Brilliant. Thanks. Saved me buying a new machine - disassembled to clear a blockage. Wouldn’t have been confident enough to force some of the panels without your guidance.
do you perhaps know how to dissasemblle a GRAN LATTISSIMA? Its got no screws or anything so I assume its clips but so risky I might end up breaking it all off.
Great video, thanks a lot! FWIW my front cover unsnaps from the bottom front, not the top back as you appeared to do. I am impressed with the machine, reasonably easy to work on!
Thanks, I’ve got the EN550.W updated and slightly different to this, main difference in disassembly is the clip on thePCB which is much harder to remove as it has two tiny brown plastic clips holding it on. Sadly my extraction head is leading from with in, it was actually very clean. The extraction head replacement, hard to get and seem to out of stock everywhere.
Thanks I bought a replacement extractor, and the hardest part of the job was getting the spout of the front of the old unit. I then found it was filthy with sticky coffee residue, which was probably the cause of the leak. The other hard part was inserting the tube, but a little bit of dilute washing up liquid, on the tip, provided just enough lubrication to enable me to click it back in place. It was really helpful to be made aware of the screw inside! Thanks
Disconnect the hose in the other end located at the side of the machine, and pull it out together with the extractor. It is then MUCH easier to get the clip back later on. And as someone wrote, use something small like a paper clip to push it down when putting the clip back.
Thank you Mike! Your video helped me a lot! I discovered that the nozzle was obstructed with dreg coffee! Now is working perfectly!! Tks I from Brazil!!!👏🏾👏🏾
Thx for the video. Saved our machine last time. Now we replaced the extractor head again because we had water leaking in the bottom container. But the problem is not solved this time. Does anyone have a suggestion? It seams that the coffee making process is slower as if the machine struggles to pump water through the coffee capsule and sends some of the water down to the bottom container. Thx in advance! Best regards Mia
Whatever you do, do not remove the plug with pliers like that the plug actually has tabs on each side that hold it in place. If you grab it with pliers you will rip the mount off of the board. This is why people are commenting “how do I put the plug back”.
thanks Michael. your video really helped i was able to replace the extractor head and now working again with no leak. a little tip when putting in the white pipe into new assembly you can use a small screwdriver to help it push in. Couldn't have fixed my machine without this video
This is a great video on how to break your machine. How many times he says “I think” and “should” ...SHOULD be warning one. Luckily I have a second machine, but this ones plug is now ruined. Just pull it out with your fingers indeed. Smh
Thanks Michael for the video. I have read all the comments and I am now going to attempt this repair as mine is leaking water from the top badly and thorough multiple cleanings has the filter head area very clean and free flowing but still leaks out the top. I see ppl having these 3 issues: 1. Snapping off the electrical connector from the board 2. Removing the filter head 3. Ordering the part 2 and 3 I think are doable but 1 is concerning. Can you do the repair and leave the cable connected, or can you disconnect it more carefully as to no break off the connector from the board? Thanks!
Follow-up: I ordered part from buyspares.co.uk and did the repair. I avoided the electrical issues by not disconnecting the cable and instead swinging the top over to the side and taping it in place to stabilize it while I replaced the extraction head. Only issue was the “Coffee Outlet” plastic part does have to be snapped off in order to do this. With a little patience and a pair of small flat blade screwdrivers it can be pried off. It’s pretty strong. If you’re worried, order a spare, it’s only 3 bucks. It has a lip at the bottom that you have to bend the whole thing forward to pull it up and out (and reverse on reassembly). Overall, easy job that took about 30 minutes going slowly. One, last note, once all put back, the whole thing did NOT work. Unfortunately, I needed to descale so I had an orange light and two white lights but no buttons worked. Even with the descale pipe, no buttons worked. Research showed it may be that it needs to be primed. However, with a strong small magnet I was able to move it around the descale pipe entry area and trigger some discharge activity. Worked with it for a long time and gave up leaving it full of water plugged in all night. Today, everything is fine! Descaled and made a delicious latte. I’ve had the steam side modded to be a steam wand for a couple years now and that’s been the best thing ever. (Details if someone is interested).
