caused by physical defects in the drive in which case the drive may indeed deteriorate. 90%+ however are caused by soft problems such as mis-writes which are easily correctable.
If a drive spins it is almost always recoverable (and there are a lot of TH-cams that solve non-spinners).
Guys who had getting this problem just do the following step
1). Press ctrl alt del at the same time.
2).at the right bottom there is power option while pressing or holding shift key then restart.
3). Then advanced repair tool will open.
4). Go to troubleshoot; advanced; startup; and then boot from safe mode
5). After it will start your computer on safe mode and then you can just restart your pc.
This one's work for me but i dunno if will work good all users or not i had tested this on Windows 10
😆😑😆😀😆😑😑
nothing happens when i press the shift key
Really man you saved my life. After restore it worked thank you soooooo much.
And will it happen again? And how to prevent please reply.
PLZZ solved my problem it request
@@sumedhkumar1709 what problem bro
@James Peralta selected restore it, and it worked
Amazing!!! My laptop has been with this problem since a year and unfortunately the person I gave it to fix could not fix it.But thanks to you mister my fixed my laptop at home I followed all the steps but didn't have to change the drive ones again thanks!!❤️
Thank you so much for guidance. I recovered my laptop just by that restore option. As my laptop took daily backup it was quite convincing for me. Thanks a lot.... you saved my money.😊😘
HAHAHAH
my laptop turns black
I can't reach the windows repair screen, if I choose safe mode, system repair...etc - I still receive a black screen with cursor
P.a.C ⓢⓐⓜⓔ
P.a.C me too!! if you have a fix, let me know please
It didn't seem to work for me but if you leave it on the black screen for about 10 to 20 minutes and then will appear
Same
same !
At 2:32 I get less options only safe mode and start windows normally but not like the ones mentioned in the video
Did you fixed?
I got headache watching this video. So is there any solution at all?
I only didn't go batshit crazy while trying these, because of how nice and calming your voice is.
11:45 after pressing enter after sfc/scannow etc. it says "windows resource protection could not start the repair"
Rohit Raut same
You've to use the detailed command:
sfc /scannow /offbootdir=e:\ /offwindir=e:\windows
As your comment was year ago, you must've already either fixed it or reinstalled. I had the same thing, but I managed to get over it. First I wrote ''ICACLS e:\windows\winsxs'' and then repeated the ''sfc /scannow /offbootdir=e:\ /offwindir=e:\windows''. No more protection blah blahh.
Dam DibiDum Well I Do have the problem that if I type: sfc scannow offbootdire... it doesn't work. It says something about that it can't start. But when I was typing your: ICALS e: Windows... It didn't work as well and it says that it isn't ready. The same error came when I was typing e: .
Dam DibiDum Any leads?
This happens because there is an "bug flag" on the system making the whole drive inacessible (read/write off). What you have to do to make it boot again is follow the steps in this video until the system recovery step (restore a previous recovery point can solve the problem). If the steps can`t solve it, install Windows on a new hard drive and boot the new one. Make sure the old one is connected as disk number 2 (slave). When the new system boots up, try to double click on the old disk... the system will return "Access deny". So you right click on the old disk, select properties option, go to "security" tab and adds full control permission to all (or everyone). It will take few or several minutes, depending on how much files is in there.
It`s not an ideal sollution but it works (and it`s the only one I discovered). After doing that, back up all your files, export all important software preferences and format the whole disk with a fresh Windows install. Using Windows with everyone having full control is not safe AT ALL... Do this only to recover your files.
You can connect your HD on another computer (if you have another one) and do the same without having to install a new windows on a new hd.
Hope it helps someone! I had to figure it ou by myself on an client server (all system ERP and production down). I had to do this to the ERP of the company comes back as fast as possible and format a new HD on an holiday without people working.
Thank you! This is the only thing that helped in my case...
Okey im goin to install new windows but how can i do it while it has blue screen
Rip man you have the blue screen of death
I don't know what else to say, but thank you so much. This helped me a lot, I'm so glad I stumbled upon your video.
