วีดีโอ

They are fun

depending on your weight. probably best to switch gears if possible,

Geat

Great investment to break the stress, I love mine

Hello, It is the model 70 but the motor is only a 63cc. Specs: Drive System: 2 Speed Gear Box (Thumb shifter) Seat Included: Yes (removable) Engine: 63.3cc 2-Stroke (EPA Approved) Top Speed: 35mph (weight dependent) Brakes: Front & Rear Disc Tires/Front: 11 inch Pneumatic Knobby Tire 90/65-6.5 (split rim for easy changing, with tube) Tires/Rear: 11 inch Pneumatic Knobby Tire 90/65-6.5 (split rim for easy changing, with tube) Max load: 265 lbs Max Range: 20 miles per tank Carton Size: 46x17x19 inches 71lbs Product Size: Standing 49x24x44in, Folded 49x24x20in Net Weight: 53 lbs Gross Weight 58 lbs Warranty: 60 Day Parts Replacement The Specs by manufacturer set max riding weight at 265 pounds for this scooter. Hope this was helpful

Thats a good question, I would check plug for fire/spark after making sure fuel is getting to carburetor. If you have Spark and you have fuel, it should run. Check on and off key switch if you have no spark, make sure the switch is not grounding out. You can disconnect the wires on the on and off key switch and try it. Good Luck

depends on weight of the rider. someone light like 150 pounds will do much better that a 250 pound guy like me. It also depends on terrain and grade of road/ up hill down hill That's the best I can answer, and hope you have a great day.

@@scooteroutfitters2780 thanks you too

Hello Brendan, Good question, I really don't know if the controller is compatible with your engine or not. If it is I don't see why it would not work. Mounting the controller I believe will be the challenge for you. Wish I could help more, but honestly I have never tried to add the Speed Controller to another Scooter. Have a great day.

@@scooteroutfitters2780 okay appreciate it yeah basically everyone on Facebook says a 26cc is too small and I don't see how its still gonna spin the gears at the end of the day so

Good question James, Unfortunately your weight would be an issue because of the bearings in the controller. You may be able to upgrade your bearings, and as far as the motor you can upgrade it also. Yes! I feel the weight issue is going to be a problem in the long run unless there is an upgrade on the bearings. Hope this was helpful.

I weigh 279 the bearings were not the issue. Its the gearing you will have to modify. A gearing set up for hills will solve the problem. Same issue as motorized bicycles. Once you set the right gear ratio your fine. A fast gear set up wont work. A set up for torque will work, even without a carb upgrade.

None in stock right now. Not sure on next shipment.

Thank You

This is not considered a Moped and I don't believe they will license it or yourself. Every State is different, So, don't take my word as totally correct. Call your Local DMV (Department of Motor Vehicles) and tell them exactly what you have and will you or your Scooter require a license. Hope this helped. Have a Great Day.

Hello El Paso There are places, but you will have to search for them. I don't recommend anyone because I don't really know the different companies. If you search I am sure you will find someone. Are they any good and are the parts reliable? (?) That's the real question that needs an answer. Sorry I could not help you on that. Have a great Safe Day

Hello again El Paso I would search UBERSCOOT Parts if that is what your son has. www MototecUSA.com carries parts but many times not in stock. Could be because they sell out so quickly. Hope this helps

Hello Jaqwe Bogar What is wrong with it or what is it doing. You may be able to fix it yourself

@@scooteroutfitters2780 when I received it the thumb shifter was broke wasn’t able to ride it, the key also was spinning

Hello Jaqwe Bogar, The thumb shifter wont stop you from riding it but it will keep you from shifting into the next gear which will give you more speed. You should contact the company you bought it from and let them know about the shifter. You should have a warranty. and as far as the key, that also is warranty and the company you bought it from should replace it for free. If you have waited too long and warranty has expired, try going to www.mototecusa.com and see if the part is available. Hope this has been some help. Stay Safe and have a great day.

Hello Christopher, Same here, except mine was on the first ride. Replaced the bearings with better grade bearings instead of the cheap ones from factory. It was not hard to replace, but a little time consuming. I have not had any more problems so far considering I am 250 lbs. Mine will run 35 with my weight. Was disappointing at first but its great now. Hope you get yours the way you want and running great. Thanks again for the comment and and be safe.

Hello Edmund, I believe its a NGK BM7A spark plug. Not at the shop right now. Sorry for getting back to you so late. Really Busy lately. Have a great night.