Witam. Wypięcie tej taśmy od panelu sterującego na tym filmie jest przeprowadzone błędnie. Facet wyrwał z płytki cale gniazdo teraz będzie musiał je przylutować to wielki błąd. Wystarczyło delikatnym płaskim śrubokrętem wypiąć wtyczkę z gniazda to się dzieje w 3 minucie filmu. Nie róbcie tego tak bo będziecie mieli problemy. Pozdrawiam
Fabulous and thank you, 2020 and still relevant. eBay $69Aud - Part Number:7313244971. Just replaced my infuser piston thanks to this video, many thanks.
Michael, Thanks for great video, can you help me re locate the item 37 called renforcement, I cant find a place for it It came off from somewhere when I removed the assembly thanks Philip
Read the comments below before attempting. At 3:28 he removes a plug from the control board but the holder to the pcb board comes away with it (cannot seperate). You cannot just re-fix the plug then. It needs someone to re-solder the holder to the electrical board. Wish I had read the same comments before buying a new extractor head !
Didn't like This. It takes you up the garden path and drops you at the gate.I need to take the filter head off. You don't do this, instead you poke at it with a screwdriver and then say 'End of video'. Then you tell everyone that the hose was the most difficult, but you don't show it
Hi. I detached it as you instructed. But when I tried to put pieces back I did not succeed. That electrical component that was detached using needle nose pliers was not fixed back in the place. What should I do to put it back properly?
At 3:33 where you rip out the ‘only piece of electronic gear’ from the pcb - we ave encountered an error perhaps in your instructions that does not allow us to re fix that singular cable to the back of the machine - please explain why?
Hey you need to reshoot this or add instructions on removing the plug I am plugged it in the horse soldered piece came off you need to be very careful as to how you pry it off to leave the bracket on the board now I have to get a soldering iron
Thanks for taking the trouble to make this video. We were originally looking at replacing the machine but after watching this, I also replaced the extractor head and our machine is working fine again.
Hi guys! I have the same machine and sometimes I recieve a message saying "System Empty Repeat Delivery".I have this issue almost everyday and I can't make the coffe when I get this message in the screen.Any suggestions?
Anyone know where to get the rubber part (gasket) separately? All diagrams and sources online point to an o-ring, which it isn't - you can see in the video that it's a cylindrical object - Michael has it in his hand at 6:14 and talks about how the new kit came with a new seal - I don't need the kit - I just need the seal - mine is cracked. Tried to improvise with 2 SAECO o-rings - made things worse.
Thank you so much, replaced extraction head following your tutorial. Got stuck on inserting the hose, then just made a thin stick from the Chinese bamboo chopstick and pushed with it that metal thing (on the end of the hose) deeper into the position. Done!
Hi Michael, I’m in safety Bay, my latissima is leaking water out of the top, is this the reason you have replaced the extraction head? I got part of the way through the dismantle with your video to help me and realised that I may have to replace the entire head too. I figured there may just be a loose or misaligned seal, but I can’t see one. Where did you purchase the part?
Brilliant. Thanks. Saved me buying a new machine - disassembled to clear a blockage. Wouldn’t have been confident enough to force some of the panels without your guidance.
do you perhaps know how to dissasemblle a GRAN LATTISSIMA? Its got no screws or anything so I assume its clips but so risky I might end up breaking it all off.
Great video, thanks a lot! FWIW my front cover unsnaps from the bottom front, not the top back as you appeared to do. I am impressed with the machine, reasonably easy to work on!
How do you get the clip back on ours won't hold and now we have a machine that won't power up.
Hello, thanks for this good explanation, I'm curious where you got the rubber van. Can you give me the address? Thanks in advance. Jaap
Thanks, I’ve got the EN550.W updated and slightly different to this, main difference in disassembly is the clip on thePCB which is much harder to remove as it has two tiny brown plastic clips holding it on. Sadly my extraction head is leading from with in, it was actually very clean. The extraction head replacement, hard to get and seem to out of stock everywhere.
This guy's very good. I like his style.
Clear video, nice explanations, really appreciated. Great job!
