วีดีโอ

Is it ok not to connect the upstream o2 sensor? What does it do? Thank you

Can u remove without wrenched

!!!!! Use the BLUE fluid that's designed for your Honda, NOT green. Don't use water from a hose, use a flush or a mix of distilled water and vinegar to clean, then flush and fill with the blue.

You are awesome man thanks a lot to explaining it step by step. Jagjit singh khalsa❤

Tell the metric /standard size tools that you use while doing the job. It gives more detail. Good vid though. I liked it.

Super great description. Easy to follow and imitate.

y(^O^)y南無阿彌陀佛爸>NamoAmitabha88>南无阿弥陀佛爸>ナモ阿弥陀お父さん y(^O^)y

Screw driver probably would've been cheaper

Do you still have this car? If so, how is the Peak coolant holding up?

Thanks for the video man!

He didn't even look at the upper slide pin let alone service it. Do not forget this step.

Can use use red coolant on this car

Found this video just in time for my break pads to be changed lol 😂 thank you 🙏

VERY informative. Thank you, Justin.

Good video Bro!

So what your gonna do is.... then it should be removed. As you can see I put new o rings on... WHAT?!

TORQUE SPECS FROM MAZDA ... 9 lbf for the filter cover drain plug and 22 to 25.8 lbf for the plastic oil filter cover ...I BOUGHT ONE NEW IN 2008 ... the specs are identical to for all the 2.3 IL4 .... you do not know what you are talking about and nobody should take you for an example .

Can you make a video replacing the cabin air filter please?

The groove on mine is way too tight and I can’t move it. What do I do?

Use your old oil with 50% diesel mix and you have the best wood stain for your fence or deck and it protects against termites 👍

You should show us if the code is gone.

We have exactly the same car except for the color. Where is your condenser and fan? Was it the cause of having your oxygen sensor broken?

Hey just had a question. I have a 97 Honda Accord and does the block heater connector go on the radiator drain valve? Is this right? Because I read it it another thread.

U dont have to turn on the heater, you just turn the switch to hot, making it actually blow doesnt change anything

Thank you for this ! Truly honestly 💯

What do you do if where you change the oil filter is stripped ?

LMFAO, YOU CAN'T PRIME THE OIL BY TURNING THEY KEY ON & OFF, THE FUEL PUMP YES BUT NOT THE OIL PUMP. IF YOU WANT TO HELP GET THE ENGINE OIL A BIT FASTER FILL YOUR FILTER UP WITH AS MUCH OIL AS POSSIBLE BEFORE INSTALLING IT, BE VERY FAST IF DOING IT ON YOUR CAR SINCE IT SITS SIDEWAYS. THE FILTER WILL SOAK IN QUITE A BIT OF OIL IF YOU FILL IT FIRST & THEN START YOUR OIL CHANGE, THEN ADD A BIT MORE.

Thanks

Great video! Thanks dude.

Can you remove the caliper bolt without that long breaker bar. Short ratchet i couldn't even budge those bolts.

Am I lost or did he only hand tighten the drain plug? I just got an oil change at Valvoline and they said I had an oversized drain plug and could only torque it to 15ft lbs. Was trying to figure out what torque settings you used here.. Just got the oil changed so it's tedious to get my catch pan fixed with a tap set cause I'm pretty sure they won't reuse the new oil coming out of it and charge me for an oil change again.

Queases cuando el termo está tapado

I recently just took my car to the mechanic to fix problem. Poor shoddy work and the worse of all was that they forgot to put the under carriage splash guard back up. Two weeks later ... while checking the work on car I realised the splash guard was missing. I immediately drove back to the mechanic shop to tell them my splash guard was missing.... after some mean words. they let me go at the back in the work area and lord and behold... there was my splash guard sitting on top of tyres being used as a tray by other mechanics to put their work tools on top ... needless to say ... I am not going back there ...

Nice video dude! Keep posting more!!

Omg...did any one notice the bottle had water droplets there....

So my sensor is stuck like it won't come off with anything!! Then the top of it the metal connector broke it just broke off and I don't have a socket to fit the top of it I even try to impact it won't come off PB blasters still won't come off what the hell do you use to get this off with?

Thanks for the video. Is there a spring to maintain the seal on the filter ? Where is it located (cap or upper part of housing) ?

Yea, but how do you remove the oil cap in the engine compartment. Mine will not budge.

Helpful, thanks. Now I know I don't need the other gasket or gasket maker.

Thank you - very detailed -

Yes indeed. Good job. Thanks

This video sucks.

5 years later and you saved my butt. Thanks for this video. Very informative and straight to the point. <3

😬

That hose u took off the very first one what is the name of that hose? Yours is fatter than mine.

Is the same for 2006 mazda 6 ?

Why is no one draining the block?

Where can i get that special socket?

I know this is old, but I would recommend to use MotorCraft by Ford for your filter and oil... with a synthetic blend my friend.

Not sure 5 min is long enough to heat the water in engine block for thermostat to open and flush