วีดีโอ

Great video! I am just running into similar issues, I hope your advice will solve it. Did you mention you replaced your extruder? Can you share what extruder do you use, and why?

Hi, great videos! I am considering purchasing a PrinterBox for my MK4. How long would you say it took to assemble the box from start to finish (not including the Pi - I won't be using a Pi in this box). Thanks!

Thank you very much for the explanation, I learned a lot from you. 👍

Isn't capricorn tubing tighter? As the PTFE tubes are only there to guide the filament and not feed like in a normal bowden setup, wouldn't you want the tubes less tight? (like the 4od 3id mm ones)?

Thank you! This helped really much 😊

Thanks for sharing, as I have Metod and wondered if the Sindvik would need additional holes to mount

thanks for that, given me a great idea for enclosing my Prusa Mk3s and recent Bambulab A1

Great job I have been unable to locate the back adapter plates for the conversion for pmw I checked on Prusabox and Printables the plates I'm referencing are in this video at 1:59. would greatly appreciate some guidance to find them. Thank you in advance sir

i'd been trying to adjust the spinda forever to get the self-test to pass on Z axis, and replaced the trapezoid not all to no avail! Adjusting to 191 (I also have the bondtech) and now everything's green! thanks!

perfect sound. no need for expensive exhaust systems

hi colin i dont understand why you need the buck converter when all components are 12v

4:30 for set up

Hi Colin, thanks for the in depth video! Cause of you I just collected all the mentioned stuff from the PO Box. I will use your design on my TLX for the MK4 and I was just asking myself if you have a new design of the PSU shroud which fits the noctua 40mm you have in this video. Also since the TLX just hs 2 screwholes for the PSU shroud I would be happy to get the step or fusion file for your shrould to change it to the "new" tlx layout.

Hi Collin, I cant fin a cable that goes out from the pcb to a fan splitter, can you help me out^ Thanks for the vid!

Minute 1:54, you use an extension cable, but have you changed the connector? That white female connector is different, it is wider. What is that connector called? The connector on the Zhiyu board is wider than any 4-pin connector and I don't know which one I should put. Thank you!

Followed your instructions by watching the wiring 10 times lol. Not a big hero with electroncis but got it working. Thank you so much!

i am reviewing all your video's but where the heck did you order that buckconverter? My prusa box is assambled now so it's time to do some upgrades :)

what is the temperature during several hours of printing? Will the power supply and electronics withstand such temperatures?

Thank you so much for this video, I have the exact same relay board and no instruction so of course I wired it with the wrong vcc pin and it drove me nut with the relays working randomly when they felt like it. With your wirering instruction it works like a charm now. Thanks again!

Very helpful. Well done video. Thank you!

Manual?

Hello Collin, respect. The circuit is really great explained by you. However, I still have one question for you: Does the circuit also work with a simple 2 cable control of the fan? Greetings Frank

Very neat solution Colin! At the end of your video you talk about making a fire extinguisher system video. I have not managed to come up with a practical solution using CO2 so as not to ruin everything with powder or foam. I would be very interested to see what you plan to do

Thanks for this tutorial. Can I ask you how did you power the screen?

Bonjour, ou peut-on trouver les fichiers des entretoise arrière svp ?

I am currently following your idea, I have purchased the materials and built the Metod. Did you brace the back of the unit with a plank of wood by any chance? Thank you in advance.

Great, thanks for sharing 👍

Thanks for the video. Does it keep all the settings after power off? Or must I reprogram my temperature settings at each power on?

Is the knob controller a true PWM controller or just a variable voltage controller? I think the Noctua PWM controller gives you more control over the fan speed.

I just want a pwm controller without temp probe to control a fan? Is there a driver for that? I found a noctua pwm controller for $25 but its too expensive.

where did you get your material enclosure ?.

Good video. What 12V to 5V power converter are you using?

I just wanted to say thanks for the great how to! I was using this on my octoprint, and recently switched to Prusa Link/Connect. The switch and script still work great!!!! Thank you Colin!

I've been looking to get these on my S5 for a little while, other videos didn't really show what I W as after as I was worried about the cabin drone, did something similar on a mk5 gti and i ended up taking them off again as was too loud for me and I got a resonated system instead. Thanks for the upload - this has given me my answer, this will be too loud for me.

Can I set the close temperature above the start temperature? That way I never go too slow. I was thinking running 12v dc compressor ,and I think if it runs too slow it might damage the compressor...

thanks you solved my error 🤠

I am using the version of this controller that allows for 2 fans, 2 temp sensors, and a buzzer. I am currently designing, testing, and creating a 3d printed cooling system for a Kicker CXA car amplifier. It's turning out great so far.. still need to do some final touches to it. The board works as advertised. Great electronic board to help with the project.

Hello, thanks for taking your time to make these videos in such a detailed way, is it necessary to use the buck converter if I use a 12v fan with a 12v thermostat?

Hi Colin, Thank you for taking the time to produce your informative and pedagogical video. Much appreciated. I have been contemplating doing basically exacly what you did in this video, but with a digital controler solution. I.e. rather than setting things up manually, I would like to set the parameters and access temperature controlers using a zigbee hub (I use Hubitat Elevation). Any thoughts on if and how that could be done?

Great video. Seems like an easy way to run logic for relays in PrusaBox

This was a very helpful video thank you so much

thank you

thank you

If the Buck Converter Converts 12V to 5V, then how is the Fan getting the 12V it needs?

would an anycubic vyper fit inside this?

Hey Colin. Great video and I am going to try something similar for a lack enclosure I have. One question, do you think it is worth having an incoming fan as well as an exhaust one? That might keep it from getting too hot and therefore too loud. I mainly print PLA and have started PETG, but I am using the enclosure for noise cancelling predominantly. Thanks again.

You put links for the enclosure, which the video isn't about, but no links for the extruder, which the video is about. I seriously question your reasoning.

Thanks so much, I struggled with the official instructions due to things missing - this helped a lot

Thanks for all the videos, mate. Can you tell me how long it took you to build the tank? I’m asking because my arthritic hands took almost 8 hours to build my PrusaBox

😭 *promosm*