Thanks I bought a replacement extractor, and the hardest part of the job was getting the spout of the front of the old unit. I then found it was filthy with sticky coffee residue, which was probably the cause of the leak. The other hard part was inserting the tube, but a little bit of dilute washing up liquid, on the tip, provided just enough lubrication to enable me to click it back in place. It was really helpful to be made aware of the screw inside! Thanks
Disconnect the hose in the other end located at the side of the machine, and pull it out together with the extractor. It is then MUCH easier to get the clip back later on. And as someone wrote, use something small like a paper clip to push it down when putting the clip back.
Thank you - this was a great guide!
How did you get the little silver hook on water pipe, I’ve been trying for 3 days, thanking you so much
Minha máquina latissima não sai leite, alguém pude me ajudar????
Thank you Mike! Your video helped me a lot! I discovered that the nozzle was obstructed with dreg coffee! Now is working perfectly!! Tks I from Brazil!!!👏🏾👏🏾
Don’t do this!! At 3:25 if you pull the white plug you snap the solders and render it useless.
Thx for the video. Saved our machine last time. Now we replaced the extractor head again because we had water leaking in the bottom container. But the problem is not solved this time. Does anyone have a suggestion? It seams that the coffee making process is slower as if the machine struggles to pump water through the coffee capsule and sends some of the water down to the bottom container. Thx in advance! Best regards Mia
Whatever you do, do not remove the plug with pliers like that the plug actually has tabs on each side that hold it in place. If you grab it with pliers you will rip the mount off of the board. This is why people are commenting “how do I put the plug back”.
Good video, thanks !
thanks Michael. your video really helped i was able to replace the extractor head and now working again with no leak. a little tip when putting in the white pipe into new assembly you can use a small screwdriver to help it push in. Couldn't have fixed my machine without this video
how do you take off the housing at the front of the extraction head?
gently use a screwdriver and loosen then pull off.
This is a great video on how to break your machine. How many times he says “I think” and “should” ...SHOULD be warning one. Luckily I have a second machine, but this ones plug is now ruined. Just pull it out with your fingers indeed. Smh
nah he was really good i have to say politely disagree. he really helped me
Thanks Michael for the video. I have read all the comments and I am now going to attempt this repair as mine is leaking water from the top badly and thorough multiple cleanings has the filter head area very clean and free flowing but still leaks out the top. I see ppl having these 3 issues: 1. Snapping off the electrical connector from the board 2. Removing the filter head 3. Ordering the part 2 and 3 I think are doable but 1 is concerning. Can you do the repair and leave the cable connected, or can you disconnect it more carefully as to no break off the connector from the board? Thanks!
Follow-up: I ordered part from buyspares.co.uk and did the repair. I avoided the electrical issues by not disconnecting the cable and instead swinging the top over to the side and taping it in place to stabilize it while I replaced the extraction head. Only issue was the “Coffee Outlet” plastic part does have to be snapped off in order to do this. With a little patience and a pair of small flat blade screwdrivers it can be pried off. It’s pretty strong. If you’re worried, order a spare, it’s only 3 bucks. It has a lip at the bottom that you have to bend the whole thing forward to pull it up and out (and reverse on reassembly). Overall, easy job that took about 30 minutes going slowly. One, last note, once all put back, the whole thing did NOT work. Unfortunately, I needed to descale so I had an orange light and two white lights but no buttons worked. Even with the descale pipe, no buttons worked. Research showed it may be that it needs to be primed. However, with a strong small magnet I was able to move it around the descale pipe entry area and trigger some discharge activity. Worked with it for a long time and gave up leaving it full of water plugged in all night. Today, everything is fine! Descaled and made a delicious latte. I’ve had the steam side modded to be a steam wand for a couple years now and that’s been the best thing ever. (Details if someone is interested).
Witam. Wypięcie tej taśmy od panelu sterującego na tym filmie jest przeprowadzone błędnie. Facet wyrwał z płytki cale gniazdo teraz będzie musiał je przylutować to wielki błąd. Wystarczyło delikatnym płaskim śrubokrętem wypiąć wtyczkę z gniazda to się dzieje w 3 minucie filmu. Nie róbcie tego tak bo będziecie mieli problemy. Pozdrawiam
It‘s perfekt ... but i want more
Thnx. Very usefull
Fabulous and thank you, 2020 and still relevant. eBay $69Aud - Part Number:7313244971. Just replaced my infuser piston thanks to this video, many thanks.
