วีดีโอ

Lift tables for the win, however i wouldn't waste the $ on a h.f. table. Yeah, other lifts are more expensive but the stability, speed, quality, and saftey are worth it. If your going to invest in a lift that takes up so much space, you should get a quality unit.

Inter locking kids floor pads

Hey , great video! Keep up the good work.

For the amount of material needed for just the seat pan at my local metal supply would be around $10 at most, SS too!

😎👍😎 So...1 yr later..how's the chopper running and riding...??

😎👍😎

Would it be possible to remove the under seat oil tank and to put in a WLA oil/gas tank with the shovel head?

I have been polisjing my shovel as well. Easily put 10 hours into the inner primary alone

It’s been 3 months now right….hows it looking? Any fading or anything yet?

Get To The Point! You just keep rattling on!!!! I’m Gone!

Cleaned him up real nice! 👌

That looks great. I will say that everyone else doing this suggested not doing it in the sun. I guess it drys pretty quickly and causes streaks. I’m definitely doing this to my old ford.

This is like an advertisement for every upholstery shop, even the crap ones because this ain't it.

Only problem with the Craftsman style is you can't use them on bikes that have the exhaust run beneath the bike, ie my Suzuki Bandit or my Yamaha Virago.

What frame did you start with?

Good video sir! I have the bike lifter you showed second, alright for small jobs but don't like it for bigger jobs. I also have a table similar to your one. It is branded 'Clarke' and is both hydraulic and air. It has 3 'D' rings down each side. The lift pedal is removable as is the lowering pedal and the lowering pedal is also shielded so you can't stand on it accidentally. It has a 3 position locking bar and has a levelling jack at each corner. The wheel clamp has 3 positions too. All the best from IoM 🇮🇲

Thank you for this video. 🙏🏼👍🏻🇺🇸🇺🇸🇺🇸

Apparently the parts truck included a "stud"

🎉🎉🎉

I want one, thanks!

nice

Hi. Great helpful vid. Question... You show the chrome headlight bracket bolting on to the lower tree through the two front holes. Aren't those holes also for tightening the tree to the forks or dual purpose? Wondering cuz I thought to see a torque wrench used. I am piecing a build together and guess I need a headlight bracket to go under the two bolts I just installed which I thought had sole purpose of squeezing the tree slots closed around the fork tube....

Congratulations on the subscribers. I did speedway racing back in the 80s. It was stupid expensive, life took over, had to drop it. I remember painting my daughters room a similar color, almost 25 years ago. Damn, times flies. Enjoying the videos, looking forward to the next.

Congrats on 1k subs! 🎉

Hell yeah !!!

do more uploads plz

Get it daddy

Get it daddy!🎉

Get it daddy

I've owned my 2006 FXSTBi from new. The rear is dropped so far it now has 2" of rear suspension. It has 4" over forks. It IS a chopper!!

😎👍😎

A chopper is a type of custom motorcycle which emerged in the US state of California in the late 1950s. A chopper employs modified steering angles and lengthened forks for a stretched-out appearance. They can be built from an original motorcycle which is modified ("chopped") or built from scratch. Some of the characteristic features of choppers are long front ends with extended forks often coupled with an increased rake angle, hardtail frames (frames without rear suspension), very tall "ape hanger" or very short "drag" handlebars, lengthened or stretched frames, and larger than stock front wheel. To be considered a chopper a motorcycle frame must be cut and welded at some point. I.e. the name chopper. The sissy bar, a set of tubes that connect the rear fender with the frame, and which are often extended several feet high, is a signature feature on many choppers.

Nuttin but a MONEY PIT! 😊😅😮😢😂

A chopper is a chopped up bike. End of story. Lol

Yes, there is. In order for a motorcycle to be a chopper, the frame must have been cut and significantly altered from the factory form. Hardtailing a swingarm frame or raking the neck for examples. A Bobber has had factory installed components removed and not replaced to reduce weight.

Very cool bike! 🔥🔥🔥

The weight of the motorcycle and gravity is the reason your table leans towards the drain, its downhill.

It always feels good to get an old machine going again.

Awesome content,please keep them coming 🤙

was wondering what you thought of that engraving tool.

My S&S doesn't have a tear drop air cleaner. It has a rain drop air cleaner because there ain't no cryin' on my bad motor scooter!

BRO!!! I have to know exactly what that blue/purple metallic paint is! That’s what I’ve been looking for!

Cool project, looks nice! I like how you're not afraid to take on different challenges, that's what it's all about! Never stop learning! Take er easy 🤘

Digging the Abyss logo on the rear, still practicing the pinstriping? It's a cool hobby, I got into it about five years ago. Haven't done much lately, except my helmet, I got a video on it if you feel like checking it out, have a good one 👍

why not just make 10 hotter?

hell yeah man. looks like she's running well. nice cruise around the lake.

i thought i was gonna learn how to get em so clean but you got a lathe that aint happening i gotta go oldschool with a grinder

Thanks for this video, does it FLH frame ? What is the different FLH and FX frame ?

👍🏻🇨🇦