วีดีโอ

I connected light bar to high beam without add key. When on full beam start work light bar!

I have a T27 but it’s a red and black wire to the bulb (xenon) , not blue like yours.

nice

Thank you for showing you cast your propellant outside instead of indoors that can be dangerous... I'm talking with years of experience and making thousands of pounds of KNSB propellant. We never use Fe2O3 or any type of surfactants and seem to get pretty good results with just KNO3 and sorbitol.

What's type of phone are you using are you using sir

Super impressive work sir

Start using PVC Schedule 40 for the case and nozzle, a coupler, and an end cap! And use PVC glue to join them together! 😁👍👍🇺🇸 Oooooo, and use 60 SU, 35 KN03, and 5 Karo Syrup! 😁👍👍🇺🇸

a better method is : hcl + pgm = pgm-cl , h2o-pgm-cl + naoh = h2o-pgm-nacl . the pgm percipates, just filter the excess solution

Instead of ammonium chloride You can use sodium hydro oxide "NaOH" to percipate PGM metals. But remember "Na" sodium is too a metal it will be mixed into platinum. So its better to use ammonia chloride cuz its a gas, when heated it will leave the beaker.

Aste sunt jucarii,oricum👍

Excellent video, a little to fast. A little more explanation re capacitor

in AR chlorine gas is released, would this gas precipitate Palladium in the solution with the Gold?

You summarized everything in PGMs refining world in one short video, really impressed, thanks a lot for sharing those information and hope you make more videos like this

does fe3o2 must be used?

Dont evaporate aluminum solution diluted

Please share your thoughts on the product now, a year after you created this video. Thanks

Annoying dog

Just winging it

When using fiberglass casings, you should always include an inner liner like Aluminum for better thermal reflection and absorption instead of into the fiberglass. Your case will last longer and keep the nozzle in place.

All of these are turds

That would blow up always check the voltage if it said 350v

at 0:55, that looked a lot more like 5-10cc of glycerin than 1cc. A full insulin syringe is 1cc. A full pinky sized syringe is 5cc. A full thumb sized syringe is ~10cc Also, you cannot trust your readings unless the scale is center loaded.

Please I was hoping to ask if I can use liquid sorbitol instead of the powder. The liquid is all I can find here.

You must stirr strongly the solution when you add the DMG.

I've got it set a bit higher. Or else the super bright spot on the road i front of the car will blind you.

What was the reason of white smoke?

i need❤

Refining rare metals, palladium platinum rhodium, I have large equipment professional refining

I need a lot of waste ternary catalysis

Did u check the weight?

How many newtons of power did you generate on the first fuel?

I'm sorry, but I believe that the exposure for the HID was turned down a lot, the red light and glow at around 2:50 is far from the same, if the exposure was locked on the same iso for both recordings, then all other lighting except for the car lights should have been the same. So either you are benifiting the led by over exposing it and making it look much brighter, which I think is the case as it looks over saturated with light, or the HID recording is turned down to make the LED present brighter?

Hid’s suk

Omg unsubcribing dude i thought you knew what you were doing

You got lead in it now is what the white crystals are bro

You have to much trouble bro its easy

What a mess😮

The hard part would be seperating the 3 metals after you got all the metal out. I always wondered if you can freeze it out, some metals and things will react when having it frozen out, but to do that the catalytic material would need to be ground up into powder which should have been done here too IMO

Use copper to get it to stick to the copper sand, or another sand with similar melting temps

Leeching is the most important part!!! It does take time, the longer you ket it soak the more you'll get!!!

I recently found out that Sodium Laureth Sulfate is a far better surfactant for sugar fuels than glycerin, it only takes .1% to .3% to make your KNSB as runny as heavy cream, you should give it a shot. I got 4 ounces of 70% SLS solution in water from ebay for $25, it should last me a decade at least, it only takes a drop or two per rocket, if that depending on the size. It does slow down the cure time though, it takes another half day to a day to fully cure so you can't launch your rocket the same day you make it.

good job

good job

you got 88 kg of trust

ρɾσɱσʂɱ 🙄

For the last test with the nozzle secured to the tube with bolts, how exactly did you reinforce the concrete with the bolts? Did you add bolts to the pvc casing straight through, then coat it with some thing to prevent the pvc from possibly melting? How exactly did you reinforce the concrete with bolts and how did that help? Sorry for the questions, I ordered some nice nozzles due to the clay stuff not cutting it anymore and just want to see how people are attaching nozzles to their nozzles

Ni(DMG)₂ forms a red precipitated in alkaline conditions. Probably isn't Rh

hello teacher, nice to greet you my name is vladimir I hope you are well I am a follower of your youtube channel I want to know if you can help me and guide me with technical advice I tell you I have material which is a stone that contains 7% rhodium analyzed by xrf portable and other metals where iron and quartz predominate, I want to know how to extract it from the sand that when grinding the stone leaves sand with rhodium particles which are seen with the naked eye as shiny silver, I hope you can guide me to extract rhodium from that sand and turn it into metal, I hope you answer me teacher, I will be very grateful, I hope you are well and thank you very much for reading me.

I think crushing it in a hammer followed by a ball mill would be better. Should enable the leaching and extraction process to go on faster. But there is a hazard with the dust which would be not healthy. So, both need to be near close loop so the dust stay inside. And you would have to wait for the dust to settle for each operation. Could be some other way but am not seeing it yet. But the filtered material should around 1mm max size.

Wow