วีดีโอ

Is it just me or does this guy look like he's really gotta pee?

Your tip saved my sanity! It works So effectively. THANK YOU!

I've gone through the troubleshooting, and ended up replacing the vacuum switch. Now, it feeds pellets when I turn it on, but doesn't continue to feed them for very long after that. The amount of time it feeds them seems to vary. Suggestions?

Works like a dream! Thank you thank you thank you!

Thank you so much! My issue was the hopper lid switch. I made a jumper with a piece of insulated wire, removed the switch and jumped the leads, turned the stove one, and it started feeding pellets again. I ordered a new switch and am hopeful I will be fully operational again.

I learned so much from this video, thank you so much! If you have an Englander stove you should watch the whole thing, even if you aren't having problems. I found new places to clean I didn't know about!

Thank you for this. Please support this site by purchasing from them.

Thank you so much! Save me and my grandpa from the cold!!

I am looking for next video after cleaning all front of stove, you say now turn around to back - to be continued. How do I get that video that you did?

Went to auto store and replaced plastic hose with automobile vacuum hose

My top auger don,t turn it seem like no power there new auger motor now what should i check

I might be wrong but I thought the exhaust fan pulled the air through the burn pot

Excellent video. You helped me find my blockage of air flow.. I did replace the ignitor. Thanks again!

You saved me on a cold Winter day! It was the switch. I ohm checked it and it was open. Worked the switch a few times and blew it out with shop air and that did the trick. I will order 2 and have them on hand. Thanks again!

Thanks for such an informative video! I have an issue where my stove stops feeding pellets so eventually the fire dies out and the stove turns off. Does anybody know if there's a sensor or something that's not signaling the stove to dump more pellets into the fire? For the record, the stove initially feeds enough pellets to get the fire started but then doesnt dump anymore so the fire dies off. Please help!

I moved an have a Harman already here but i can't get the hopper open?

Thanks man You saved me.

Excellent post

Very well done and informative video! Do you sell the cold air return kits for the Harman P43 stoves? If not do you have the info for what I need to install one?

2022 P130B model, the lid switch box has been redesigned. The switch will only work installed with the lever pointing to the rear.

Any help with why my auger won't stop feeding? I have 2 of these. Swapped the lid switch and diaphragm from the properly working stove. Hasn't made a difference. Not sure if the auger motor is bad or the control board. Stove runs if I trigger the switch manually. But won't stop feeding otherwise.

What if the the motor it’s self isn’t spinning what then?

Good site, this will definitely help a lot of people. Let me run a story past some of you , it may save you or someone some hair pulling out. I have been working on the same pellet stove, the stove will start, it will dump pellets for about 10 minutes, it will ignite but then it will shut down. I put direct power to the auger motor so I didn't think it would be the auger motor that was bad. So i bypassed the vac switches still no auger , I figured it had to be the heat sensor, not sensing the fire in the burn pot, some stoves have a snap disk that performs a similar function but on this stove it appears it is like a thermocouple screwed in directly under the ignitor. So I replaced that, the unit ran for 10 mins again then stopped feeding, I quickly pulled the wires from the auger motor again and ran line voltage to the ager motor . . . .would ya believe the auger motor would not turn now ? seems the auger motor was getting incredibly hot and when it reached a certain temp, it just stopped , until it cooled down enough , then would spin. Bad windings in the auger motor! if anyone has a similar issue just rule out bad windings too just let it run, run run and see if the auger stops on it's own. when I found it was not the pressure switches and not the circuit board and not any kind of hopper safety switch , I just assumed it had to be the heat sensor switch and I was wrong. It was a good thing I was still there when it failed though to retest the auger motor when it was hot

I have a 25-CBPAH that I bough 10/2021. I having issues with this model and I don't see much videos on it. I've replaced the augar motor, vaccuum switch and hose, combustion motor. Cleaned out the little hold from hose to front where ash bin is. It will light and run at startup. Room blower doesn't come on at this time until I manually have to push feed up for it to start working normally but after a certain level like 6 it will sort of choke up and automatically shuts down. Fellets are feeding little. i ordered the augar motor accordingly to manual specs but still feeds little. i had question on CCW is what I need. I don't know if its the fellets itself but its driving me crazy.

Followed the recommended steps and....................jumped the door switch. Ordered new door switch. Stove is back working like a champ. Thanks for posting this.

