- 10
- 26 686
CT Outdoors 203
เข้าร่วมเมื่อ 27 ก.ค. 2022
Everything outdoors- fishing, hunting , trapping, ATVs, guns and more
วีดีโอ
Honda 250ex grab bar touch up
มุมมอง 27ปีที่แล้ว
The rear grab bar on my sons Honda 250ex was looking rusting and chipped paint so I decided to freshen it up.
Pond Prowler mods light and switch panel install Part 2
มุมมอง 6K2 ปีที่แล้ว
Part 2 of my lights install. This video I install the deck lights and switch panel. 3 Gang Waterproof Marine Boat... www.amazon.com/dp/B08THFDW5C?ref=ppx_pop_mob_ap_share 10 Pack Marine Boat LED... www.amazon.com/dp/B08L67HDB4?ref=ppx_pop_mob_ap_share Shangyuan Boat Light Extension... www.amazon.com/dp/B07HB7MC9Y?ref=ppx_pop_mob_ap_share
Pond Prowler 10 lights install Part 1
มุมมอง 6K2 ปีที่แล้ว
I installed navigation and anchor lights on my pond prowler. Links in the description of the parts I used. Shangyuan Boat Light Extension... www.amazon.com/dp/B07HB7MC9Y?ref=ppx_pop_mob_ap_share White LED Marine Navigation... www.amazon.com/dp/B07Z1G1V9G?ref=ppx_pop_mob_ap_share Marine Boat led Navigation Stern... www.amazon.com/dp/B081NX678C?ref=ppx_pop_mob_ap_share
Pond Prowler drain plugs
มุมมอง 3.9K2 ปีที่แล้ว
I bought this used and it had water in it so I installed drain plugs in each pontoon.
Pond Prowler cart
มุมมอง 7K2 ปีที่แล้ว
I built a cart for my pond prowler so I could easily pull it around at the launch or in my yard to avoid scraping the bottom. #outdoors #fishing #pondfishing #pondprowler #bass #pelican #sundolphin
Pond Prowler paddle holders
มุมมอง 1.3K2 ปีที่แล้ว
This video shows how to for installing paddle holders on your pond prowler, pelican bass raider or kayak
Nice vid. I thought that little bug was on my phone....8.56....I went to brush it off. Haha😂
@@jnancy-pants3957 hahaha I just noticed it.
Brilliant idea using the magnet to pull the wires. Where did you get that magnet?
A friend had it laying around. I’m sure you can find one on Amazon
OK. Thanks. Another question. Have you put boat registration numbers on your Pond Prowler? If so, how did you get them to stick?
🙆🏼♂️🙅🏼♂️🤦🏼♂️
That actually came out very nice. Only thing I would do differently is use all red lights inside. When out on the water fish don't see red light. Insects do like nats or mosquitos. And you have extra switch? You could put flood spot light on front when traveling from on area to another
Good idea with the magnet and nut, but I have a suggestion that make make it even easier. I would say a light string would probably work better. My reasoning for saying that is it is lighter, more flexible, and would have less chance of causing the nut to drop. Just a thought. Cheers.
How have these drain plugs been working out for you?
No issues so far.
I've got a couple I'm about to install and the nerves of cutting holes in my boat are getting to me a bit. 😅 Fingers crossed.
These come with 2 drain holes on the front of the hull. One on each pontoon.
Must be a newer model. Mine definitely didn’t have plugs.
mines 7 years old and has the drain plugs up in front pontoons
For the 2 x 4’s. Did you cut 4 - 4ft and 2 6ft. Thanks for the video.
I had scrap 2x4’s I believe
New Sub, I'm doing this to my Quest Angler 10 soon.
Great video bro!!! Keep up the good innovative work!!! Inspired my friend
Thanks man!
I like the magnet and nut trick. I'm about to do the same installation on my pond prowler so this trick will help me alot.
Awesome! Let me know how it turns out!
It turned out great got the lights and switch panel installed.
I bought a new pond prowler and it has drain plugs in the front now but after leaving it at the dock for a week it was full of water. Bass pro said the seam gasket takes on water in the rain . Unfortunately I'm taking it back and just getting a regular aluminum jon boat
just go around the seam gasket top and bottom with silicone and no more water issues, i also removed every screw and added a rubber washer then siliconed around everything the screws went into, aint had a single drop of water inside the boat again.
I would recommend marine grade epoxy for your screws, marine grade silicone is technically a lubricant and can cause screws to loosen over time, especially if you’re running a gas motor that vibrates a lot. I’m sure the silicone would be fine but epoxy would be extra security
Thanks for the input, but I’m just running and electric motor. So far so good .
I also went to harbor freight and got some of the floor mats the rubberized ones and cut them to fit the floor which made the boat quiet when moving around
I used this video to help me decide how i wanted to mod my boat, i pretty much done it the way you did except for using solder on all my wires and shrink tube, then i used marine sealant around every screw hole and every place any type of moisture could get in, this is the only video for thie pond prowler 10 i could find so if you do any other mods it would be nice to what they are, i also ran wires for 2 lowrance hook 4x the switches i use 1 for running lights 1 for interior lights and 1 for fish finders works great thanks the info on showing it can be done
I don’t see the link to the plugs in the description. Do you still happen to have it? Much appreciated! Nice vid btw 👍
Sorry about that. Hope I’m not too late Kayak Drain Plug Kit Boat Scupper... www.amazon.com/dp/B08HS63NJ4?ref=ppx_pop_mob_ap_share
very. Nice and helpful. thanks
Thanks for watching!