Hello Neil, Yes and really that is a great question. Many times when we attempt to start our scooter we wear out the pull rope and it breaks because either our gas mixture is not right or we have run our scooter alot and the spark plug needs to be cleaned or even the carburetor may need cleaned because water may have gotten in your gas. I have cleaned alot of carburetors on the 2 stroke and 4 stroke. Make sure your scooter has a good fuel filter to keep out any sand that might get in there when filling your tank. There are many things to consider when cranking up your scooter, whether it is New or Old Scooter. Maintenance is always something to keep up with on your Scooters 2 Stroke Motor or any motor. Thanks again for a great Question and we will get to working on that video. Have a Great day and Ride Safe.

Thank You

Hello Macho, I have that in the works. I will have to use my personal Scooter as a Demo. That will be a video coming up soon. Thanks for the comment and have a great day.

@@scooteroutfitters2780 thanks,and keep up with them,I enjoy them,I bought 2

Hello John, Not that I am aware of. Have a great day

cool....government usually has to mess with everything, even toys!

Hello VF, I don't see why not as long as your not in a big hurry. I am not sure what the laws are in each state you will pass through concerning scooters with a certain size motor, so you might want to check each state before you get on the road a see. It sounds like something I would do if I was way younger and had alot of time on my hands. Have a great day

@@scooteroutfitters2780 yeah its not something im planning on taking acrooss country just wondering the possibilities thankyou for the responses 😊

I believe that depends on the individual and how he maintains his scooter. If you mix the fuel correctly and keep the chain oiled and bearings greased. It should last a long time. You will have to learn to pull it apart and fix it when needed and carry parts in case none are available, like an extra chain, spare bearings, Extra throttle cable, and brake cable. The older the scooter gets they change the models after a couple of years and parts might get a little hard to find. I am not saying that will be the case with the UberScoot but I have seen it happen on occasion through the years with Chinese scooters. Hope that was helpful, and Have a great day

Yes thankyou

Hello John The 70X is a 63.3cc and the 50cc may not be compatible with the 63.3cc motor. You may be safer buying the upgrade parts made for the larger motor and brand. Hope that helped, and take care.

Hello Jay Yes the Uberscoot 70x has a key you turn on, and it does start with a pull rope. These scooters can be bought on our website at www.scooter-outfitters.com Have a great day

@@scooteroutfitters2780 How much do you charge to ship out to Mexico??

Hello Jay Cee, Unfortunately we don't ship out of the USA.

Hello Octuron (Big Dad), Thank You for the kind words. I love mine and just getting on it and taking a quick ride makes my day. Glad I was a help. Take care Big Dad and have a great day.

Hello DroneXFun, That's a great question and it would depend on the motor. You would have to do a bit of modifications. (I'm not saying yes you can do it). You would have to look at your clutch set up and see if the transmission will fit, and modify the chain length. (I am just making an observation). It sounds like a challenge, but you will have to do your home work on this as far as the compatibility with your motor. Hope this was a little helpful and have a great day.

Hello Bolt, Are your bearing bad? There are several bearings in the 2 speed transmission Controller. I will have to use mine as a demo. I have plans to do the bearings and do a video on adjusting Carburetor so it does not run too lean or too rich. I also wanted to explain the Chain tension, Belt Tension, and All cable replacements and adjustments. I have been pretty busy but will be making time soon to get these video's done. I am hoping that the parts for these Uberscoot 70x will come back in stock. we will restock our inventory and have these parts available on our website. Thanks for the comment. Take Care Bolt and be safe.

Hello Alfie, I am so glad it was a help. It's amazing how simple some things are when explained a certain way. You made me feel good, and assured me the video is doing what I hoped it would do. Alfie, You have a great day, be careful and stay safe out there.

Hello Super Hurricane, That is a good question, Unfortunately I am heavier that 150 pounds, but I can tell you at 250 pounds it carries me at 30-35 mile per hour (MPH). We have a few left on our website at www.beaufortminimotorsports.com, You can also go to www.scooter-outfitters.com or www.scooteroutfitters.com I love riding mine, and for a guy as big as me I have no problems. If you haven't gotten one, you should. You will have the time of your life. Remember always wear the proper safety gear while riding. Stay Safe Super Hurricane, and Have a great day.

Hello Bolt, Praying is not a bad idea, because I don't see any chains available. What we normally do if we have a customer that needs a chain and we don't have one in stock we try and find one longer than the one that's needed and we remove some links to make it the size we need. You might give that a try. You can also keep looking around for the chain online, but I think most of these dealers get their parts from the same supplier they get their scooters. If we see a large demand on certain parts we will make a special order and have them shipped in. Sometimes takes 3 weeks to get them from China but at least we have them available. Hope you find a chain and Have a great day.

Hello Bolt, Possibility either a wire in the shielding from the key switch is broke or your key switch is defective. I would have someone ohm the switch out to see if it is getting continuity. Easy fix but you will have to order another switch if that is the problem. Hope this was helpful. Have a great day and let me know if you have any questions.

Hey Hoboken, What it doing or Not doing?

