วีดีโอ

What about the pump? I don’t hear anything when I turn it on, This is my prob too. I don’t hear the pump. The error goes away if I shove the garden hose into the intake and run the hose at high power then there is no error so I think it’s the pump?

Thank you for this amazing video. I’ve replaced my Impeller before. But i never realized how the flow sensor was problematic and my issue. Great video. Very clear. Well made and it helped me fixed my E02 code and probable from pulling my hair out in aggravation. Found the new sensor replacement on E Bay thanks to you as well.

Thanks a lot for the great video! 👍 Unfortunately, I have a newer model that is more square than egg-shaped. Inside, everything's pretty much the same, some "improvements" aside that make self-repair a bit more tiresome. Mine showed E02 the other day, which usually indicated a dirty filter. Swapped the filter, no change. Today, I tore it apart to inspect the plumbing. All the tubing, the flow sensor and the impeller are free from gunk and debris, nothing is bent. I slowly started to put everything back together and tried to fire up the pump sporadically, but it only turned on once and stopped after a few seconds. Funnily enough, it does get 12 V AC and there's nothing inside that would impede rotation, yet it refuses to turn on. 😳

Thank you for your thorough walk through. I had just about given up on my unit and this video saved the day. My impeller looked just like the one you pulled out.

It’s a hot day outside and the water is 98, also a brand new filter. I noticed it doesn’t give me errors and runs perfectly fine until the filter is on

Its 20oC in the uk and im getting e03

What about e03

Great video. I have the new impeller kit on the way and I'll probably be tearing into mine tomorrow, but knowing how that sensor works and that it's the only thing triggering the E02 is key in understanding how the system works in order to resolve it. Thanks!

I used a multimeter like you showed, and a quick burst of power occurs, then cuts out when e02 fires again. Does this automatically mean the circuit board is bad? It doesn't appear damaged with burnt wires, etc. Thank you for a great video👍

Thanks for this, it was the impeller on mine,cleaned up the flow sensor as well just to be on the safe side. Ordered parts from Amazon too as suggested. Thanks bud 👍

Sorry I have one pomp bestway Idromassage but no work good. it doesn't heat well when I turn on the internal vat with bubbles I feel it hot when I put it in heating mode it doesn't heat up what can I do?

Awesome guide, ended up being the flow sensor magnet, cut the old one out and epoxied one in from the hardware store. Cheers mate

I sat through 20 videos of people just changing the filter before i found your video. Thanks so much for taking the time to make this. It gave me the confidence to take mine apart and it was the impeller too. One small comment i have is you keep pressing the heating button with no water in the pipes, i would think this could overheat the element. You can just press the filter button which will put the pump on without the heater.

Man your a life saver 🛟 had this given to me from a friend that was moving. but had sat idle in a building got the e2 right off the bat,was the pump motor for the 22 bucks can I send you a tip cause I was about to buy a new egg for 250

This is the BEST video explaining the problem with these units, thank you. My egg died 2 years ago after 2.5 years of use. I took it apart but couldn’t get it working again so I bought a new spa. Here I am less than 2 years later and the new one stopped working with an E02 error yesterday. I know it’s the impeller that isn’t working and not the flow switch because I was able to force water through the intake to simulate flow and I don’t get the error. Now the question is- Is it the pump motor or the impeller? Although I’m working with the newer rectangular egg, your video has given me enough instruction to take the plunge (so to speak) and see if just an impeller replacement is required.

Sir i never ever leave comments to videos unless info is right and super usefull, sir you saved me from a new saluspa, i just dissasembled it and clean the pump and wow working just as new and i cleaned the flow sensor too, i will get the pump kit just in case, a huge thank you to you!!!!

Bad news is they don't sell in the United States.

I was about to give up and get a new spa, the pin holding the waterflow magnet in place in the sensor unit had snapped off and the magnet arm had moved down the pipe inside, easy fix once I found that, thanks. Your video gave more insight into the workings of the system than any others.

Still have the e02!😢..changed impeller and flow sensor with new parts.. how do you fix it when u don't nt hear any noise when turning the heater on ..and you get the e02?

Finally someone that can fix anything! Awesome video! Thanks.

I never write comments, but this is one of the best made, fix-it videos. I've watched tons of E02 stuff but your video is the first to be so comprehensive and clear.

I inspected the impeller. It’s fine, good. I looked at the sensor and now I’m getting E01 error!

Thank you so much for taking the time to do that. Mine was cracked and rusted exactly the same way. Just ordered my kit!

