วีดีโอ

Looks great, paint it orange.

Didn't save 10k. You need trucks to haul it away and gotta pay to dump it.

My problem is I don’t have any of the tools so now what?

Very helpful, thank you!

Thanks for the breakdown. My air compressor just stopped working one day (no sound or reaction of any kind when trying to turn it on). Thought it might be a capacitor issue. Any advice (or maybe a future video?) for diagnosing start and run capacitors with simple DIY grade tools?

Really helpful I was at a loss trying to do mine. Thanks for the vid

What frustrates me, is the smashed down weeds via tires, that the brush hog now can't cut. ...next day, they're popped back up.

Hi, srry for my English but i have a question, where dou you buy the door rubbers? And whats the name of , i need of the right and left door , thank you and greetings from uruguay

Have to go buy an air compressor now ...

You can use a wet and dry vacuum from outside and suction out drain line

Vacuum it from outside

and I've been using scotchbright for years

Chinese concrete style

That’s a really good idea. Thank you

I can't believe how cold/dry those solder joints look directly from Bose! When I repair my headphones, I'm going to flood every joint with some leaded solder. I would have expected a broken wire from flexing...not a junk solder joint!

So after investing $1200 in welding, cutting equipment, and misc iron pieces, it's cheaper for most to buy the canopy... (great idea though)

Smart!

I keep a roll of tinfoil in my kit. Works great.👍

I just buy a pack of condoms.

They literally make caps for this application.

What's going to keep dirt from going inside the hose? When you pull that piece of rubber off you didn't clean the threads.

At least you only got paint in your hydraulic line.

Thats why my spareis in the bed,way easier access

Just twist it 180 bro n you can just go thru the space there

how’s everything going?,Unlimited. Like it~total well - ciao!📢

Did you just invent the washer?

Will use

I just installed a bunch of theese in a house that had the same issue, the electrician told me those tabs on each corner are scored to make it easy to bend them back and use as standoffs. This is a great idea tho!

Lol he is a plumber

That screwdriver lmao

Thanks! Are you planning on doing any more Dodge truck videos? I bought an 85 D150 around a month ago and need all the help I can get. This is definitely on the list of things to do.

Thanks for making this video. Super helpful as I am about to replace the vent window seals on my '78 D200. Here is a summary I wrote up while watching your video: • Order plastic door seal install tool • Take pictures of the position of the vent window pivot and anything else you need to remember • Take vent window bolt out and don't drop the glass or lose the plastic grommet • Remove door panel from door • Lower window all the way to get to front window liner seal • Remove plastic dust cover from inside of door and remember to re-apply later • Remove vent window seal from outside prying with screw driver to get behind vent seal and pop out • Remove screw that sits at front inner frame of the door - sits kinda in the middle, the inner frame can wiggle once this is loose • Very gently work front window liner and frame out through the top but be careful not to break window - it comes up on the inside of the door frame, there is one more bolt down low in the door. Guide the exit with one hand while removing with the other. • Once the assembly is out, there is a Philips screw that holds the vent window frame into the assembly, will need to remove this screw • Remember to orient the lower vent window pivot correctly from your picture • Put the vent seal into the frame working it in with the plastic guide tool and use soapy water to help alleviate friction • Remember to reinsert the pivot before reinserting the assembly into the door frame • Re-insert the small screw into the door frame to the top vent window pivot with blue loctite (per comments) • Re-insert glass •Guide the seal to the outside of the door frame and allow the lip to seal properly - soapy water is helpful to lubricate •Give the seal a good press/squeeze all around the make sure everything is seated

I mean yes but as a Kubota mechanic i can tell you that 90 that was blocking your wrench comes out easy after you disconnect the line and break its locking nut. I mean i like the creativity... and since you were only replacing the one your way is actually less work i give it a 10/10.

I make my own wrenches and tools all the time, it's called old school technology, you green horns call it think outside the box

You made a line wrench

Would have been quicker, easier, and cheaper to just remove that elbow in the way. They also make those wrenches, you can pickup a set at harbor freight

Looks like you might have been able to get it off with a crows foot.

You invented the line wrench! You should seek a patent for it.

Line wrench

Always carry a cheap set of wrenches

You need a weather head socket

Genius!

this guy is not a mechanic you could just undo the other end of the hose and slide your wrench down it lol

🤦🏾‍♂️🤦🏾‍♂️Use a crowsfoot

Boy howdy,you rocket heads are genius!!!!! Did you know that the 2 first upper and lower fittings have a jamb nut on them and all you have to do is simply just break them loose and rotate them out of your way!?!? .... slay on geniuses. Geez where do you people come from?

Was going to say, they make several different styles of flare nut wrenches. Specifically for tight spaces like that.

They're called flare wrenches if anyone needs one. They're great to have a set with any hardline connection.

Nice idea but you know they already make those off the shelf. But if you’re pinch that’s an awesome idea!!

Save it for the 4th of July and light it in a stand to kick off the party!!

Cut fuel line at a heavy angle, poke a very small hole near the end, insert a parts tag wire through and twist. Put wire through hole spray hose with lubricant and pull gently. That's my plan.