Ok,, so my earlier comment was before I watched the entire video,,, so here’s the proper method,, first , give the chips a HLC bath on a slightly warm hot plate to remove all solder,, you will know when it’s done, when it stops bubbling but the acid will still react with a VERY small pinch (a few grains) of baking soda,, then you remove ( pour off) all HLC for reuse,, second wash,wash,wash with water until a test strip reads neutral (7)... now your ready for GOLD X solution,, do it the same as you did before,, but this time DONT USE ZINC,, you contaminate your precious metals when you use zinc,,, USE activated charcoal,,, when the charcoal is done you wash it with water a couple of times then melt,,, it’s a lot easier than your first approach,, and the solution in the video most likely still has PM’s in it,, you used way too much Nitric Acid ,, that’s why you didn’t have a immediate drop of gold when you added SMB,, so now that solution needs to go into a stock pot with pieces of copper in it to retrieve the gold that was left behind
I thought the instructions said to use activated charcoal to precipitate the gold or precious metals,, then you just rinse it with water and melt....that way it saves from adding other unwanted metals... and cuts down on your liquid waste...I mean getting your precious metals and cutting down on waste is the entire reason for using Gold X ,, right
I suspect it's only the area around the silicon that has any gold plating, none really in the fiber. I am stockpiling this kind of waste and have decided to save some bottoms, but i am cutting most of the edges off (and therefore most of the solder) with tin snips (7 seconds per) or a bench shear (3 seconds) I just now went and prepared a 50g batch of BGA bottoms, removing 32g of fiberglass and solder- leaving 18g bottom centers.. So cutting the edges off reduces the material down to about 1/3. Thanks for further developing and sharing your techniques, B! I wonder if this tech will work on the internal parts of a camera module. Tiny, but I break down and save those too. If you can get the opportunity to refine camera guts, please do, I'm so curious and not yet a chemical refiner myself.
Awesome video. If you wouldn’t mind on your next one would you film what you yourself is doing as well. It’s great to see the reactions but I the type who enjoys to see the process in its entirety. Thnx again for the demo 🥂
Basically this is just cyanide leaching, using ferrocyanide apparently. That’s why you need to control the PH so hydrogen cyanide gas doesn’t get released and poison you.
Tak tento produkt mňa viac a viac presvieča. Ďakujem za to aj za skvele video. Inak urea in hot solution mňa pobavila (ty vieš prečo :-) ), ale ešte raz vďaka za info.
Ok,, so my earlier comment was before I watched the entire video,,, so here’s the proper method,, first , give the chips a HLC bath on a slightly warm hot plate to remove all solder,, you will know when it’s done, when it stops bubbling but the acid will still react with a VERY small pinch (a few grains) of baking soda,, then you remove ( pour off) all HLC for reuse,, second wash,wash,wash with water until a test strip reads neutral (7)... now your ready for GOLD X solution,, do it the same as you did before,, but this time DONT USE ZINC,, you contaminate your precious metals when you use zinc,,, USE activated charcoal,,, when the charcoal is done you wash it with water a couple of times then melt,,, it’s a lot easier than your first approach,, and the solution in the video most likely still has PM’s in it,, you used way too much Nitric Acid ,, that’s why you didn’t have a immediate drop of gold when you added SMB,, so now that solution needs to go into a stock pot with pieces of copper in it to retrieve the gold that was left behind
Where can I get this product from?
Hi bro, google + eco goldex agent ;-)
@Xtreme Performance Yes, I wrote this in video.
Justo este material te iba a recomendar Romania GoldRecovery
@@KevinPalencia235 ademas de no encontrarlo aquí en UK creo que es como cianuro ......
@@romaniagoldrecovery. No, este método es simple pero más difícil de obtener, el método con sulfúrico, nítrico y agua regía es mas accesible para ti.
I thought the instructions said to use activated charcoal to precipitate the gold or precious metals,, then you just rinse it with water and melt....that way it saves from adding other unwanted metals... and cuts down on your liquid waste...I mean getting your precious metals and cutting down on waste is the entire reason for using Gold X ,, right
I suspect it's only the area around the silicon that has any gold plating, none really in the fiber. I am stockpiling this kind of waste and have decided to save some bottoms, but i am cutting most of the edges off (and therefore most of the solder) with tin snips (7 seconds per) or a bench shear (3 seconds)
I just now went and prepared a 50g batch of BGA bottoms, removing 32g of fiberglass and solder- leaving 18g bottom centers.. So cutting the edges off reduces the material down to about 1/3.
Thanks for further developing and sharing your techniques, B! I wonder if this tech will work on the internal parts of a camera module. Tiny, but I break down and save those too. If you can get the opportunity to refine camera guts, please do, I'm so curious and not yet a chemical refiner myself.
If I get the material, I try it :) But the cameras would go through AR ...
Awesome video. If you wouldn’t mind on your next one would you film what you yourself is doing as well. It’s great to see the reactions but I the type who enjoys to see the process in its entirety. Thnx again for the demo 🥂
Good work and this is the best way to deal with BGA tin and tin-in-department work
I have to give it try
Great, the more us, the better we learn :)
How would deal with the Solder balls if you didnt have Eco Goldex? HCL. Nitric acid and citric acid. Or another way I dont know of?
HCL
What's the problem with cyniade stripping? It is very cheap and effective if used in a proper manner
Basically this is just cyanide leaching, using ferrocyanide apparently. That’s why you need to control the PH so hydrogen cyanide gas doesn’t get released and poison you.
I remove the solder first with HCL. After rinsing with hot water several times, then process the bottoms as you do.
Solder remover is better way
Tak tento produkt mňa viac a viac presvieča. Ďakujem za to aj za skvele video. Inak urea in hot solution mňa pobavila (ty vieš prečo :-) ), ale ešte raz vďaka za info.
Díky. Ono to ve videu vypadá jednodušší, než to v reálu je :)
@@BohumilGraman To už som zistil na vlastnej koži pri veľkych stratach ked som si myslel: videl som videa a už to viem :-)
What is the chemical solution? For inicial thank
very good the video !!!! congratulations!!!!
Now what's the name of this product? You can talk ?
Eco Goldex
Wouldn't it be just as effective to treat it like ram sticks?
So I'm not sure ...
Eco friendly cianid?????
why cant smb be used in this recovery?
Because this solution is not AR.
There are gold under green fiber
Была бы возможность ставить русским титры, было бы супер 👍👌🤑
Я не очень хорошо пишу по-русски, но если хочешь, можешь :)
Bohumil Graman 1
Recuerda a la personas usar guantes y máscaras y un lugar con buena ventilación ☢️☠️
hello a hcl what percentage
35
@@BohumilGraman hello can ph be adjusted with 20 percent hcl? After adjusting the pH do you filter?
@@szabolcsbalogh7120 yes/yes :)
Thanks. you would enter an email address?
Silver jsi neřešil? Spodek desky obsahuje Tin a Silver. Jen mě to zajímá. Přece jenom je to už 5 let a člověk se učí neustále.
Neřešil, ale až to budu dělat příště, zkusím to ;-)
thank you
I will stick to nictric, its way less work and better.
Need to get rid of soldier first
yes
I can hear ur clock... :)
YES! :-D
Excelente.
thx
This item gold average per kg .750mg okay my daily work dear respect from Pakistan 🇵🇰
👍
Thumbs Up
Thanks
Lousy video...
Teach people the correct methods !
1) Teaching also includes demonstration of alternative methods.
2) I don't want to teach anyone :-)
3) Lousy video? And where is yours?