วีดีโอ

Hi @steffie.morris, this is common problem with the side plug inside the roomba. For protection of the roomba, when you charge from the side port it disables charging from the dock. This is a great when it works, but sometimes the side port plug is damaged and it fails so that the roomba always thinks its powered from the side port (even when its not). Some people have fixed it using a small screw driver or just inserting the side plug and giving it a wiggle. I haven't had that much success. Best to buy a replacement plug on ebay or you can remove the side plug and solder a bridge (in this case you wont ever be able to charge from side plug). Check out this forum for more info on the problem. www.robotreviews.com/chat/viewtopic.php?t=17389

Clean floors 1; landfill 0

@@drroomba5045 thanks!

clunking will be the brushes reversing direction because the roomba has seen a high motor current and thinks something is jammed. Question: did problem happen with old brushes? did problem just start happening or after thew new brushes? if you are tech savy, you can make up a cable and connect to the roomba and run built in tests to see what the motor current is doing.... could be motor issue or issue on motherboard. Where are you located? other idea is to look on marketplace and pick up cheap 2nd hand one and swap out the bush module. If you were in Melbourne, Australia, I could help you out. See this video th-cam.com/video/m7OG5IMrgiQ/w-d-xo.htmlsi=ZRidvpa5VI3RW44z

Pas de problème!

Not in this case. See my description which explain the fix

@@drroomba5045what the nok?

@@vacmaster2332 the LHS main drive wheel encoder was NOK. Replacing wheel motor fixes issue.

Thats why they called me Dr. Roomba 🙂

Thanks Dave. Yeah, I follow both those guys. It’s a bit of a drive but I love it there. However my car always ends up worse than Vas’s. Can’t figure out why 😂 Hope u are on the mend. Sounds like u got a bit going on

best thing is to look on places like facebook marketplace for a cheap second hand roomba. In Australia, you can sometime get them for $50 or free if broken. You can then take the parts from that one. If you were near me, i would send them to you !

@@drroomba5045 Hi, I´m from Czech Republic, so on exactly oposite side of Earth :D

Please, how to activate on series 600 service mode to test brushes motor and gearbox when robot is on bottom side?

@@Dzordzikk see th-cam.com/video/m7OG5IMrgiQ/w-d-xo.htmlsi=0qfsTcshiVfOH9Vz&t=92 please like and subscribe

Hi Can u remove both brushes and run. Then run 1 brush at a time. Report back. Ta

Yes, I tried that and it ran fine with one brush at a time. Either one ran it for 10 minutes.

And then I stopped it!

I’m curious, Can u put back old battery and see ?

@@drroomba5045 Unfortunately I got rid of it.

whats the problem? Dr Roomba is here to help always

@@drroomba5045 thanks it’s showing error 8 I opened it and cleaned it the red dot fell off when I opened the robot so I taped I think I didn’t tape properly but I think that’s the problem

@@nehaanshaikh7223 what Roomba model ? Also please explain what Roomba is doing when fault comes. Only then can the dr help

@@drroomba5045 okay doc it’s showing error 8 when it’s charging and it’s model 695

@@nehaanshaikh7223 apologies for the delay. I just saw your response. Difficult to troubleshoot without putting the robot on my operating table. If I had it I would connect my laptop to it and run the diagnostic tests. I did a video on this here th-cam.com/video/m7OG5IMrgiQ/w-d-xo.htmlsi=NLfdw40YQttnmuhA

re: the red dot - see 7 min mark on this video th-cam.com/video/kkYGPOfOvf4/w-d-xo.htmlsi=MmMn-RveV7N1moaz

shes a talion !

Nah, its the Talion. Its soooo good. My favourite

did not notice I was first lol

Yes indeed, Well done (first)