Just made my first good cup of Nespresso coffee in 2 years thanks to this video! ❤❤❤
Michael, Thanks for great video, can you help me re locate the item 37 called renforcement, I cant find a place for it It came off from somewhere when I removed the assembly thanks Philip
Read the comments below before attempting. At 3:28 he removes a plug from the control board but the holder to the pcb board comes away with it (cannot seperate). You cannot just re-fix the plug then. It needs someone to re-solder the holder to the electrical board. Wish I had read the same comments before buying a new extractor head !
Thank you. The problem with my machine was the O ring, a bit of grease and it is working again.
Hi, how do i reconnect the electrical plug. I am unable to reassemble it back before the plug doesnt connect anymore
Didn't like This. It takes you up the garden path and drops you at the gate.I need to take the filter head off. You don't do this, instead you poke at it with a screwdriver and then say 'End of video'. Then you tell everyone that the hose was the most difficult, but you don't show it
any joy figuring out how to get that filter head off
Hi. I detached it as you instructed. But when I tried to put pieces back I did not succeed. That electrical component that was detached using needle nose pliers was not fixed back in the place. What should I do to put it back properly?
I got it working after i resolder it back. U need to remove plug from the base and solder it.
@@miloice74 Do you have to take the board out?
@@ThanhTran-jj3vd no i didn't
@@miloice74 how do you resolder it, the pins are so tiny?
@@ThanhTran-jj3vd i used a magnifying glass, it was very difficult indeed.
At 3:33 where you rip out the ‘only piece of electronic gear’ from the pcb - we ave encountered an error perhaps in your instructions that does not allow us to re fix that singular cable to the back of the machine - please explain why?
Perhaps you have it upsitedown? Happend to me to. Goor luck
@Saskia Hemmer I can't get the ribbon cable back onto the board. I'd love to see how MIchael was able to do it.
Hey you need to reshoot this or add instructions on removing the plug I am plugged it in the horse soldered piece came off you need to be very careful as to how you pry it off to leave the bracket on the board now I have to get a soldering iron
Thanks to your video I was able to remove my extractor head and put it in my dishwasher. super clean, no more leaks. And cost €0 :)
Fremantle in Perth? Shame, Michael! (Shall accept your informative video as repentance)
Thank you Mike. Exactly what I needed. Great work. Best regards from Spain
Thanks for taking the trouble to make this video. We were originally looking at replacing the machine but after watching this, I also replaced the extractor head and our machine is working fine again.
HI, can you tell me part number of the extraction head or it is the only one on delongui latissimi? thanks, good job
perfect, made my day!!
Thank you a lot.. It helped as well.. :)
Hi guys! I have the same machine and sometimes I recieve a message saying "System Empty Repeat Delivery".I have this issue almost everyday and I can't make the coffe when I get this message in the screen.Any suggestions?
This video helped me fixing my machine. Thank you and greetings from Israel!
Anyone know where to get the rubber part (gasket) separately? All diagrams and sources online point to an o-ring, which it isn't - you can see in the video that it's a cylindrical object - Michael has it in his hand at 6:14 and talks about how the new kit came with a new seal - I don't need the kit - I just need the seal - mine is cracked. Tried to improvise with 2 SAECO o-rings - made things worse.
Thank you so much, replaced extraction head following your tutorial. Got stuck on inserting the hose, then just made a thin stick from the Chinese bamboo chopstick and pushed with it that metal thing (on the end of the hose) deeper into the position. Done!
Where did you purchase replacement part?
Thanks, that was very helpful. Coffee machine is working again 😃! Cheers from the other side of the world ☕️🇨🇭.
Alexandra Studer where did you purchase replacement part?
hey! first off thanks for the video! was your problem what they call an electrical problem?
Hello, how did you put back the plug after fixing the machine ? It looks like it needs a welding no ?
I had to superglue mine back, as the lugs didn’t hold. It’s not made to be taken off.
Hi Michael, I’m in safety Bay, my latissima is leaking water out of the top, is this the reason you have replaced the extraction head? I got part of the way through the dismantle with your video to help me and realised that I may have to replace the entire head too. I figured there may just be a loose or misaligned seal, but I can’t see one. Where did you purchase the part?