วีดีโอ

Thanks, I’ll have to use it myself if I got one again 😊

Matebox in Motion jeg lægger nogle billeder op i inav fixed wing group på facebook. Senere i dag.

har netop lagt billeder op i gruppen. Det må betyde mere vægt at vingerne kan tages af?

@@vovsen123 nej, heldigvis ikke noget msn kan lægge mærke til. Jeg har skubbet et karbon-rør ind i vingerne så de ikke tager skade af at hive dem ud igen. Det er næsten alt! Og så lidt krids-krads i ving spidserne så de ikke løsner sig.

AZ Drone Dude if you are missing the middle wire because you have an early T16 in the battery pack, then it might be hot. It’s though getting hot when charging but not very hot, that’s why it’s a good idea to place it so air can flow free around it.

Yes of course, else I won’t have published it. And you can see the LED through the hole for the jack connector. When it’s lit then it’s charging.

@@StavrosKor yes there is plenty of space inside it, but by placing it under the internal transmitter module I avoid to change wires to place it elsewhere.

Tomáš Konkoľ thanks, you’re welcome.

Yeah, I was arguing with myself wether to fly or not, but it was a long trip from the car to the airfield so not to waste it, I fly and it went well.

Thanks, happy you could use it

I can get the Inductrix to almost bind.. the front two LEDs start flashing white, the rear two are red while the back "taillight" is green. It seems as if it would be bound, except only half of the LEDs are solid. I am using an OrangeRX module in my Taranis. One thing that's weird is, my only option for channels is 1-8 on DSM2 DSMX.. any ideas? thx

I have have used a Spektrum Sender Module and don’t know the Orange module.

ivan moraga I’m sorry but i don’t understand your language.

Villy Feltmann hi, very good video, consult: with this connection method I can flash, load the firmware back to the FC?, and be able to do it, as would be the steps for the fc board to be recognized by the cleanflight and perform the flashing? thanks greetings !!

Pradeep J.B yes, it depends on the receiver. But it’s several years ago I did this video so thing may have changed since.

insomniac 56 The FTDI supply the Naze with 5v. On the interface there is a 5v pin so it’s just a matter of connecting 5v and ground to a output port on the naze

Aussie's Multicopter Adventures you have to have the channels in the TAER order. Else it will not work. I made the same mistake on the first Inductrix as Taranis' channel order is different as standard.

Thanks for your reply Villy. I discovered the problem by accident after watching many tutorials and reading many forum posts. Most of the info out there is how to use the Orange TX. I guess it's a lot cheaper than the DM9 module. Anyway, for others having the same issue here is what worked for me. How to bind Taranis Plus with Spektrum DM9 module to Tiny Whoop Set the frequency type to PPM instead of DSM2/X setting per @GenCode FPV in the comments bellow. I also had to bump up the PPM frame from 22.5ms/300- to 22.5ms/450+. It would bind but would not actually do anything. I also set the end point on my throttle, channel 1, to -86 instead of -100. Any lower (more negative) and the throttle has a large amount of nothing and any higher (closer to 0) and the motors don't shut off after landing and puling the stick to full down. I'M NOW WHOOPIN'! Cheers Aussie

Mr. Inabilidade which part are you missing information from?

GenCode FPV I have used a DX5e sender module to spektrofy my Taranis. The link is in text above

okay, thanks, guess thats why, but I got it working. Thanks for the reply.

You have to ask the manufacturer

Mit Hero2 jeg også bruger på mine quads

I don't have it anymore. Read the manual.

I have no experience with orange, except the fruit. Sorry.

Villy Feltmann lol,cool no probs, got my inductrix today, bound and flew with the t-six thanks anyway

it was a mere trail and error that lead me to the solution, and of cause reading the manual :-) for all Horizon/Blade fc use the control channel in the same order as I setup TAER for channel 1-4 and reverse channel 2. use channel 5 for flight modes and channel 6 as disarm/panic button

would love to do it in English too, which was my intention, but I lack the time :-( Prefer to use the time to fly :-)

The Flip32 and Naze Flight controllers have their Sbus inverted thus the need of an inverter cable.

Sorry, I don't have it anymore. It was of too cheap quality

Hehehe...