Please, how did you image your disk without login into Windows ?
I'm encountering the same trouble.. I can run on Linux Ubuntu, do you think it might work if I image the disk from Linux ? (I guess yes.)
Skyern Aklea I’d guess no
I guess he used another computer and one of those external drive enclosures where you insert your damaged hdd then connect it over usb to the second computer and you see it as an external drive
@@annelisemeier283 ggg
Guys try doing CTRL+ALT+DELETE! THSI ACTUALLY WORKS!!! I did and it saved me!!! Not lying! 😭
Just a small tip that made me feel like an idiot after I found out. If you have 2 monitors plugged in (I had my monitor and my TV, which was off) check to make sure that the one that is off isn't set as the primary monitor. I was fiddling around for hours trying to figure out what the problem was until I started pulling cables out of my vid card and remembered that I had 2 monitors plugged in.. And then I figured that my tv was set as the primary monitor... And I was having the black screen with the mouse problem.. Lol. Derp. Hope this helps someone :D
Victor Parker I actually think it might work xD
+Victor Parker You are a hero. This was my problem!
+Victor Parker I use two monitors and I have the same problem, but I dont understand how you fix it... The problem stars after change some things on the screen window... how can I fix it. can you help me?
+Victor Parker You saved my night, this was my freaking problem too, thanks in advance!
Jorge Eduardo Rodriguez :) Glad i could help lol. I still remember to this day pulling my hair our trying to figure out the problem, cheers
So I have a windows vista home premium and I press F8 and it comes up with the advanced options however theirs no repair laptop option please help
My sticky keys pop up but I can't find vid on opening command prompt
Mine doesn’t have the restore option after F8. Any option I pick it just goes back to a black screen. No curser either
December 2017 here! Chkdsk works for me. It says something about “windows replaced bad cluster” and this method takes about 30-40 mins for me. and I sincerely thank you uploader. U save my night. You’re a lifesaver. THANK YOU SO MUCH 😊
Nothing happened while pressing alt+control+delete at the same time in my laptop!.it's still on the same position of black screen and cursor!. What to do and how to fix it in Windows 10???
thank you soooo much i was freaking out ^^ i woke up and it was so messed up.
when i try to go to repair mod it says that it need a administrator password pls help
Nothing worked I've tried all of the things listed
I think ur computer is dead ... 💀
Same I did everything!
I am getting sticky keys box but not the task manager.... Please anyone tell me sticky keys method.....
Thank you so much this helped me alot now i can pringt again for school projects and do gaming
It's not opening though clicking
Ctrl-altr-del.
Shift-5times.
Any other solution?
hello i managed to login into safe mode
what should i do next to login normally
ye ur totallynotapictureofyou profile picture looks pretty sweg.
😈😇😈😇🙏🙏🙏🙏🙏🙏🙅😭😭😭😭😭
Solution:
In my case it was a black screen with cursor before login.Noting was working before not a single method even i was not getting safe/recovery mode.But i troubleshoot this simple way:
(1) If safe mode is also not coming then try to boot to recovery mode by powering on ur laptop once booting starts and u get the first logo image of manufacture press & hold power off button till 12-15 secs.Repeat the steps atleast two or 3 times max and u will get to recovery.
Next if ur system can boot to safe mode or restore previous mode in advance section under recovert then it will be easy to get this issue fixed.In my case my system got failed to boot in to safe mode/restoring to previous windows version i somehow found a way by going to troubleshoot option under recovery advance oprion and clicked uninstall recent updates if u upgrade the os or upgraded to Windows10 from windows 8/8.1 this issue happens.Then after i uninstall recent updates i turn off device and restart,my system automatically restore to my previous version which is windows 8.1.Thats it issue fixed.
Ctrol+alt+del works
Now how do I fix it?
Lucky
I had used the Tweaking.com version 4.0.9 in safe mode, rebooted, and got the black screen of death. I followed your steps and did the F8, but wouldn't run in safe mode, so I had to choose running it in the last known good configuration. That helped. I'm back in Windows 7 again, up and running. I won't be using Tweaking.com 4.0.9 again.....ever.
