วีดีโอ

I guess you should have ask the internet on how to not installed your hooks. These experts really beating you down. Welds look good those hooks are not coming off i think i would invite these experts over to see if they pull them off.

is it mandatory to have the bucket OFF the tractor to weld this on? ie: electrical current going thru the tractor to short circuit electronics perhaps?

Where did you buy these

Got the same tractor. I can the same, maybe even a better job it’s my brush hog and my grapple bucket. I just rip all the crap do not and run over it. I am personally not that impressed with the lane shark. To small and underpowered . It is a what it is. Not loving it

Awesome setup, like the extra protection on the hoses. All ran nice and clean.

I know it has been a while since you did this. Would it work to just weld the blocks together? The bottom box just seems like extra work for little gain.

You haul away or burn the piles?

Love your videos bud because of this video I just got the laneshark

You never showed the wire hook up system. I wanted to see if colors of wiring match up or not.

It's best to weld the hooks to a buffer plate first. Round would be first choice, but a square or a rectangle will work too. Just be sure and wrap the corners of the buffer plates when you weld them. Unless you're using gas shielded fluxcore, that is a welding job for 7018.

Does the cab AC have an air recycle option like a truck/car does? JD 4 series doesn’t and the AC doesn’t want to keep up on hot Texas summer days

Hello, I like your videos, I like the way you use the lane shark, I like to get one for my farm, I see you had another equipment at the back of your tractor, can you give me the name of that equipment please and where to get it? Thanks for your time

Thank you for the video. I just ordered my weld on hooks from Amazon four for $20. Hope my welds turn out that nice.

Did you burn the shit out of your jacket?

For black berries do you think a clamshell grapple like yours is better than a root grapple ? thanks

The Jensen wiring harness that came with my radio includes a noise suppressor. Perhaps this is something they've recently added??

Its so nice to see someone actually using this attachment on REAL limbs and brush. I hate when people only cut small bushes and grass...SHOW ME WHAT IT CAN DO! BTW, do you know what the cutting capacity is for the Laneshark?

Great job

How does this compare to using a Box Blade for gravel work?

Get a pole saw , bobcat following push everything to side , simples

Cooking some nice bacon 👍

Nice weld. I found that flap disc works well for removing powder coat.

You should keep you bucket low to the ground when travelling with a full load, keep the center of gravity low or you are gonna put that Grand L on her side one day. Raise the bucket to dump when close to destination, in this case the dump truck. Good luck.

How about a 2 year review, pros /cons , looking to trade up from a Bobcat. What differences are there with the Grand model and basic 4760. Thanks for sharing.

We’ve got a 444 international, good tough tractor, we’ve had it since 1974, thanks for the video

Why does it sound like mower keeps turning off and coming back on ?

I love how your bushhogging with both the front and back of tractor at the same exact time hahah

Nice place. Just lower that loader a little lower to ground. Raise it just barely enough to clear ground. Or else you may flip over your whole tractor and die.

Finally a good video of this thing how I would use it!! I just want a front mount brush cutter for small/light brush. Every video I watch is it cutting sideways and cutting tree limbs. Thanks!!

Do you have any problem with foaming back in rear end?

Have you had any problem with fluid foaming in tank with return running in top of rear end?

How did you make your lil alligator clip that was helping you hold the wires?

Very good video. I looked at a Kubota L6060 today, and decided to plumb it as you have. You've saved me research on the fitting sizes, and I appreciate the recommendations.

HP? Demo of the 3 pt? Etc...

Nice work!

Nice job. Thanks.

Love our lane shark!!!

Looks very well made, just wondering why you didn't and a toolholder for a chain saw and maybe a ledge and shovel, etc

👍👍👍👍👍👍👍👍

Loader l2501?

So that runs fine off the front hydraulic connection? No auxiliary pump needed?

Nice work mate, I'll knock something similar for my little 38hp. Maybe a little more carrying space on top

Can you say what price we are looking at for this

Very nice.

Hooks on a bucket absolute must i installed 5 on my bucket. Each end and one in the middle and one between middle and ends. Nice Job.

Thanks for posting. Thinking of making my own also.

Hmph.....So that's what happened to Ecto -1.

Beautiful area!

pas peur du feu.....

I could watch grapple videos all day.