Appreciated your video very much! We're still stumped with ours... could it just "simply" be that the pump itself is busted? If that's what it was, would we be getting a different error message than 02? After taking it apart, multimeter reading was fine, impeller looked totally fine, no tubes were twisted. Also the flow sensor was fine (in that nothing seemed broken and we were able to recreate the error 02 bypass that you showed by holding the magnets together). With ours, we hear nothing when we turn it on (except for the initial click). How can we know for sure if in fact it's just the pump itself that's the problem? If it were, unfortunately it doesn't look like you can buy a P4071 anywhere anymore. But it would at least be good to know, in case it's something else...

Super helpful video but I have a question : this helped me a few months ago, and now I am getting the e02 again now. So I dismantle the thing, and I start with the flow sensor. I made a makeshift bucket/tank to test the system as I went along. Oddly enough, the pump and whole system runs when connected to a home depot bucket. I then take it back to the hot tub, plug it in, e02 error. I am going to do further investigating but is it because the pump is getting a different pressure from the water in the small bucket than the hot tub, and can't quite move in the hot tub scenario? In any event, it seems to again be a pump issue but it happened so soon after the first failure, making me wonder if there's anything else I'm missing. Thanks un advance for any reply.

Thank you for such a great video with links! We reaply thought this hot tub was too good to be true but your vid perfectly explains the drawbacks.

Exactly the info i was looking for, thanks a million ! i want to use my HT for a little while longer before i have to pack it away for winter

I have the Coleman saluspa, it looks slightly different from this, and the flow sensor is in a small Grey rectangular box (looks like an outlet box). Sensor was clean. Inside the heater had a little white flaking, I cleaned it with a straw brush. Impeller looked fine. I run the thing even with no filter on, and it shuts off in about a minute. E02. A while back my gfci plug had melted for some reason, I replaced this with the same one. Any idea what could be wrong?

You nailed it! I was ready to throw everything out. Your video prompted me to check these things. Vola!, same, same. Back in business. Thanks!

Just want to give you a HUGE THANK YOU for such a fantastic detailed video! I got the dreaded E02 coded after 2 1/2 years of continuous operation of my Coleman Havana model. After checking everything else, I opened up the egg and found the same cracked pump rotor. Ordered a kit on Amazon, put back together and back in business. You are AWESOME!

Hi, I need help. My daughter give me her hot tub that has a colemen salusspa error 02. I cleaned the filters and still error 2. Can someone me how step by step to check for seeing if the filter is plugged? I am a senior I am lost. Can anyone help me?

Im gona have to glue the sensor magnets shut, this stupid 90s tech thing errors after 3 uses on a brand new spa

I dont hear my pump come on. We had a power outage 3 or 4 times in a row so i think it messed rhe motor. Every video only addresses propeller.

I have been through 2 pumps one saluspa E02 and it would not even blow up the tub?? So they sent me a green egg same thing E02 first one made that horrible noise the green egg just give code and shuts off😳then the crazy company sent me another tub itself they thought that was the problem but no!!! I have 2 hot tubs and both don’t work….. so I’m taking it back and I’m going to try to fix the green egg one!

Thx man!

Dude you are the man thanks

Thank you for the video! My impeller looked identical to yours in regards to where it was cracked. I just installed the new one, turned it on and got an E01 code. So I took the flow sensor off and cleaned it up, held it shut and turned on the pump…all good. I followed your instructions to the letter and now I just hope it works when I set it up in a couple of weeks. 🤞

What would you recommend after changing pump,transformer and circuit board and still pump does not fire up 😂

I will try and see how it goes but I did take apart my rusted propeller or whatever it’s called and it is rusted. I might get the flow thingy to.

Thank you so much. Having this exact problem. This is the best video I've watched for this problem. Again thank you for being so concise in your video.✌❤☀🌈

Thanks a lot for this concise video! I am getting this stupid error and believe that the flow sensor is the cause. Once again, thanks for sharing this!

Thanks, Bro, it worked! This easy fix saved so much time!

Thanks for the info, I was setting mine up out of the box. It was cold out, brought the pump inside and blew a hairdryer through the water inlets for a couple minutes, hooked it up and it worked!

I'm having the same issue but my outside temperature is 30 degrees celsius which is very hot!therefore it can't be that it's too cold outside and the pump needs to warm up with a heater! What's wrong with this thing? It's brand new!

I didn’t bother taking the top off, just draped a tarp over it and warmed the space with a hair dryer. Didn’t take long.

Have you had E04 error yet? I can’t seem to clear mine.