- 12
- 12 560
Teck Tips
Canada
เข้าร่วมเมื่อ 29 ก.ย. 2011
วีดีโอ
Omron CPM1A Program recovery from death internal power supply
มุมมอง 4.7K3 ปีที่แล้ว
In this video I show you how to hook up CPM1A controller portion of the plc to a external power supply and give the correct signal so the plc actually run and communicate. Our company work in automation and find ways to save time and money to customer using creative mean like hardware hacking when needed. In this case no backup and no shematic were available on this machine, so, reverse enginee...
smart cdi booster, tuner chip from ebay
มุมมอง 9113 ปีที่แล้ว
Smart tuner kit, I found it very uneffective in my case. As I was searching arround the power problem, I ended up tuning the waste gate that was too tight and thus making restriction. even though this tuning chip show no spectacular gain and mess with the rail pressure, I can not say it won't at one point, make problem in the engine. I only can say it is best to tune and check the existing mate...
Smart CDI waste gate adjust
มุมมอง 6K3 ปีที่แล้ว
This video show how I ended up adjusting the turbo waste gate on smart CDI. you do this at your own risk.
Gapping rings and checking piston clearance JD650
มุมมอง 113 ปีที่แล้ว
In this part, I am checking the new rings and gappping them. Again, I am not an expert, you do this at you're own risk.
Johndeere yanmar engine 2T80 leak testing JD650 compression part 1
มุมมอง 563 ปีที่แล้ว
In this video I got a johndeere 650 that crank but does not start. it has overheated the previous year and water pump was replace. the block is crack, caused by rear implement that did not had proper support to front end. so oil level was not high enough. when engin was working there was a bottom end knock. So first thing first, let's check compression...
Johndeere yanmar engine 2T80 leak testing JD650 compression part 2
มุมมอง 383 ปีที่แล้ว
In this video I got a johndeere 650 that crank but does not start. it has overheated the previous year and water pump was replace. the block is crack, caused by rear implement that did not had proper support to front end. so oil level was not high enough. when engin was working there was a bottom end knock. So first thing first, let's check compression... part 2
Johndeere yanmar engine 2T80 leak testing JD650 compression part 3
มุมมอง 2223 ปีที่แล้ว
In this video I got a johndeere 650 that crank but does not start. it has overheated the previous year and water pump was replace. the block is crack, caused by rear implement that did not had proper support to front end. so oil level was not high enough. when engin was working there was a bottom end knock. So first thing first, let's check compression... part 3
Johndeere Yanmar engine 2T80, JD650 split in half
มุมมอง 983 ปีที่แล้ว
In this video I got a johndeere JD650 that crank but does not start. What it look like with JD650 engine on the floor... Let's remove it!
Johndeere with Yanmar engine 2T80, JD650 engin off!
มุมมอง 1023 ปีที่แล้ว
In this video I got a johndeere 650 that crank but does not start. There it is, engine on the floor...
What is good compression for those engines ?
ALGUEM TEM O SOFTWARE DO PROGRAMA
Good morning. I’m in Phoneix Az. Do you have the software Omron Programmer 9.6 available?
Hello, I have a 1985 John Deere 650 with the yanmar 2t80 and I cant get it to start. I’m getting fuel through the lines with no air, it’s turning over, but we are still blowing white smoke out of the exhaust. Any ideas on why it may not be starting? Have not pulled injectors or done a compression test. Just replaced all fuel lines, new fuel filter, and new starter. Any help is greatly appreciated.
Sir i have 6 faulty omron plc . They all have power supply issue . They didn't give 24volt and 5 volt dc. Could i use a seperate SMPS for 24volt dc and use an IC 7805 to convert 24 volt dc to 5 volt dc which are coming from SMPS. Did it work??
Hi sir good day my board connection is only 5 wire your is 6 wire which model you use my is ( CPM1A-40CDR-A-V1) can guide me how to connect it Thank you
Hi SIR Sorry my late reply i was away my since cannot work i have try alot of way i may find 2 2nd hand type to replace it keep in touch to lean from you , Thanks you .
Very little useful information For a 12 Minute Video...
Provide me your email plz
What is the cable you use to communicate with the PC?
USB-C1F02 usb to RS232 adapter
It is call a serial to peripheral cable, you can find a USB to peripheral cable but mine is a old one. so I use a USB to serial converter. My cable does not have the number on it, I would guess USB-CIF02 here is a link :www.indiamart.com/proddetail/omron-plc-programming-cable-cqm1-cif02-cqm1-cif01-usb-cif02-usb-cn226-keiko-international-3641646688.html
@@LinseyProgress Hi sir my cable too very old ready i did not know how long still able to use it thanks you
I would like to know where you got your parts? And i have a few questions if you don't mind
Where are you located? Sounds like you have a french accent. In quebec perhaps?
How much do you charge to fix smarts i am in Montreal