วีดีโอ

Did yall replace the drive belt with a chain?

I would think keeping it light and you get more speed out of it just my opinion thank you for the video

Never understood why they rate them by horsepower; I'd think torque would be a more important number. I'd not expect a 30 series to hold up on a 420cc, even if you kept the rpm down to 2500 so that you didn't exceed 10hp. Nor would I expect a 200cc running at 6000rpm to bother a 30 series, just because it's now putting out 15hp...unless the pulleys grenade at higher rpm. Do they slip on "small blocks" with higher HP? Perhaps the belts just aren't up to the task? You got me all interested...right until you weighed it. Not worth it, knowing that.

Thanks this will help me

by chance are the driven/jackshaft diameters the same on both? is the pulley spacing the same? if the spacing is the same that could use the 30 backplate, at worst swap the bearings to one with the correct id. just a thought as i don't have them here to look myself lol.

I have no doubt you can make it work.With the case plate on,and turning the set-up towards the head,as it will be mounted that direction, you'll be able to make a shim plate that works. The main thing is to Not have a hollow sleeve inside the clutch for the key.Cutting off a crank from a broken engine and drilling it out so a long bolt will join it to the crank should fix that.?.

I am removing the governor on a duromax 440 electric start and putting it into a ct200uex minibike. I am posting all the videos of me working on it when it’s done on my youtube. Thanks for this helpful video have a good day!

i put a 440 in a g1 golf cart with a 42 horsepower clutch and stock rear end haven't had a prob with it i love it great power pull anything you want great fuel mileage

How long did that stick flywheel last?

That looked like a fun workout. I look forward to the vids and what you do to upgrade each.

Y weight of average

What camera do you have on the mount?

Hmm I wonder how this clutch would work on a mud mower rather than a drag mower. I have a craftsman on 26” mud tires 5” pulley in the rear 5” up front

125cc Chinese four wheeler

@RCG Racing... go check out "Diesel Fuel Network" and his "hot rod tractor". If sure you've seen it already but IF NOT its frickin cool

It looks like you had 5 G without the air filter on it stayed for a little bit thank you for the video

Enjoyed it very much and made an awesome video thank you

Thank you for the video

Awesome video and it look like a lot of fun thank you again for the video

Good job to you and John on the more technical trails you guys did good considering you all usually are the mud slingers lol.

I'd try and figure out a one link for the front, much like the snapper comet has with the tubular frame to the front end. Mine would flex well over 90 degrees as a kid

Great video dude! You got some great shots over the day! It was a great ride im really glad you guys made it it was great seeing and riding with you again!

I’m actually pretty impressed with how you made the open diff go, got a little sketchy couple times but you made it work, I’m hoping to make it to the Mowventure up there this year

Looks like alot of fun😊

Nice rigs

I have one with a 10 to a 50 on the rear wheel I get bout 55 I want higher top speed what gear should I run cuz I tested a 13 today and it gave crazy torque but no top speed well I got 47 but the motor didn’t like the gear

What would be a good mower for my friend he wants to start

Make a new motor mount and lean the motor either forward or back to fit under the hood, this fuel injected diesel should run fine as long as the sump can splash oil around

Just got my parts from NR the flat top they sent me has the weird oil cut outs instead of the holes just something I noticed I think I'm gonna end up getting the first combo u said with the ducar rod even tho I'm gonna have to buy the same one again for my actual ducar 212 😅 at least I'll have extra parts for another build hey man thanks again for all your help and awesome video

👏👏👏

That motor sound real fast I like how you hit the gas and you did a pop a wheelie thank you for the video

Do you think there is room for an ammo can toolbox between the engine and the dash, above the battery?

What's interesting is about that carburetor set the carburetor has problems you can't get it up to top speed thank you for the video

I was hoping you were going to do more mud mowers of your creation now I know where John gets his creation on from and he's really good at it thank you for the video

For that filter under the mower I would add more to protect it if you hit something from the side or you run over something that sticks into the filter your going to be sitting there and can't move i know you have lot of pieces of steel or pipe laying around

Can you do a video about putting a cvt torque converter on a lawnmower

AKA, "Mud Mower" for your property.

With the winch mate I run a momentary weatherproof rocker switch wired up on my dash wired into the winch solenoid and it works great it's always setup ready to go no having to carry around a remote or anything. The winch I got has also got a wireless controller but never use that but handy to have if working on it whilst it's hanging from the roof with the winch can lower it while underneath it if lining up something

Very interesting thank you for the video

Thank you for the video tore that belt right up on

That was cool that John was inside that dragster car thank you for the video

I don't know much about the whole thing I enjoy watching you erasing them I would think if you change the Jets to bigger you would get more gas and you'd be able to go faster that's just my idea my opinion I don't know thank you for the video

Awesome video of the car show and walking down the strip to see all those cars that was pretty cool and that little will cart that John was showing that pickup I've never seen nothing like that thank you for the video

Thank you for taking us to the races with us and that's awesome you guys I went together as different characters for Halloween thank you for the video

Good run race member 💪🏼💯💨💨💨 u were definitely out there

Cool❤

Hey @RCGracing omB just told me I need the 3.303 for my 208 should I just get the one u did and change the piston kinda stuck on which to go with i just want a back up so I can build my ducar ?

what puzzles me on this 3 circuit carburetor is that I don't see where the air comes from to the 3rd circuit emulsion tube. It seems it uses the same circuit as the main jet, trough a small hole, but the hole is covered with fuel, so the 3rd circuit squirts only fuel. Any thoughts ?

If I have a 0.042 main jet, which size do you think I should try on the intermediate jet ? If I add the intermediate, do you think I should reduce the main jet ?

And look like a lot of fun thank you for sharing and thank you for the video