@@scooteroutfitters2780 not spinning the wheel when I rev it

Have you checked your belt tension on the 2 speed gear box, The gear box has a small clutch disc in it, but also you have your Clutch that operates by centrifugal force on the motor where the Gear box attaches. It sounds like a clutch problem to me. Have someone check that out. I have not seen any problems with the clutch on the motor, but I have seen tension issues with improper adjustments to the 2 speed gear box setup. Hope it gets fixed because it is a good scooter from what I have seen so far. Any scooter will have issues sooner or later. Let me know how it turns out. I need to do some videos on diagnosing certain problems that occur with these UberScoots 70X 2 Speed. Take care and hope you get it up and running soon. We we are here if you have any questions.

@@scooteroutfitters2780 ok thx

Hello Jeff, What Part are you looking For?

Hello Bolt, When you get your Scooter you will want to find out what the oil/gas ratio will be for your scooters BREAKING IN period. You may have to mix your oil at 25:1 or 30:1 for the fist few tank fills and then move it to 50:1. Your 40:1 will not hurt your scooter if you mix up a gallon with that, but try to stay with what the book says on your scooter. I always figured the people that Manufactured the scooter should know the best route in maintaining their scooters, so see what the manual that comes with the scooter says and try to stay as close to it as possible. They should send you a Plastic Mixing fill bottle with 2 different mixes on it. 30:1 on one side and 50:1 on the other. The 40:1 mix oil you have is just measured out for you in the bottle, but the oil itself in the bottle is 2 Cycle oil that can be used to pour in your plastic mixing bottle as you seen me do in the video. Your Oil/Gas Ratio will always very depending on how much oil you add to the gas. Hope I made that simple and have a great day Scootering.

Hello Bolt, Great to hear you got some help, and Bolt, be safe when out there riding and try and wear the proper safety gear. we are here for any other questions, have a great day.

Hello Korey, If the engine sounds like it is trying to move the scooter but does not move it, your chain could be too tight. Many times when these scooters come from the factory they seem to tighten the chains too tight, so check that . You should be able to push the scooter Forward and if it does not push forward, again it sounds like a chain that is too tight. Try looking at this quick fix first and let me know what you find. Also make sure your brakes are not too tight causing the issue. Have a great day.

Once your oil is mixed right and you prime the carburetor with choke on it should fire right up after a couple of pulls. If it does not crank after about 5 pulls there is a problem and most of the time its a simple one. Getting a New Scooter can get you nervous when it does not crank right away, but the fix is usually something you overlooked when getting it ready to crank. Hope all is well now, and have a great day.

@@scooteroutfitters2780 ya thx it was frustrating...I'm new so I don't know what's up maybe its just a new motor thing just trying to dial it in. . . The shifter things really six tho

Ya two weeks later still working on. Not cool.... I've only gotten to ride it like 6 times wtf. Bad reviews from me the first day. My gearshift broke... no replacement part still Bunch of crap from customer service

Hello Steven, It sounds like a carburetor adjustment issue. Your motor can run fine without a load on it, but when you get on the scooter it has no power or pickup. also make sure you mixed your oil and gas correctly. Sometimes the heavier oil mix on the scooter can dirty up the spark plug where it does not fire as well. I'm really not thinking spark plug unless the plug was bad to begin with. Hope there is not an issue with a slipping clutch in the gear box. I would only think that if your scooter will run at full throttle and full RPM and no speed. No Speed meaning 10 -20mph Sounds like a simple issue with it being new but its really hard to guess any further without seeing and hearing it ourself. I hope this little bit of information has been helpful and we hope you can find the issue. Have a great day.

Hello Bernardo, I will try and do a video on replacement shifter and cable, but that is not going to help you now. The cable from the shifter goes down inside the gear box and connects. You will have to pull the plastic cover off the gear box that surrounds it and look where the cable connects. You will also have to adjust the cable after installing it. You might find someone you know to help you with this that knows a little about mechanics. Good Luck with getting your shifter installed. Wish I could be of more help at this time, Have a great day.

Mines broken to pretty much fresh out of the box it snapped 🤨

@@scooteroutfitters2780 tried to switch it once brokd my thumb and shifter lol I need to connect the company.. .is there a way to actually fix Shifter it self

Hello Hoboken squat cobbler, The Shifter is adjustable. In the gear Box where it attaches has an adjustment there and if that does not work good enough you may have to loosen the cable from the gear box and adjust it that way, Also right on the Shifter where the cable enters, it has an adjustment screw there also. I know my shifter was pretty tough when I first got it but one of the bearings in the gear box went bad and I had to replace it, but Once I I assembled it and had everything adjusted correctly it shifts super smooth. I really don't know why mine was stiff at first. I believe there is a video somewhere on the adjustment of the shifter cable to the gear box on TH-cam. I may have to start using mine as a teaching tool on Video for all the issues I keep hearing about on these UberScoots 70x 2 speed. Hope you get it fixed.

