- 4
- 11 433
Akechi San
เข้าร่วมเมื่อ 21 ธ.ค. 2013
วีดีโอ
Clutch Delay Valve/damper delete for 13+ Honda Accord
มุมมอง 8K8 ปีที่แล้ว
CDV delete for 13 Honda Accord V6 Coupe Manual. It should be similar or the same across all J-series 6-6 platforms. Note: this only applies to manual transmissions. *Unfortunately for 2016 models, the VSA cannot be fully disabled. There is a sequence you can use like a cheat code to override the VSA and fully disable it. That is why the VSA is blinking. Disclaimer: I am not responsible for any ...
Morimoto XC LED demon Eye retro
มุมมอง 9919 ปีที่แล้ว
this is my Demon eye retro for my 9th gen accord coupe. Song: All We Need Artist: Odezsa disclaimer: I do not own this song and I did not write it.
Tuning 3G TL bix projectors for retrofit
มุมมอง 1.8K9 ปีที่แล้ว
3G TL bix projectors upgraded with TL-R mh1 shield mod and ZKW-R clear lenses. song: It's Only - Odesza
How were you able to disable your traction control like that? I have a 14 and can’t get it to fully disable.
piston
To anyone that still wants to do this: just drill a hole for the ring. I drilled a tiny hole in the gap between the ring on the cap (right near the ring, not too low so you don’t damage it.) and pushed a pick inside and I had it out in around ~5 minutes. Highly suggest.
Where exactly do you drill. Side or top thanks
@@Pokka676 side
@@crowdkilleryote I’m doin this now and that ring is came out so easy. Thank you brother
@@Pokka676 no problem I wish I had known it was gonna be so easy I wouldn’t have bought a new one
Not even it’s first oil change and being dogged 🥺
Have you even tried to drive one of these with the clutch delay? This isn't dogging it, it's making it more driveable.
is that an HFP deck lid spoiler? And can you make a video with how your borla exhaust sounds (start up, revs, eco mode revs, stop and gos) Thanks man
The Lip Spoiler is not the HFP one. It is the Spoiler King duck bill. I can definitely look into putting up a video with the borla. Unfortunately, I don't have a cameraman so it may be a while before I can release a vid.
Great work.. after you drop the lenses in do you actually have to spin them to get a sharper cut off?
Evan Reynoso we used the zkw-r clear lens and changed the shield to the TRS TL-R shield. The TL-R shield is a replica after the H1 shield and using the H1 high beam solenoid.
Also spacing it with lens spacer give it some color.
I am so doing this.
think it's the same for a 4 cyl 8th gen accord? thinking about doing this
Mauro Beltran the slave cylinder should be the same or similar. so the process shouldn't be too different.
Gratzie for the reply
Looks sweat man!
you should really have a hose connected to the bleeder screw on the slave attached to a bottle of fluid. watch for air bubbles in the fluid.
TheShangralaaaa17 yeah. I can't seem to find a clear hose that'll fit the nipple correctly.
Do you have a tutorial for installing projectors for the high beams? Im planning to install projectors on my 8th gen coupe
For those who are going to be doing this mod, DO NOT BEND THE HARDLINE! You could cause a leak and be waiting a week for the part to arrive
Finally...like u said no one has done a j series vid.. So did u notice a big difference on the take off from a dig. That is the main reason I want to take mine off. It's hard to engage on the dig some times.
macedonio450 well, I typically don't launch my car too much but it'll definitely make your shifts more solid. After all, removing the damper will allow the clutch the connect quicker, which theoretically should speed up your shifts.
would love to see these on the car!!
very nice work