What may the problem be if the screen doesn't show ANYTHING but the cursor?
then that is probably a broken drive,if that dosent work to restore it, reinstall windows or buy a new pc.
Thedarklord 2007 what a genius . idiot!
Thedarklord 2007 will it work again if I just buy a new hardrive
Phantom Prince yes it will, make sure u replace the broken drive
Or switch to a mac.
Yea but what we should do if we cant open ctrl alt delete or run computer in safe mode cuz i got same problem in safemode too?
What do you do if "windows resource protection could not Start the repair service"
Tim The Enchanter I'm having the same issue - did you find out how to fix? Thx
A Durden have u guys found a fix for that step? I'm having the same problem
you guys are either wrote it wrong or your system folder directory isn't e. Try c d x etc.
Hi thanks for getting trough every step here. I also would like to suggest to try and use HDD Regenerator tool. Maybe from Hiren's boot cd or other place, from pendrive or CD. Maybe check it externally. It should help and of course if it has problems You should transfer all your data to a new disk. Thx.
9:50 it's show "failed to transfer logged messages to the event log with status 50"
C:\>
C:\>huff j1
dis anyone know how to fix it
thankfully my computer started after ctrl+alt+del..thnk u very useful and productive video
it was intense... I never expected it was this simple... thanks for the video...
Another way that I solved this is I went into safe mode, advance settings and went too boot options and select your SSD as main boot up device when starting up PC. Once you done that it should load properly. I just did it as we speak and it's running like nothing happened. I would suggest to change a few things while you have access. Just thought I recommend it. Give it a go it might/might not work. All the best.
Task Manager, New Task, "Explorer" worked for me . . .
Thanks man xXx
But you have to do it every time you open your pc?
Soundcloud smackers i do it every time i open mu pc xD (cntr/alt/del) new task manager and i chose explorer.exe ..you mean smth different?
@@emiliomp8812 Yeah, but my PC is on pretty much 24/7. I only shut it down a coupla times a month so it's no biggie . . .
The issue you had while running he command at 10:53 is the same i am encountering . Still is saying that a reboot is required . How to get past that?
my laptop had this problem so i took the battery out, hold start button for 30 secs and then start it and it worked.
this might work for you guys too
Thanks, this really helped
but i have intern baterry...
PikaCiuca you're gonna have to unscrew dem bolts, i'd reccommend not doing that if you havent dissasebled a laptop cuz you might damage some parts
+Luka lomidze omfg thanks, i was fixing my moms slow laptop and this happened to me and i thought i broke it.
What if my battery don't work
Hello, firstly I have to thank you for the pretty in-depth und very helpful video. I'm currently doing the check disk step for hard drive C. Is it possible to do the same for another hard drive E without overwritting the first one? Thanks for quick answering.
2:47 worked for me lol
See if u can fix by doing this
And yes u got a sub
Keep it up
Man, f i was so worried about this
I was typing a long paragraph in Wordpad and suddenly it went all black with cursor is there no way to retrive it?
Tnx bro u have saved my time and money.i can't express my feelings,when i saw it working again.keep it up👍
Does my system loose any files using this method???
that last part, I didn't get it at all, im new in this 😞
I know I'm late, but for anyone who looks up this in the future:
Basically what he said in the last part was that the hard drive he had on his hand was the one that he was trying to fix throughout the video, the one he was showing us which wasn't working. So, he got a new hard drive which he bought and copied everything into the new one by imaging it after pressing F8 at startup and choosing the Repair option and the the Image Recory option after that (all of this in the new hard drive, not the broken one), but since the hard drive was corrupted he might have lost some of his files.
TL;DR: if everything else failed, you either want to reinstall Windows or get a new hard drive and do an Image Recory there from your old hard drive.
@@ticktockbam you bloody legend
My computer isn’t allowing me to use system restore. I can click on the point in time that I want to restore to but I can’t actually get it to restore it to that point.
Me too. I have the same problem.
