วีดีโอ

Too much farting around. Just restore the damn thing.

Despite the seemingly poor job of electrolysis, the restoration job was beautiful, and the hand operated grinder looks much better than before. Great work.

Suggestions: The sound of scratching and pounding on the table is annoying. Minimize it. Don’t wiggle the parts when you hold them up for us to see. It is hard to see them while they are moving. Still is fine. I do like that you don’t have music, this isn’t a broadway play. ;-)

Ce travail des fainéant 😮j'espère que vous allez finir à vec

You really need to take some time and research what those processes you are using actually do and how they do them. I bet you were not happy with the results from your electrolysis. It was done wrong. - Heavier gauge wire would be helpful. EACH PIECE needs to have a wire so the current can run through it. The sacrificial iron piece needs much more surface area. It needs to just about match the surface area of your piece to be cleaned. Do some research on the best chemical(s) to add to the water for the electrolyte. - Penetrating oil is just that, for penetrating into joined but rusted surfaces so they can be separated. It IS NOT a full rust removing chemical for all those flat surfaces. I am assuming you were using "WD-40". The name means "Water Displacement formula number 40". It does just that, gets a very light lubricant into tight areas by displacing any water. It may also be used to help remove water from rough surfaces like after you do the electrolysis process and it leaves an oily surface behind to prevent flash rusting. - The sand papers you were using were not aggressive enough at the point you were using them. As you saw they did not do much. That grit level was for later in the process when you are trying to remove the scratches from a coarser grit that should be used first. Match the grit size more closely with the pits on the piece you are trying to smooth. This heavier grit will leave scratches that you then remove later with progressively finer grits of paper. -I'm not sure what the chemicals were that were blue you used later but it looked like you wanted to clean the brass bushings. Again, research and understand your chemical processes. What works for brass will be ineffective on other metals. -You can use small end brushes in your rotary tool to help get into tight places like the ends of the slots and gear teeth. Pro tip: put a piece of heat shrink around the bristles of that small end wire brush to keep them compact for those tight areas. - Use a wire brush ALONG the knurling pattern in the knobs not across the pattern for more efficiency. - There was a wooden handle required at the end of this tool's crank lever. (The small screw in there was not the correct piece.) And lastly, -The interior of the tool needs a heavy grease on all gear teeth and bushing surfaces. Your video work is fantastic! You have that figured out! Excellent! Keep trying! You'll be great!

Worst rust electrolysis removal ever 👎🏼

Super jesteś Zrobione odrestaurowany tylko takie elementy to się piaskuje i trzeba drewnianą rączkę założyć do tego młynkę Pozdrawiam serdecznie. 👍👍👍👍

Another great restoration 👏👏

sorry, but this is one of the sloppiest work I have seen, 👎

Wonderful restoration job you did on the strap tensioning device. It looks much better than before and it works like a charm too. Excellent work as usual.

Nice 💯🎉😂❤❤

Don’t quit your day job.

Ripoff

😂

great

great

Guy being sexy with a tool ......ahhhhhhh

Fake ~ fraudulent 😡

Beautiful restoration job. That juicer looks much better than before and it works like a charm too. Excellent work.

great

🥃👍🥃👍👏🥃👍👏🥃👍👏🥃👍👏

❤

Belle outil

Esta guapo pero no practico para el uso se puede mejorar muchisimo

For gods sake try a pressure washer , or even a warm soapy bath , its not made of glass !!!

Why do you waste time taking the loose rust off and going through the grades of coarse paper when you know that you'll be using an angle grinder with a flap wheel??

great

💯👌👍

Công việc của tôi thường leo cao. Ước gì tôi có được cái búa giống như của bạn. Rất đẹp

Super jestem pod kuferka wyremontowane Pozdrawiam serdecznie. 👍👍👍👍

@refri you're the one who has no idea about reatoration.

not really sure why this guy just didnt leave the grinder in the electrolysis bath it would removed all the rust and he wouldnt have had to do much work at all also not sure why he painted the grinder he made it unsafe to ever use for food again where a simple seasoning job would have made it usable 👎 bad restoration item cant be used safely for its intended purpose

Would have been a good idea to straighten the moving part as it is bent like a banana ! Thats why the laws are so far apart when closed .

Nyc

Using a pliers to unscrew the hexagonal bolts is far from my idea of restoration. You just cleaned the tool up. No restoration here.

Restoration ???!!!!! Are you kidding me???!!! At most a repair. I think you have no idea what a restoration means.

great

почему у тебя всё обмотано проволокой???

херня...

Глиною обмазав, а тоді дав просохнуть, і дуре людей який він майстер реставратор, баклан ти, навіть обдурити якісно не можеш.😂😂.

Very nice job 👍👍👍

Just scraping all that crud of must have been very satisfying.

Too much advertising...4 advertising shorts during the video

Wow, is this an archeological find? How did it end up looking like that?

Нож при сборке правильно поставь пожалуйста😊

😅

LEVELS ...

You're not reuploading content very well

Another great restoration 👍👍

Fuckkkkk outa here, Most unsatisfactory video I've seen in this genre