@@scooteroutfitters2780 thanx shifter already snapped Hopefully there's a way to repair..... my bad

Hello Reuben, These are much tougher and powerful than a regular weed eater Motor. These UberScoots 70X 2 Speed can be purchased on our website at www.scooter-outfitters.com or www.beaufortminimotorsports.com I have been riding my UberScooter 70X Scooter and it has been great for a guy like me that weighs 150 pounds and the scooter runs almost 35 miles an hour with me on it. It's Great. Get Yours ordered today on our website. You will Love it. Have a Great Day.

Hello Hoboken, I cant really answer that cause I'm not familiar with the extreme xg. If the company would like to send me one to test the difference in the 2 scooters, I would be glad to post the results. Sorry I could not help on this question. Have a Great day

@@scooteroutfitters2780 well I'm having major issues I've purchased the uberscoot and have not been able to get it running properly. PoS... Frustrated

Hello, You can get your 2 cycle oil mix at any hardware store or even Walmart. Just make sure you mix your Oil and Gas according to the Scooter instructions Manual. There will be an Oil Mixture to follow for the first few tanks full. Then you will run it at the regular mix. Every Scooter Comes with a Plastic container you use to make up your oil and Gas mix. One side of your container will read 30:1 and the other side 50:1. This means for the first few weeks you will run your scooter at 30:1 (30 to 1) this means 30oz of gas to every 1oz of 2 cycle oil. Then after the (break in) period is over your Gas/Oil will mix at 50:1 (50 to 1), and once again this will be 50oz of gas to every 1oz of 2 cycle oil. Learning to mix you gas and oil correctly will keep your scooter up and running like it is supposed to run. Bottom line is that all scooters are different and make sure you follow the Manufacturer guide lines on mixing your fuel and to what ratio they recommend. I hope this has been helpful.

Hello, You can get your 2 cycle oil mix at any hardware store or even Walmart. Just make sure you mix your Oil and Gas according to the Scooter instructions Manual. There will be an Oil Mixture to follow for the first few tanks full. Then you will run it at the regular mix. Every Scooter Comes with a Plastic container you use to make up your oil and Gas mix. One side of your container will read 30:1 and the other side 50:1. This means for the first few weeks you will run your scooter at 30:1 (30 to 1) this means 30oz of gas to every 1oz of 2 cycle oil. Then after the (break in) period is over your Gas/Oil will mix at 50:1 (50 to 1), and once again this will be 50oz of gas to every 1oz of 2 cycle oil. Learning to mix you gas and oil correctly will keep your scooter up and running like it is supposed to run. Bottom line is that all scooters are different and make sure you follow the Manufacturer guide lines on mixing your fuel and to what ratio they recommend. I hope this has been helpful.

@@scooteroutfitters2780 ok thank you I saw on the manual it says a certain kind of oil could you tell me what oil you use and what store to buy it from thank you

@@maxxarmstrong4467 don't forget to pick up some blinker fluid as well Its a ruff ride with it..

Hello, and thank You, I Try not to be mean, and just enjoy a good ride and try to get along with everyone. Hope you have one of these scooters, or plan to get one. It really helps with the stress and boredom in life. Tough on my rear end on these bumpy roads at 60 years old, but I still enjoy riding it. I do it cause it's Fun. There is still a little kid inside all of us, specially me. Thanks again PhotonsAcrossTheAir and Have a great day.

@@scooteroutfitters2780 hey hey, yeah you certainly trike me as a genuine guy :) most importantly im glad youre having fun. i actually have the Fluidfreeride Horizon. fun but only goes 23mph. im saving for a 40mph one like the Kabo Mantis or Apollo Pro. thanks for the comment and really hope your have a good day :)

Thank You for the visit, those Kind Words and please stay tuned because there is much more to come. Have a Great Day.

Hello and No we are open. We are doing all our business on our website for now and we give the options on check out to have the item shipped to your address or have the item shipped to us at our shop so we can put it together and check everything out and then call you to come and pick your item up. Some motorsports like our motorcycles and go-karts, even the little pocket bikes need put together. This gives us a chance to check out everything before you pick it up local. You have the option to have it delivered directly too you without local pick up. What ever makes it easy for you our customer. Some items we have in stock and other items will have to be shipped from our suppliers warehouse. We operate a small shop to keep prices down for our customer and still make repairs and provide parts as needed. Hope that helps, and have a great day.

So if I Oder it now how long it will take to get to me 5 weeks 4 weeks 3 weeks 2 weeks 1 week

We are here.

Right now all purchases are done on our website at www.beaufortminimotorsports.com