วีดีโอ

Attempted to install the supercharger but after hearing all the banging going on and seeing all that metal I’ve decided against it for now. Even fitting some Japanese quality bearings hasn’t helped. So I’ve removed the rotors for now and installed a dummy shaft.

Freshened up the valves a bit, new head gasket and a new base. I’m using one of my ignition boxes that I am going to utilize with my test stand.

Here we have two Whippets, the first being offered as a casting kit back in the 1960’s for hobbyists and machinists to machine and build to be fitted to the likes of a model boat. This 10cc engine was designed by Edgar T Westbury and the kit is still offered for sale today through Hemingwaykits.com. The green tribute engine (this one being made by Musa but also some were made by Enjomor) were m...

I should have mentioned that this engine was a pre order from when these were released 2.5 years ago and I qualified for the 50% discount on the blower as well so I have been sitting on this one for a while. I guess the only advantage in that is that I was able to see what issues others have had in their builds and I was able to eliminate some of those issues when I built this engine. I’ve spen...

Relocated the distributor to the side of the engine where it belongs. I’ve been calling it an L6….it’s correct name is I6-210 (inline 6, 21cc) #miniatureengine #scalemodel #scalemodels #modelengine #howin #inlinesix

I have finally got around to putting some new rings into this engine to try and stop it from spitting so much oil and blowing smoke. I’ve adjusted the oil pressure down to as low as it can go which is around 10 psi but I’m still getting a bit of smoke blowing out on one side, at least I’m not getting any more oil spraying out the exhaust. Checkout the last part of the video which was the last t...

Hooking up the ignition was the easy part. Then it played hard ball but I eventually got a pop out of it. Scale model engine. #miniatureengine #scalemodel #scalemodels #modelengine

Hats off to the master machinist that built this fine engine. It only required minimal work to complete. I’ve had to make the base, finish off the plumbing for the cooling, make a fuel tank, throttle linkages, fit an oil pressure gauge, make the exhaust trumpets, finish off the distributor, make a few adjustments to the carburetor and build an ignition system. Unfortunately atm it is not runnin...

After playing with my Benz car I thought it would be a good idea to fit some remotes to this tractor. I just needed 4 micro servos, a transmitter and receiver (RadioLink RC6GS v3) and some space for some extra batteries…and a few days to make a few brackets and put it all together. The servos fitted up nicely but I had to extend the back of the tractor about 12mm and I’ve had to remove the hand...

Toyan L400 scale model engine- Modified crankshaft supports with a 3rd, 4th & fifth bearing support

Scale model hit and miss engine based on a Rosebery (made by Stu Martyn)

Stirling engine from the Benz cart that is now mounted to the base that the R18 came on

Carl Benz motor wagon fitted with the R18 scale model engine

Atkinson cycle model engine

4 hours of tinkering with this scale model Benz wagon in 4 minutes.

Stirling model engine (with animation)

First test run of the Carl Benz motor wagon with Jin’s R18 scale model engine

Elmer Wall Mighty Mite 30CC fitted with the new hidden water pump

Elmer Wall Mighty Mite 30CC Scale model engine

Elmer Wall Wizard scale model engine

Elmer Wall Wizard 45CC scale model engine.

ET Westbury Seal 15cc model aero engine

Trying to get the R28 v twin model engine to run right.

A look at the features of the scale model tractor T26 made by Microcosm

Playing around with my Morton M42 scale model engine

Scale model hit and miss engine

Scale model flame licker engine

Vintage model flame licker engine

Playing around with my Morton M5 scale model radial engine