How to replace condenser on 2010 Mazda 3 part2

แชร์
ฝัง
  • เผยแพร่เมื่อ 30 ม.ค. 2025

ความคิดเห็น • 32

  • @tastyratz
    @tastyratz 3 ปีที่แล้ว +6

    Doubly triply extra work. I took my condenser out from the TOP and I didn't even remove the radiator to do it. Pull the bumper and headlights. Unbolt the side framerail bolts. You can access the clips holding the condenser to the radiator from the front. Unclip the 2, lift the top latches for the radiator, and disconnect the high and low lines. Then just pivot the radiator forward and it BARELY slips up through the top. Might need to shift the harness and lines around (still have to unplug the front pieces).
    Done, easy. Don't forget to realign your headlights after.

  • @coolcool4833
    @coolcool4833 2 ปีที่แล้ว +1

    THANKS FOR EXPLAINED 👌 👍 BEST

  • @MakeItMike
    @MakeItMike 3 ปีที่แล้ว

    I'm very happy to read that some people did this pulling the assembly from the bottom. I need to put in a aftermarket radiator and might as well do the condenser as well. All the fins at the bottom are bent in and making the car run hot. I have a 2011 Mazda 3 with the 2.5. anyone who can chime in would be appreciated.

  • @danieleliaskhodirbrinch1009
    @danieleliaskhodirbrinch1009 7 ปีที่แล้ว

    Just so you/and others that might counter this knows; the tiny line is the high pressure, the big line is low pressure. It even says "L" on the cap of the clutch on the low pressure line :)

  • @valetudo1976
    @valetudo1976 2 ปีที่แล้ว +1

    Came here to see how to take off the radiator support itself. FYI. If you don't have to replace a condenser or the radiator itself, the support CAN be removed without disconnecting them!

    • @gavrilovas1
      @gavrilovas1  2 ปีที่แล้ว +1

      Well this video demonstrated on how to replace all front just in case... ;-)

  • @spitstickler
    @spitstickler 7 ปีที่แล้ว +2

    What a pain! How long did it take you from start to finish?

  • @samieusufzai5079
    @samieusufzai5079 6 ปีที่แล้ว +4

    You can dismount the radiator and condenser from the bottom without doing all of that

    • @gavrilovas1
      @gavrilovas1  6 ปีที่แล้ว

      no, you can not.

    • @aceriva2261
      @aceriva2261 6 ปีที่แล้ว +3

      You can absolutely remove this a/c condenser from the bottom of the car without removing hood metal bumper, lights, etc and it only takes 2 hours. I'm doing a 2011 mazda 3 now.

    • @GeorgeBabiy
      @GeorgeBabiy 5 ปีที่แล้ว +1

      Ok so a month ago I have changed my condenser, all work great now. And to confirm YES you do have to follow step by step what guys are showing in the video to achieve the result. And allow yourself 6-8 hours and a good day with a good weather. Good luck guys. 👍

    • @stivan5526
      @stivan5526 5 ปีที่แล้ว

      Ace Riva do u have any video.?

    • @ericbeaulieu4663
      @ericbeaulieu4663 4 ปีที่แล้ว

      @George Babiy 6-8 hrs lol, i wish you joking. It tooks 2h30 at dealership to remove, refill ac and coolant and put bumper back.

  • @gavrilovas1
    @gavrilovas1  12 ปีที่แล้ว

    ;-) do you have some?

  • @ericbeaulieu4663
    @ericbeaulieu4663 4 ปีที่แล้ว

    Just to let u know that your old condensor was for a sedan car and you put a hatch model. Those are not the same part, different dryer locations, you may had some a/c issues.

  • @Sazonman
    @Sazonman 5 ปีที่แล้ว +2

    Gotttt dammmm that's alot of work to replace a condencer on mazda 3

    • @gavrilovas1
      @gavrilovas1  5 ปีที่แล้ว +1

      well some people say it could be done under the vehicle without removing front bumber!

  • @iggytv7849
    @iggytv7849 ปีที่แล้ว

    I think you can pull out the fan, radiator, and condenser from there bottom without removing all these assembly. The bumper, headlights and the fiber assembly didn't need removal...

  • @totokingkong1
    @totokingkong1 8 หลายเดือนก่อน +1

    It's not an ac filter it's a dryer

    • @gavrilovas1
      @gavrilovas1  6 หลายเดือนก่อน

      Thank you for your comment.

  • @amr-50
    @amr-50 6 ปีที่แล้ว +1

    Wrong procedures you have to read the instructions then you gonna find easier way than dismantling the whole car

    • @Bluefall
      @Bluefall 5 ปีที่แล้ว

      Yea... thought the same... no need to dismantle the whole front end...

  • @igorvorobjov
    @igorvorobjov 3 ปีที่แล้ว

    You forgot to remove the fenders...

  • @MrLew1965
    @MrLew1965 7 ปีที่แล้ว

    WHAT A PAIN IN THE ASS !!!

    • @gavrilovas1
      @gavrilovas1  7 ปีที่แล้ว

      it's a long labor, yes I know.

  • @leothelion634
    @leothelion634 12 ปีที่แล้ว

    nobody has any arm hair

    • @MB-sp6sp
      @MB-sp6sp 5 ปีที่แล้ว

      Modern world.... shaved

  • @sarinsarin7898
    @sarinsarin7898 2 หลายเดือนก่อน

    All this bs is not necessary.