They made it as hard as humanly possible to get to the fuse. Ridiculous. We've watched your other videos and have isolated the problem (pressure switch) but in the course of doing it..... a small short happened and the fuse popped. Now we're spending forever and having to remove the entire control board just to get to the fuse. Jesus. (But thanks for these super helpful videos!!!)

Thank u so much man u helped me solve my problem and get my stove running again, helped me with so much frustration

Thank You!!!! This worked for me last night! You are a savior!

great vid...about to do mine vavavavavavavavavavava

can't find this info anywhere-have a p61a-2 -the stove burns too hot--replaced the board and it burns hotter--the feed is 7+ seconds/min on lowest setting in room or stove temp setting--what shud the low burn feed time be--also any idea if something other than air leaks can cause this

I can unplug the bottom auger motor and plug into the top motor, and it turns, but it will not turn without being plugged in to its own power source

I just bought a blower and some other parts....but i did NOT order it from this annoying jerk!!! Dont need moronic sound effects!

ALSO If you don't cut all the way across your pellet bag. Leave 3 or 4" of the bag corner intact. This pocket easily catches ½ of the sawdust in the bag. The bucket/strainer catches the other ½. Dump these spoils into another bucket every day. Bout once a month i'll blow my shop vac exaust through this. Dust blows away, pellets stay

I cut most of the bottom out of a 5 gal bucket, leaving about a ¾" lip remaining. Next i cut the bucket in ½ verticaly (keeping the handle side) forming a basic trough. Then i formed a piece of ¼" mesh hardware cloth loosely to the inside of the trough bending it over the ¾ lip i left on the bottom perimeter, stapling it to the inside ½ of the almost bottomless bucket. Now Lay this screen contraption right in your hopper and dump your pellets on top of it. Simply lift up on the screen, tilting forward and LIGHTLY shake it as you pull it up and out of the pellet pile. The pellets are too big to fall through screen so they spill forth into the hopper. The dust on the other hand falls through the screen and piles up above the ¾ " lip. Now you've got a bucket/screen with a strong handfull of sawdust out of every bag. No Brainer

Did you ever make a video showing how to attach a thermostat?

Another thing that could help till you figure out what’s wrong is to wait till a small amount of pellets are in the burn pot, grab a single pellet (long to medium sized) and stick it in the igniter hole touching the igniter and hanging out. In the 10 years I’ve own this model of stove I’ve never had a problem with the igniter lighting my pellets except every once in a while but this is most likely to be a case where the pellets fall in a weird way into the burn pot. Probably the case of being too far away. Anyways if this happens I always stick a pellet into the igniter hole and it always lights after this. Hope this helps some people.

Thanks for the informative video demo. Now im headed out to my garage thats 3 degrees inside currently and try the things you have shown. My pellet pro stove has been used 3 times in the 1.5 months ive owned it. Around 12 hours of total use and already doesnt work. Fuckn junk. On a side note... your voice sounds very similar to David Schwimmer

Not true about the USB port, mine is on the side facing towards you.

Mine was just a bad hopper switch! Thanks for this video! Saved me from buying a new motor 🎉

Outstanding Video!! The best explanation of the parts and functions of the stove.

Thease control boards are the heart of the stove,they need to be adjustable and resetable

You talk too much

How do I stop a pelpro pp60 auger motor from turning and wrapping its wires around itself and unplugging? It will randomly do it and I don’t know why or how to stop it it’s set how it’s supposed to be

You, sir, are a genius. Cant thank you enough!

Awesome video! My problem was the lid switch. Followed your instructions to diagnose. Stove is up and running. New switch will be here tomorrow. Thanks man!!!!

Great video and thank you for putting it together, but "it's simple" then proceeds to show all the parts required in the feed system (overly complicated for pushing pellets). -lol-... Honestly though, I would start with the most basic first. I was hoping to find how to "prime it again"(when you run the stove empty, empty) because if the pellets don't reach the burn pot it may seem like its not feeding. We just got our pellet pro last year and it heated our house on the lower settings(huge improvement from the napoleon we had for 8+ years), when are you finding that these additional steps are needed? 2 years in?? 3?

Also the Auger turns in opposite direction and switches disconnect.

Where can you get a new pin? Mine broke and the motor fell off. Also when I replaced the motor there was black grease on the old one. Should I be concerned about the grease?

We have an older Englander and the room blower won’t start up. The blower works when plugged in directly. What should I be checking or replacing.

I replaced the igniter today, and in the process, I must have have knocked the vacuum tube off the auger pipe -- watched video and had it running in about 5 minutes. Thank You !