When I reboot my laptop it comes back on . Let me take you back lol . When I'm on my laptop some times. The screen will go black . But I can move my cursor around . Please tell me what is wrong . Because I tried the whole battery thing . For thirty seconds I didn't see no Hp logo . It just beeped then went off . Please explain to me what should I do ..??
I don't even have a cursor on the screen. The black screen happened when the power was cut during a Windows Update and before it was finished. When I turned on and rebooted the computer the tower came on, the fan was running, but the screen stayed black.
hi i have a similar problem of ur PC..but mine found some problem. it says "windows protection found corrupt files but was unable to fix some of them. details are included in CBS.Log windinr\Logs\CBS\CBS.log." and it shows an example of "c:\windows\Logs\CBS\CBS.log". what to do next
Mine too! What to do?
Reinstall Windows. Get someones laptop or pc, get an 8gb or 16gb flash drive, and download Windows ten on it. Look up a tutorial on how to install Windows 10 on TH-cam and then follow that. They will also show you were go get it
E and c scanning it said "windows resource protection could not start the repair service" so i tried 'D' and it said "windows resource protection could not preform the requested operation". What do i do ??
Best fix for this is Installing whole Windows again !!!
Ivan Zima im trying to install a new windows again but while processing to install the new windows it became like this..huhu pls need help
The problem persists after re intalls the Windows
@@olmedodiego10 its a graph driver
Hi R3DLN3S! The program you used to image (or clone) the Hard Drive was the "Acronis True Image"? This process works with a "corrupt" Windows, for example the classpnp.sys error?
Mines saying "boot manager is missing" I have no idea what to do! I've tried everything! RIP I guess
Me too!
Just get CD for Window System 8/9/10 whichever you like and install it ( sucks part you have to delete everything you had on pc . But at least it will work again)
@@dzemilabih4938 thx man. That's what I actually had to do awhile back but I'm up n running again 😁
My computer is having this problem...I tried this but it is working.When I press shift key 5times it shows dialog box of sticky keys...can you pls tell me how to replace it with command prompt...pls
Is there a vid for [without mouse]?
Do you have when it asks for your log in then it shows just black screen and when your actually in the computer then it just shows nothing but black?
@@loading739 No. It says "Starting Windows" then goes black- the login screen never comes on. I'm on my computer now- but it's at that giant screen phase and won't revert back. Also, if I reinstall the AMD Radeon HD 7800 that I previously uninstalled to get it to this point- it will revert back to the black screen =( I think my graphic card is just dirty- there's a lot of dust in my puter, I'm waiting on the hand vacuum I ordered to clean it. Hopefully that works.
@Dominique McQueen Did you fix your computer??
@@amitkhadka1910 No my graphics card is filthy- I need to vacuum out the inside of the entire box as soon as I find a nice hand vacuum
The fact that there are 900 odd thumbs down on this video is insane.
Good video 👍
thank you so much, i just used the keys "ctrl+alt+del" and went to task manager file run, typed "explorer.exe" and it worked
An unspecified error occurred .
Show during chkdsk /f/r ✓
Which type of problem it is can you tell me please...
same with me... i hope it is not my hdd...
That cmd scan of yours saved me big time. Many thanks to you bro
Thanks buddy... System repair did the job for me... I was really worried.. Tried everything... And at last system repair did it!!
mines so bad i cant even do f8
Do a system restore. I did and it went back to normal
Michelle Jackson how do i system restore
Go to Accesories on your Start button under programs. Click system restore and click a previous date when your pc worked better.
Michelle Jackson Dude his Pc does not start! How should he do that
+Michelle Jackson where the start button? can't find!
I'm getting that the scan found some corrupt files but could not fix them. I ran the \Windows\Logs\CBS\CBS.log and then it said access denied. Now how do I fix this?
Your instructions were very clear and I got through most of the checks without a hitch. Can you help me figure it out?
My laptop just loads straight into the start up repair screen and I did everything and still doesn't work.
Bro i have the same problem . Pls tell me if you already fix the problem thanks
Same
System restore worked for me on windows 7 x64. Thanks you’re a life saver.
Straight to the point, 5 stars
Thank you very much! Fortunately the restore point worked and I am able to run a virus scan. Who knows yet what went wrong but I will never forget this video and I am a happy subscriber!
I was watching this video on my ipad and i was so scared that when dad is gonna who did it he would be so angry at me and that is where the magic happend the comp was open it was just black screen before watching this video and in the middle of this vid i looked at my comp and it was again that win 7 desktop
I never comment on these but I just have to say, THANK YOU! Yours was the only video I found that worked for me and my computer problem! Wish you good karma 😃
This is an amazingly well crafted and detailed repair video👍
Thnx a lot man.....all other videos regarding this topic are either worthless or don't have much info.....really appreciate it
Thank you very much you havr saved the amount of money I was about to spend to fix my pc. such a simple thing thay fixed all my problems :)
Safe mode does the exact same thing a normal boot, black screen with cursor after boot
Same problem on laptop
Thanks for the help!
Finally, I got it fix!
Ur a useful person!
Though it went to Vista....
On reparing computer part but it eventually got to 7
OMG this video totaly saved me and all my work. Finally return to previous settings worked
Guys i found a easy way! Do the following:
1. Start Safe Mode (i guess)
2. Wait for it to finish reading the files
3.wait until the side of the cursor has the loading logo
4. I dont know and its done
ALSO, if you have a 2ndary monitor connected to your computer try turning it on during boot. I know there has been a couple times where my "duplicate desktop on 1 and 2" got turned off and my 2ndary monitor (which the computer sees as my primary because of how the hookup work) becomes the primary screen... the one with the boot info, icons, etc. It is just a matter of logging in on that screen and going into display settings and switching the "duplicate desktop on 1 and 2" back on... or whatever settings you normally use.
It's easy to fix
First start your pc and after login windows+r type services.msc ok
Find appreadiness stop it and disable click on apply
It will be fixed
No Such Thing Windows 7
Someone used my computer remote control to scam me, left computer on safe mode. I can't get out of it. How do I do that?
Man i cant even press f8 for menu option plz help me
Change the keyboard if u have a USB keyboard
+MΣNT0R9™ f {"cpnf":v 9nnlolojbtf
myron patton ؟
MΣNT0R™ idk what happen think i had google plus open in my phone inside my pocket my bad
myron patton xD all good
I did everything but I saw no results... Finally, I found my patience and did the old good recipe: backup the data, format the HDD and run a clean installation of the Windows 7. But thanks for your video man!
Great if F8 works but it doesn't
My F8 didn't work at first either- try restarting it back to back about 4 times- it'll get sick o'the bullshit and give you the "Start Windows Normally/Start Windows in Safe Mode" boot screen. Once you're in, open a command window by typing 'cmd.exe' into the File>New Task (Run) Dialog box. When it opens type "bcdedit /set {default} safeboot minimal" [Press Enter] to keep it opening in Safemode until you can fix your problem. To revert back to normal boot- do everything the same but replace '/set' with '/deletevalue' [Press Enter]
Does system restore only affect system files? Or does it also affect user files?
Tnx allot i choose the system imagery recovery tnx allot i appreciate you you save my pc and my life!
This black screen issues was happened to me but it worked fine until i wait for the black screen, i mean like you need to wait for the black screen then the dekstop icon will show up then,any fix for that? Please the black screen was really anoying me even its still running like a normal
Fake video ku banata ho
It fixed the problem persistentle my windows opens in safe mode after runing explorer.exe and again after logging off the same problem arises. Do i have to run explorer.exe everytime i open my desktop.
I'm at 9:21 and so far it's going well.. praying that it's gonna "check out" and be fine..
Hey man can you help me I did ctrl+alt+del and even f8 it doesn't work it's stuck in black screen, please help.
Knight mare I am having the same problem with my dell laptop did you ever fix your if did what did you do to fix it
@@annieferrell7172 I haven't fixed it so far i am trying all buttons but nothing
@@knightmare9741 what about now?
Thank you very much, you really helped me repair my laptop 👍
my problem got solved within 50 seconds...You are just awesome!!!!